#bosch

Рет қаралды 120,710

Жыл бұрын

Thanks for watching . And do not forget, Like and Subscribe
Due to factors beyond the control of CMC DIY, it can not guarantee against unauthorized modifications of this information or improper use of this information. CMC DIY assumes no liability for property damage or damage incurred as a result of any of the information contained in this video. CMC DIY recommends safe practices when working with the tools or equipment seen or implied in this video. Due to factors beyond the control of CMC DIY, no information contained in this video will create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from the improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not CMC DIY.

Пікірлер: 36

@lauretiu 3 ай бұрын

sir, thank you very much!!!!!!!!!!!!!!!!!!! you saved me having to spend 60-80$ on the motor when the whole drill is less than that! thank you thank you thank you!

@FixitEasyDIY Жыл бұрын

Big bravo for the easy fix. Can I give you a little tip: after this procedure try to dip the motor in water for couple of minutes running at low voltage. It will clean all carbon in the armature and polish comutator contacts. Believe it will make it run even smoother. You will probs need to change the water couple of times until it becomes clear. Thanks for that video!

@CMCdiy Жыл бұрын

Thanks for the appreciation, I will try this cleaning as well.

@pillaydaryldeez3707 Жыл бұрын

Water in motor ???? Is that even safe to do ?

@dharmakissoon 11 ай бұрын

@@pillaydaryldeez3707 i did it to a gas electric pump in water, surprisingly it ran

@zinzin8891 8 ай бұрын

You can also soak it in isopropyl alcohol or give it sonic bath. But it's only help you in case pins give you short with engine housing and that's why you have sparks.

@user-bv7pg3ks4s 6 ай бұрын

I used eletronic cleaner spray on mine, and it got a lot of the dirt out, I used it until i saw saw no more dirt from all angles, and sanded the contacts as in the video above

@ErCanEverything Жыл бұрын

Very good job thanks for the video my Friend🙂🤝🤝🤝

@CMCdiy Жыл бұрын

Thank you too

@croakingembryo 7 ай бұрын

Great video, thanks! Mine had one of the brushes broken off.

@mikegraham8319 18 күн бұрын

Cut a strip of sandpaper and cleaned the commutator through the top two holes without needing to open the motor ... gr8 video tho 👍

@sigillodiro Жыл бұрын

Very good job friend👍✋💯

@CMCdiy Жыл бұрын

Thank you

@pillaydaryldeez3707 Жыл бұрын

Give you a like . But next time try using a vice of some sort ,to hold the motor during test, as to not cause any injury

@CMCdiy Жыл бұрын

Thanks

@madulaamblanggata705 3 күн бұрын

Cool as heaven

@orlatris96 Жыл бұрын

Good job, thanks

@CMCdiy Жыл бұрын

Thank you too!

@lookup49 5 ай бұрын

I have a similar motor for a battery operated mini chain saw. It will start and run but only if I set the shaft on a certain position. Most of the time when power is removed it will not run until I turn the shaft 30 degrees. Is this a commutator problem?

@ashfaqquadri8408 7 ай бұрын

Make Rs 550 dc motor rewinding video...... Plz

@adrianomorais3112 4 ай бұрын

Opa amigo tem algum grupo ? Mais dicas

@Aptarus 8 ай бұрын

What i should so if i want to avoid buying a new driller. I'm more or less comfident i understand the steps so thanks in advance (although I'm still unsure if and when I'll try it).

@Aptarus 8 ай бұрын

Sadly I couldn't get to open the back piece. You have better hands or nippers/pliers than I. Probably both.

@croakingembryo 7 ай бұрын

@@Aptarus I also struggled with this but eventually got it bent with just regular pliers. Not very tidy but I was past caring by that point. Then to get it open I had to wedge a screwdriver into the side holes and pry it open with a lot of force (screwdriver even bent). Anyways, it eventually opened up.

@Aptarus 7 ай бұрын

@@croakingembryo great for you ! I ended up ditching the drill, my motor's backplate was far too damaged (and I'd spent too much time trying) but at least it made an interesting and enriching experience. I bought a brushless one so at least this won't happen again - something else will break. (It's DIY year as I just had to replace my phone battery - this time with success, while 2 pro refused to try out of fear of breaking the screen)

@prerupa 6 ай бұрын

3 slot armature with a motor this size?

@user-ky7yo8zp9g 7 ай бұрын

Ну, заодно, налей масла в переднюю втулку.

@NegroM-ff4up 5 ай бұрын

como aser ese coso que tiene mucha potencia

@javielo1974 3 ай бұрын

I have the same problem but mine also hot broken the direction switch, the red plastic piece that switches between forward and reverse. I cant find the spare, anyone knows where to buy it??