Wow! You make it look so easy. I'm in the middle of a cabin build. Thanks for the free training! 🤠 🇬🇧

Finally, someone who knows what to do and how to do it correctly. Very good explanation and detail work! A+

Looks good. When cutting those corners, if you cut one side at 45 and leave the other one at 90, it’ll still look like a mitred corner but no risk of having any gap there. Rare that a corner is exactly at 90 degrees.

Thanks for the video it helped with my project!

Fine craftsmanship sir , great detail .

Thank you for this. Very helpful!

Thank you for this video! No garbage and you show and explain things very clearly!

I use my big snips too , instead of setting up a saw or table . My first job was vinyl siding and I would cut the whole house with snips so when I do a little soffit, you can chop them up pretty quick especially if it’s vinyl.

Fantastic video. I'm diy on my old house, and this is good rehash

Yup that’s me. Yelling at my dog to “get over here”! Nice work

Nice job 👏

That is some fast hammering!

I never cut 45 twice on the corners.I cut 1 45 and 1 straight cut and let 45 overlap when I bend the corner of fasia 🤷‍♂️ good video though

Good work Joe... Lol. 👍

great video

Very nice job bud and great tutorial on how to do it .I think I'm going to do it this way, Cheers!

Looks great 👌.

Needed this video..my guy was having trouble the other day..this will put him on point.just did a total rebuild of the porch roof of a older house.it looks good but the devil is in the details when u want to make the neighbors jealous

You could've ran your fascia all one piece wrapping around your soffit box without cutting that short piece, also instead of cutting (2) 45 cuts for your bends cut (1) 90 and (1) 45 closes it up better looks nicer.

Thanks for the video! I'll be starting a garage build soon and have been trying to figure out all of these little details that make it come together.

Nice attention to details, again! One advice if I can. You put soffit on the lean-to. It might be inviting for critters like squirrels and birds. I had this issue with my previous lean-to wood shed. I can see you had your toque. So it was getting cold! I was bout to forget... Congratulations for the upcoming 1000 subs! Thanks for sharing Corey!

Nice work.

How's she goin'? Nice job on the soffit. I'm used to vinyl but with the aluminum you can cut and bend a lot easier. I see you barn is coming along good. You already have equipment stored in it!!! It's a big barn, but soon will be too small!!! Take 'er easy!!!

Thanks for the lesson!

Nice Vedio. Do you know what type of contractor does this kind of work? I have part of both soffit & Fascia blown out with storm and framing is rotten. I need someone to repair in the house but not sure who to called?

Which edge on the F channel did you follow, with the snapped line being the (bottom of fascia board) top side of the soffit. I just did one and I had to snap the line about .625" higher than the bottom of the fascia board so I could put the top edge of the F channel to the chalk line. It seems like if the snapped line was at the same level as the bottom of the fascia board you wouldn't be able to see the chalked line because the F channel would be covering it. Maybe the F channel you used was different than mine. Mine had the slotted holes for nailing in a strip above the channel part of the F.

Do you have any tips on cutting the mitered wood framing? You show it already cut and installing it

Good video. What size brads are you using to nail the soffit to the facia board?

Why don’t u make ur own fascia? When U make it out of coil it looks so much better.

Never use treated wood under aluminum it causes problems down the road

I wish I could swing a hammer that fast

Good luck repairing that soffit material....you used nails to hold it in. I don't think you're suppose to nail soffit in....it slides in. You can't take it apart now. I have to repair lights in a soffit ....how would I take what you did apart? Try puttig the faciar on first and sliding the soffit sheets in....this way I can use a zip tool to make small repairs.

Which gun do you use for the soffit?

What is a level for?

Wow I bet woodpeckers come out thinking its a mating call.

What gauge steel is your roof and siding? Great videos

What kind of drip edge did you use on your eaves?

the fascia that you used , where did you get it?

These really are low quality construction materials that fade and get easily damaged. Bugs and vermin make homes behind metal - use Azek, etc. Better to make it look beautiful, strong and seal against bugs&vermins.