Brake pressure sensor replacement Volvo D13 ABS/TC/ESC

No video

Brake pressure sensor replacement Volvo D13 ABS/TC/ESC

Рет қаралды 64,766

Valeriu Moscalu

Күн бұрын

Replacing the brake pressure sensor nr.1

Пікірлер: 50

@saga2760 2 жыл бұрын

Can this censors also disable the cruise control ? I have ABS/TC Lights on and no cruise control. Thanks for the video

@aaj8846 Жыл бұрын

I'm having the same issue, if u got fix, what was the problem.

@saga2760 Жыл бұрын

@@aaj8846 We give up and just left it alone, sorry.

@jimjim6803 Жыл бұрын

Abs sensor most likely

@greenearth3356 4 ай бұрын

@@saga2760 Hi. Have you fixed ABS/TCS problem yet?

@user-lt7gn6jd9x 5 ай бұрын

"Classic" 😍...

@oj7724 3 жыл бұрын

Please assist me with this problem. Got a problem with modulation valve on the diff changed it's still insisting on the right side modulation valve. Got this error mid 136 Sid 12 fmi 14 on a volvo truck. Euro 4 with D13 engine Thank you so much

@KenworthPiterbiltovich 4 ай бұрын

What’s the diagnosis computer you use? Do u mind to share a link to buy it?

@joserosas1016 3 ай бұрын

I have issue when u press brake abs light on dash on then release and goes off

@keyandaneshmand9915 Жыл бұрын

Hello mister, I have 2013 Volvo my left front drive axle abs is locked up the wheel, but its spinning when its up to floor, the rest wheel are spinning what is the problem could be , thanks for assistance 😊

@valeriumoscalu7580 Жыл бұрын

What do you mean is locked? When you press the brake is locking the wheel?

@juancarlosdelrio8801 2 ай бұрын

Pirde precios en la marcha baja precios en el diésel

@user-zi8dn5mv2e 8 ай бұрын

Thank you sir ❤

@juancarlosdelrio8801 2 ай бұрын

Problemas con DSN 1045 Volvo d13 2014

@EdwardCibu-hk7cz 4 ай бұрын

What program you using to calibrate?

@g2000a 6 ай бұрын

Is this sansor an effect at transbicion?

@fernandosanz8024 Жыл бұрын

can a air leak on this pass through valve cause the ABS and TCH light to come on?

@KalchykDen 3 жыл бұрын

Did you do brake calibration in PTT after you installed brake switch?

@valeriumoscalu7580 3 жыл бұрын

Yes I did but without PTT , just turn ignition off turn it on and immediately press the brake pedal all the way and hold it until all brake solenoids will do a self test, after release and you should be good to go!

@gapurbegnazarov6158 Жыл бұрын

Where is your place located bro?

@hassanourahou6932 2 жыл бұрын

Thanks for this video .where do you have your shop ?

@valeriumoscalu7580 2 жыл бұрын

Tacoma / Washington state

@valeriumoscalu7580 2 жыл бұрын

You welcome

@namcher 8 ай бұрын

Добрый день. Я поменял брейк сенсор этот и сделали коллибровку но все равно на ходу срабатывает тормоз или hill stat assist после зажигаются все сайны и трак едет без проблем. В чем может быть еще проблема?

@KenworthPiterbiltovich 4 ай бұрын

Починил? Такая же история началась

@tait4613 Жыл бұрын

Hi sir. I have volvo truck 2016. No I have a problem with my airbags. They are going up and down during the driving. Especially when I am going down the hill pressing brake or turn on engine brake but sometimes going without it and going up after sometime. I have changed air dryer, air compressor checked all the leaks, pneumatic level sensor under fifth Still same problem. Can it be because I didn't do calibration for the level sensor or not?

@ahmedshahzad4133 2 жыл бұрын

Sir my truck volvo fh440 model 2018 is problem some time give wrong Truck Brake failure 10 ...O.....15 seconds finish wrong

@TheDwhales 2 жыл бұрын

Try to pull the senor out how did you do it???

@valeriumoscalu7580 2 жыл бұрын

Its the same way like you removing air line from a quick connector fitting! Make sure you don't have air pressure , press that black o,ring and while holding that I,ring pressed pull out the sensor!

@TheDwhales 2 жыл бұрын

@@valeriumoscalu7580 not sure of which quick connection your speaking of?

@sanjinhadzic8731 6 ай бұрын

What is the part number?

@Notmypresident2024 8 ай бұрын

How do you calibrate

@marcusrutledge8885 8 ай бұрын

Just need to replace it then air truck up and hold the brake pedal down for 10 sec ENGINE OFF KEY ON

@vadymraisa1 7 ай бұрын

How to do calibration ?

@valeriumoscalu7580 7 ай бұрын

Start the truck, leave the air compressor fill the system until it's full! Turn ignition off, press the brake pedal and hold it, turn ignition on while holding brake pedal pressed, wait until your hear all solenoids doing self test around 10-15 sec, after release brake pedal and you should be good!

@omerbayrak1808 2 жыл бұрын

What is the error code for this ?

@eugeniujosanu279 10 ай бұрын

Going thru this stuff myself .. the code is : Component - ec- advanced abs Description- miscellaneous, stop lamp switch defective (flash code 12 - 2) Look up code: SPN 1045