Two things come to my mind. One is failing electrolytic capacitors on the main board, Electrolytic capacitors can cause random microcontroller crashes and all sorts of weird behavior, And they can be intermittent too. You can try heating the main board with a hair dryer when it decodes to not work and if it comes back to life after that then it is likely to be the capacitors. The other thing i would do is check the sensors on the dryer, Maybe it is running the fan and throwing up the error because it thinks the element for the dryer is hot. I personally suspect electrolytic capacitors on the board because they are notorious for failing and causing intermittent behavior.

perhaps a contender for a bit of brick washing

The wash indicator LEDs on the right indicate what the fault is on these machines, in this case F02 is displayed which is an issue with the motor, usually motor tacho but not always. Dryer fan runs as a fail-safe feature when a fault occurs.

The processor of the board is brocken, it also this doing. I fitted a used new board an it still works fine

my iwc indesit had a similar fault as this but none of the wash icons would show only the top lights would flash, it would flash randomly whenever it wanted to no matter at what stage it was at. i did fit a new board to it but turns out it had even more issues as the drum had a crack causing it to leak on the motor which resulted it not being able to control the speed very well so just ended up feeding it indesit moons motor. to fix this you could have swapped the wires and facia panels if that was something you really wanted to do just to get it to go

Pressure Switch, probably the hose to it is partly clogged, it is loosing track of how much water is in it.

These Indesit are a pain in the ass! Fault 1 - Could be Motor Triac -The Module needing to be totally replaced Fault 2 - Could be the motor itself being jammed - or the motor Tacco being a problem . Fault 3 - Could be the NTC - motor temperture sensor being toast (were the element is) check the connections replace if needed Fault 4 - Could be the pressure switch being broken. Fault 5 - Could be a heater relay being damage and needing replacing - check the element if element fine, new module is needed. Check all connections Fault 6 - Check drain pump connections and wiring Fault 7 - Check dryer for clogged or problem with the fan motor. Fault 8 - Check dryer for connection problems Fault 9 - Check on main board heater relay problem (replace if needed)

I happen to have a similar case at home. I totally gave up on getting a new spider for the Indesit WIXXL 146. At the same time I had the WIL125 which I built, and had no controller for it. So, I put the controller of the WIXXL146 into the WIL125, For some reason, the drum turns much faster during washing/rinsing. Other than this it worked fine... but after 4 washes, it began to trip the MCB randomly! Most likely, it is caused due to the excessive banging of the tub against the body, possibly hitting the wires? I will try to make a video of it soon.

Got the same washer dryer load of bloddy rubbish pump blocked up on mine and stop draining the water and all the lights was flashing on the front panel ok since done the pump!!!!

my grandma had this washer model and the pcb was broken and the motor and we didn't know what to do so we took it to the scrap yard

indesit washing machines are problematic. I came to this video for the non-ending wash cycle issue on my Indesit washing machine. I have another Samsung inverter washing machine which has been working for 6+ years now. No complaints or issues.

These indesits when you start them will fill through the pre wash then sit and do nothing for couple mins then fill through main wash and start not sure why they do this

For this one i don't know what to say as i am a expert at brands like beko/bosch and candy but if the other pcb doesn't work then brick it

Weird that it doesn't pump when there's water on spin, along with other weird faults something really wrong is going on with it

I used to have a hotpoint Aquarius washer dryer 8kg wash 6dry. 1550rpm graphite. And for some odd reason I would come home sometimes all the lights flashing and all soaking wet especially on pre set drying programs it would do it more but not on the timed ones 🤷🏻‍♂️ and most of the time on final spin it would take 45 minutes to balance a load and spin it if it felt like it ?? But would spin fine during rinsing 🙄 was never blocked nothing burnt on the board sump pump filters all clean trap at the back for waste nothing… it was mystery 🤷🏻‍♂️ gave it away it still going but still plays up occasionally but she doesn’t use the dryer on it. Mind I had a cheep indesit iwc6145 for years never let me down till the end 6 years.. drum spider literally snapped off lol. Guess it’s luck can’t believe they still look the same as 10 years ago lol 😂

Nice👍

Linear Pressure Switch

good old indeshiT, the old 80s early 90s indesits were ok, if its not brushes, element , or thermal fuse inside motor, its the pcb, dont bother if its the pcb, but id take the brushes out & check them 1st

You got another?

The washing machine been sick lol 🤣🤣🤣

pressure switch or door lock

👍👍👍👍👍

Loose connection maybe?.

I would not get any new Indesit or Hotpoint machine imo

The PCB board nacked on it

the motor might just gotten overheated

just get a Hotpoint wma 32 washing machine

And this is the exact reason I hate indesit machines and would never buy one👍 great vid

Ugh! I find Indesit machines horrible nowadays. They just feel full of plastic and they could easily break at the slightest touch. I would never have one personally.