Very nice, I’ve been in the foundry business for over 44 years, you have a great understanding of of what you are doing….. your common sense goes a long ways….. I enjoy your videos…..
@bross8242 жыл бұрын
Another good source is myfordboy, he doesn't say much, but he is an excellent teacher!
@Preso582 жыл бұрын
I have been a fan of Myfordboy since I got started in metal casting. In fact, it was his videos that convinced me that it might be possible to have a go at foundry work. Since then, I also stumbled on the work of Olfoundryman and Luckygen1001. Both of them are Aussies like me and although they have different philosophies on foundry work they nonetheless are very experienced and there is always something to learn. Regards, Mark
@bigoldgrizzly3 жыл бұрын
"I can never find the thing that does the job best until I find the ones that don’t.” ― Thomas A. Edison Sticking with it is the only way to improve - great work mate !
@Preso583 жыл бұрын
Thanks. I must say I am a stubborn sod and I will tend to stick with a project long after others would have seen the light and walked away. In this case it paid off and the plaques have been out in the weather for a couple of years now and they still look great. They will outlive me. Regards. Mark
@bigoldgrizzly3 жыл бұрын
@@Preso58 < They will outlive me.> These days, I seem to get the same thought about all my projects...... :>))
@clayz12 жыл бұрын
I always learn plenty when watching your vids. Well, it’s 4 AM, off to work. Have a good day!
@DennisHicks787492 жыл бұрын
Cool vid, thanks! I love the safety talk, many posters leave that out. It might be good to advise folks to only wear natural fibers when working with heat as man made fibers will melt onto the skin causing serious burns.
@grassroots9304 Жыл бұрын
Nicely done. The detail of the brass cast standoff for the offset braces was an amazing bit of attention to detail. Those cross brace tie plates are a brilliant idea and nicely executed.
@bigcoolviking Жыл бұрын
Great to see you you using a crucible now rather than a crooshable, its makes all the difference.
@badbutch53524 жыл бұрын
Great job. Thanks for the trials and errors. It's always a learning process with different casts. Thanks for the video.
@fredwild1903 жыл бұрын
I noticed the gating on the second attempt in fact was not the same as in the first attempt. The side channels on the second attempt followed a much more gradual curve into the mold (10:38 vs. 25:30), and I wondered whether the difference contributed to the successful second pour. Really excellent and fascinating video. Thank you very much.
@Preso583 жыл бұрын
Who knows? That is the trouble with this type of project. If you change more than one variable you never really know what contributed to the success of the casting. I do know that gating, venting and metal temperature are fairly critical with brass. Regards, Mark
@shauna2603 жыл бұрын
Found your channel the other day and have been watching your videos since. So nice to see a humble gentleman working. And finally someone who knows how to call a “rule” I’m learning a lot from you. I’m learning a lot from you, mistakes and all. Keep safe!
@Preso583 жыл бұрын
Welcome aboard! Regards, Mark
@icedragongamer46463 жыл бұрын
Thank you Mark for your inspiration and showing us your knowledge. It's not easy. I had a good teacher who worked in foundry and I made a load of stuff and showed us what we could do with ally and brass. He gave us confidence in casting and welding..... at 15 years old 40 years ago. Can't do it now h and s at school. It's a loss to the kids nowadays. Shame
@Preso583 жыл бұрын
We were forbidden from doing any foundry work at secondary school level. The primary reason given was the classrooms had wooden floors but even after the education department devolved responsibility for WH&S to school level, and we had an engineering shop with a concrete floor it was still considered a stretch to be doing anything with molten metal. The other issue was the timetable structure. Our classes were between 50 and 70 minutes which was never enough to prepare a mould and melt the metal. Even when I was studying at college, the closest we ever got was to do some elementary lost wax casting. That's probably achievable in a secondary setting since you can make up the wax patterns, do the investment and burn out the mould over several lessons and with a centrifugal casting machine and oxy acetylene you can melt small quantities of pewter or zinc based alloys pretty quickly. Regards, Mark
@popo541311 ай бұрын
Now this would have to be the neatest and best-looking Furnas I've seen (I have watched you biled for it )
@Preso5811 ай бұрын
I like the rebuilt version of my furnace. I have also recently converted it to burn diesel fuel and it is now about three times faster than the propane version. Regards, Mark
@AlbiesProductsOnline5 жыл бұрын
If the gate is deep enough to allow the full amount of metal needed to fill the mould before the sand can cool the metal enough to stop it from flowing you can use one larger gate the best KZfaq channel for this is Myfordboy
@ronjones19905 жыл бұрын
Terrific project from beginning to end. We learn from our mistakes.
@robertgilmour19035 жыл бұрын
Really enjoyed this demonstration video. I don't have the space to do this but I am extremely grateful for people such as you which allows us to live our dream one step removed. I hope you weren't an English teacher in a former life because I'm not the best at putting things in black and white.
@Preso585 жыл бұрын
Robert, thanks for the feedback. I was actually an Industrial Technology teacher. When I started back in 1978 we were called Manual Training teachers, then Manual Arts. The name change to Industrial Technology was a political one but we we were mostly known as ManArts. Towards the end of my career I was told that all teachers are English teachers which was a bit of a cop out by the real English teachers who were copping a lot of flak about falling literacy rates. Sort of like spreading the blame. For what it's worth your communication is perfect. You use punctuation and capitalisation which is a long way from what large portions of the online community can manage these days. 😁 Regards, Preso
@lucwybo5 жыл бұрын
Setbacks and happiness are sometimes close together. The keeper always wins and with a stunning result. The work was very successful. I would go to a bell foundry in the area for such castings. This can save me a lot of work, make casting tools and furnace, collect the right materials, etc.
@Preso585 жыл бұрын
Yes, despite the setbacks, I still felt good about the result. I always imagined that metal casting at home was going to be way out of my reach. As it turned out, the very first casting I did turned out to be serviceable and I still use it in my home shop. It was a lathe driving dog. Thanks for the positive feedback. Regards, Preso
@icedragongamer46463 жыл бұрын
Hi Mark I read a few comments and replies. Using an oven is too much for for the whole mould. Preheat and slightly dry out the faces of the mould with a blow torch just before you pour the molten metal then you drive off a little excess moisture you can do this by playing the torch or blow lamp down the pouring channel for a few minutes then pour the metal straight away. I've done it successfully but finer work I use lost wax and cast plaster then burn the excess wax out. I hope this helps nice work. I like the furnace and design of your gas jet 👌👍😀
@Preso583 жыл бұрын
Thanks for the feedback. I think my furnace is just about at it's upper limit when melting brass. The refractory is capable of the temperature but the burner is probably just about maxed out. I am in the process of designing a burner that will use diesel fuel and I am hoping that this will reduce the melting time for brass and bronze. I did those brass casting quite a while ago and I thought I had learned a lot about casting since then but just recently I had the same experience with aluminium. I got a bit cocky and didn't bother to check the temperature of the melt with a pyrometer that I had made since the brass casting debacle and I got a similar result. I have always been a bit wary of drying out the mould using heat since I am concerned that it will loosen the grains of greensand which may wash into the mould. Petrobond and coolset might be different but I don't have access to those products. I still have a lot to learn but it's fun trying. Regards, Mark
@AmateurRedneckWorkshop5 жыл бұрын
You can be proud of the bridge and the brass casting. Well done.
@sheph7ceo7995 жыл бұрын
Beautiful bridge and brass plaque! Well done. Thank you for the excellent video series.
@GadgetBiker5 жыл бұрын
I think the little flaws give it some real character. Great Job!
@frikkiesmit26953 жыл бұрын
It came out very nice!!! If one wants it 100% perfect you must do it with cnc milling. For casting i give you 10 thumbs up
@Preso583 жыл бұрын
Thanks for that. It's just my view, but a casting seems to have a little more soul than a CNC machined plaque. Regards, Mark
@frikkiesmit26953 жыл бұрын
@@Preso58 exactly my view also. I agree with you. The reason i made the comment, was to try and uplift you. Cause hey nothing always turns out 100% perfect.
@MrCeez13 жыл бұрын
The Power of Patience and Determination
@Preso583 жыл бұрын
I must say I am a bit short on the patience thing sometimes but I have endless determination. Some people who know me well will tell you that I keep going long after most would recognise a lost cause and move on. Regards, Mark
@messageweek3 жыл бұрын
I've learned a lot. Having cast aluminum, and wanting to see what this looks like in brass, I appreciate the process, errors and experience gained, and I think this will be helpful in the next project. (I also appreciated that this video is done by a fellow Aussie.)
@tykellerman63844 жыл бұрын
If at first you don’t succeed try try again definitely applies.... nice work🤠👍
@johnhewit58845 жыл бұрын
Excellent series. Great filming. Great narration. I learn something every time. Thx.
@geneelliott32305 жыл бұрын
My casting group has found that all air should be pulled inside the burner so recommend closing off the excess air where it goes thru the hole around into the furnace. this will increase the temp in the furnace so metal will flow more easily.
@Preso585 жыл бұрын
Gene, that sounds logical. I must try that. Regards, Mark Presling
@dan5her5 жыл бұрын
They also use bentonite clay to increase the clay content of very sandy soils, helps retain moisture for plants I believe
@scroungasworkshop46634 жыл бұрын
Hi Mark, Stuart from Canberra here. Mate, I feel your pain as I had exactly the same problems. My first big or proper cast was a handle for a very old Atlas arbour press and my main issue was getting the sand mixture right. I had to redo the moulding six times before I could get the cope and drag to separate well enough to make it usable. I nearly quit as well but got there in the end. I learned a lot from “old foundry man” and also Myford Boy. I was only dealing with aluminium and the first cast came out well enough. I have a lot of brass and copper scrap I want to cast so I am going to order the proper casting materials next time. I also have a channel now if you’re interested. Scrounga’s Workshop. Cheer mate, Stu.
@Preso584 жыл бұрын
Stuart, I just watched your video on the Atlas press. You did a really fine job and it looks original despite the aluminium handle. The pattern making looks excellent as well. I am glad you persevered with the moulding process. Getting that right is the key to the rest of the process. For what it's worth, I still have to redo castings which fail due to poor gate design or improper placement of vents and risers. Having said that I have seen much more experienced foundrymen who suffer the same problems. Part of the issue for DIY casting is that just about every casting is a prototype and if you were to pour the same casting 100 times you would soon work out the ideal workflow and method. I am looking forward to seeing more of your work. Regards, Mark
@scroungasworkshop46634 жыл бұрын
Mark Presling. Thanks Mark for your kind comments and encouragement. You hit the nail on the head with every job being a prototype. I do enjoy the casting process and so want to do more. I think my biggest mistakes was my choice of materials. Like you I found talc to be pretty unsuitable as a parting powder and I think my clay was wrong so as I said I’ll be buying commercial clay and parting powder. I hope to be getting more restorations going now, as I may have told you we had a serious car accident which really slowed me down but I’m starting to get back out into the work shop now only to find I have a water leak which is flooding the floor so I’ve had to clear out a lot of gear to to fix it. Anyway cheers and thanks again. Stu.
@seancrowley75203 жыл бұрын
Nice job and thanks. Lots of useful information. And now for my opinion (yes, everybody has one). I would fasten the badge to the bridge so that it could be viewed whilst standing on the bridge as opposed to standing, say in a river basin... thanks again.
@Preso583 жыл бұрын
Well, more than one viewer has made that observation but I can assure you that the plates are quite easily read from the banks of the creek. Regards, Mark
@garycooper49643 жыл бұрын
Mark I think they turned out GREAT especially being second attempt with brass. As like all craftsman we are much more critical of our own work . I have been thinking about building new forge and think this is the perfect size after watching this build 2 or 3 or 4 times atleast . LOL Thanks for sharing
@markphillips5368 Жыл бұрын
The higher metal temperature and the extra ingate solved the problem of the cold shut on your first attempt. Topping the riser up with molten metal once the mould has been poured also had the advantage of adding extra molten feed metal to make sure the casting fed properly.
@Preso58 Жыл бұрын
I now have a decent pyrometer which allows me to check the metal temperature more accurately. I often get a bit impatient and try to pour too early. Regards, Mark
@davidfe475 жыл бұрын
Wonderful in all aspects. Glad to see you plated your furnace. Great explanation of you burner. Far simpler than most om uTube. The sight & sound tips are easily repeatable. Name plates are the perfect touch. Can't wait to see the dedication.
@RockingJOffroad5 жыл бұрын
I think these castings came out wonderfully for a first time casting brass.x
@Jason-rs6co4 жыл бұрын
good job mark good to see your not scared to share your mistakes more learnt that way i think. in fact if your ever down newcastle i might even let you build me a bridge. im good hearted i know
@Andrew-qo6br3 жыл бұрын
Nice job. BTW, you learn from your mistakes. We all want everything to be 100% perfect the first time - life just doesn't work that way. Thank you for showing what to do and not to do so we can learn along with you, thank you.
@ruperthartop72025 жыл бұрын
Well done. I used to cast Lead grids for batteries 0.020" thick. Its all about a steady smooth pour, letting the air escape and the correct pour temp. Looks like the same applies to brass. Great video thanks
@Preso585 жыл бұрын
That sounds like a real challenge! I must say that by the time I got around to pouring the metal my heart rate had just about doubled. I don't know if it was excitement or just sheer terror!
@ruperthartop72025 жыл бұрын
I went on a casting course last year and poured some brass. You can really feel the heat!!
@bobvines005 жыл бұрын
Mark, Your brass nameplates came out surprisingly well for your first two handful of pours. I suspect that many are trying to figure out why it took them so much longer to get good results like yours. Keep up these great videos!
@Preso585 жыл бұрын
Thanks Bob. If I had not done the previous video on the pattern making I think I would have given up and just done it in aluminium. It was good to know that my new furnace can handle brass and I am guessing, copper and aluminium bronze.
@jrkorman5 жыл бұрын
Excellent - Those plates certainly dress up your bridge nicely.
@lv_woodturner38995 жыл бұрын
Very nice results. A lot of work and patience to overcome the failures. Looks very good. Casting metal is not easy. I have watched videos like this, but not tried myself yet. I think if I try it would be aluminium. Dave.
@ianpendlebury37045 жыл бұрын
Triumph indeed......an excellent result and an informative video.
@TomMakeHere5 жыл бұрын
The name plate looks great! I'm definitely going to have to get back into casting. I might need to copy your setup somewhat!
@OldMachinery5 жыл бұрын
Great job on the bridge, foundry and nameplates
@pgs85975 жыл бұрын
G’day Mark, excellent series on the bridge and foundry furnace. Olfoundry man has many excellent videos and many years of knowledge in the industry. Well done with the plaques it must have taken some time to make the pattern, I hope the better half doesn’t go looking for the brass fittings. Cheers Peter
@mce1919A42 жыл бұрын
Nicely done thank's for sharing this.
@Vladviking5 жыл бұрын
Relatively exhausting work pounding sand and carrying the flask around. I don't neck the riser as it just cools off faster and blocks the return of metal that you want. I might have used 2 risers, one on each end. And maybe not tried to run the filler tubes so far out as that would cool off and shut down fast too. I tend to believe one or two big entry channel/s is better than many small ones But there is a thousand ways to success in casting. Great video and results.
@lloydmilton5 жыл бұрын
an interesting video giving some really good advice on how metal flows into a mould - covers gate size and there is another video this guy does with Bob Puhakka where he discusses the sprue velocity etc all in all worth the watch IMHO just for the information given which all ties into the reasons behind having a pouring basin mate
@CapeCodCNC5 жыл бұрын
Very nice! Watched the furnace build, I may do this when the new garage is built!
@Preso585 жыл бұрын
Thanks for that. I must say that I had always thought that any sort of metal casting would be too difficult to do successfully at home but it's not the case. I was really surprised when the very first casting I attempted turned out to be useful and I still use it today. It was a lathe carrier for between centres turning. I used a split wooden pattern and cast it in scrap aluminium. The new furnace I made is a vast improvement on the original one. I didn't put a lot of effort into it since I thought it would probably fail! Regards, Mark Presling
@geneelliott32304 жыл бұрын
If you close the gap around your burner it would increase temperature and speed up the melt
@IBWatchinUrVids5 жыл бұрын
For anyone who cares about this stuff, bentonite clay can be purchased from well drillers. I have some, but so far I prefer casting into petrobond sand. I purchased mine on ebay. I mainly cast aluminum.
@davidtaylor61245 жыл бұрын
No question - it was worth it! Great result.
@Preso585 жыл бұрын
Thanks David. I have finished completely now and they are up on the bridge permanently, and the creek started flowing last night!
@garyk53163 жыл бұрын
Dont consider them fails...just learning experiences. Good job.
@joell4394 жыл бұрын
👍👍😎👍👍 - i'm late..... but so glad these awesome videos are still available so i can catch up 🤣. Mark, Awesome work my friend...... Joel
@icedragongamer46463 жыл бұрын
There was a little trick as well get a fine needle around the depth of the upper layer of the mould it would help the steam from the sand excape thus on long plate casts it would allow the metal flow better. Have a go and let us know
@andrewdolinskiatcarpathian3 жыл бұрын
Fabulous result. Well done for your perseverance. 👏👏👍😀
@icedragongamer46463 жыл бұрын
Hi Mark yes probably that I was using a higher clay content sometimes I let the mould dry out naturally but I think there may be too much water content in the sand. When I did it for the first time it boiled and shot the aluminium out of the mould luckily not high enough and I was heavily protected. I tickle a blow lamp over the split mould just to dry out the surface and warm up the mould a bit I'm definitely watching how you get on love your work. I just hope that anything helps. It's a bit like cooking a cake a little bit of experimenting to get it sorted
@Preso583 жыл бұрын
It's fair to say I picked up the metal casting bug fairly late in life. It was deemed to be too dangerous to include in the high school metalworking curriculum here in Quensland and I notice that Mr. Pete often talks about teaching metal casting during his education career. I do learn a bit more every time I have a fail but it's not my main gig so I might only get the foundry gear out 10 times a year. Regards, Mark
@nongbloke3 жыл бұрын
@@Preso58 A dictum for makers - if you don't make a mistake, you don't make anything. Mastering any new task is an iterative process - that's why they call it trial and error. Good to see you having a red hot go (boom, tish). Love the job you did on the forge. I spent a bit of time lost wax/centrifugal casting silver and gold fifty years ago, but based on your experience, I reckon I'll leave brass alone. Cheers, Bill
@CMAenergy5 жыл бұрын
Just a little something to try, Looks like you got gasses backing up an slowing the flow of pouring, When you are pouring such a long an flat piece, Sometimes I make an entrance into the cast from one end an let the metal flow up hill. ((Not from the middle)) An I never made my puddling hole at the top of my sprew (spelling ? it's been well over 25 years) (I forget which is the drag an cope) PREHEAT THE MOLD BOX IN THE SAND I would make the puddling pool in the drag or the bottom mold box so the metal has slowed down closer to the cast. an the velocity of the falling metal an contaminates will be driven into the bottom drag where the pool is an stays warmer, where as if they are falling from the top out of the pool, an the molten metal will not have enough time to rid itself of all the air an gasses that are picked up, including sand as it falls, when it settles into the drag pool, the metal flows in a much better pour with less gasses, an I also make a couple of breather holes from that pool an the top flat of the cast as to allow all gasses to escape, use welding rods several of them. Also remember to preheat the mold, (very important) by some times if you can place mold on top of the furnace, (yours is to small) this rids a lot of humidity from the sand, But rather then using wet green sand I would use water glass, an not using co to harden it, just preheat it in a simple oven then remove the mold from the mold box, after it is hardened, also when pouring try to keep one point of the mold box lower then the other so the metal flows up hill, an not so flat, as this can cause defects (gas pockets) in the casting, it also cools. I would also put welding rod holes (4 or 5 of them) in the top mold box to allow venting as the metal is being poured, other wise you will get to much humidity an back pressures. re the flame make it carbonizing, After seeing how you mounted it, I would have placed a adequate breather hole (probably 1/4 inch rod) where those bolt were going to be, an this would have allowed me to thread a nut onto it without having to do other work,
@evdoby5 жыл бұрын
Turned out very nice. Well done.
@bclare25445 жыл бұрын
Another informative series Mark,well done.
@popo541311 ай бұрын
Hint door knobs are the most dangerous door laches? In a fire they become too hot to handle. Lever-type laches are the safest as you can use your elbow or any object to knock them open (such as a coat hanger) and pull or push them open
@HepcatHarley4 жыл бұрын
Great job, I just hope nobody steals them for the scrap value. :)
@iteerrex81665 жыл бұрын
A very nice finishing touch for a well done project! How about a turning handle for the lid? Really like the foot lift tho.
@a0cdhd4 жыл бұрын
Aaaarrrrggghhh. I have been searching high and low for brass door knobs. Tried at least a dozen antique shops, hardware stores and other unlikely places without success. Even tried places on my way from Briz to Adelaide a year or so ago.Eventually gave up and settled for old steel ones. And here you are melting the damned things down.
@Preso584 жыл бұрын
I must say the brass knobs looked great when we first got them but they soon start to corrode under the clear powder coat they put on them. They get these hideous brown spots and it is difficult to polish the brass again because the powder coat forms a really hard skin over the corrosion and tarnish. If I had a maid I could pay her to polish my .... no, I better not say that out loud! Regards, Mark
@mountainsprings33034 жыл бұрын
Great job Mark, thanks for sharing.
@BogdanSzczurek5 жыл бұрын
You, sir, secured my like with the opening song :}
@ronaldnickell61103 жыл бұрын
When making your green sand, just get a bag of clay kitty litter. Don't bother with getting the lumps out, just add water to make a slurry that you mix the sand into as you will need the water anyway. This simplifies the process, and will give the same results.
@Argyll98462 жыл бұрын
Having worked in a foundry many years ago I'd guess that a riser/channel at either end of your plate may have been of some assistance to the brass flow, but on the whole it turned out well.
@Preso582 жыл бұрын
Thanks. I learned a lot from that job. I now use a temperature probe to check the melt and it has saved quite a few castings. I upgraded the hot end of the probe just today. I added a stainless steel heat shield to protect the wiring. Regards, Mark
@yambo595 жыл бұрын
A beautiful job all around an excellent bridge, so much attention to detail and well engineered - hope those plauques dont walk off some day--lol
@Preso585 жыл бұрын
Thanks, I keep wondering what the scrap value is for brass these days!
@itanc1 Жыл бұрын
Nice work dood!
@willywgb5 жыл бұрын
Well done. Very nice job. Cheers Willy
@jamesmillard2595 жыл бұрын
Enjoyed the series!
@Watchyn_Yarwood5 жыл бұрын
Thank you for another great and informative video! Well done!
@Preso585 жыл бұрын
Thanks William. Someone asked me a while ago if I could cast brass and without really thinking about it I said yes. He then showed me the job that he wanted done and given my recent experience I'm afraid I would have disappointed him. Luckily the job didn't go ahead. It's OK to fail when you're doing your own work but I hate not being able to deliver when you're doing it for someone else. Regards, Preso
@Watchyn_Yarwood5 жыл бұрын
Are you going to enter the casting/machining/3D printing competition - kzfaq.info/get/bejne/bp2EfZd_mZnZYZ8.html @@Preso58
@crazyfeller57045 жыл бұрын
Outstanding work. Thanks for sharing, always good quality content. You should have a lot more subscribers....nuff said.
@Preso585 жыл бұрын
Thanks, I must say, I don't get the whole subscriber thing. Although, there was a time when I thought I was doing well with 30 subscribers! I guess it will build over time but for me, it's more about archiving what I do. I find it weird that people will now have a sort of digital afterlife. Unless there is some sort of zombie apocalypse my videos will probably live on after I've put my cue in the rack!
@iknownutting4 ай бұрын
top job i learnt stuff ty
@icedragongamer46463 жыл бұрын
I could save you a little energy. Have a little basket over the exhaust so that you can preheat the scrap. I don't know if you preheated the mould it could dry out the sand thus the molten metal wouldn't loose so much heat drying out the sand and flow better. Just a thought
@OldIronShops5 жыл бұрын
Nice looking parts well worth the effort
@lourias3 жыл бұрын
Nice... thank you for sharing.
@johnnym13205 жыл бұрын
very nice! keep the projects coming
@garagemonkeysan5 жыл бұрын
That turned out great. Thanks for sharing. : )
@yvesdesrosiers23965 жыл бұрын
G'day Mr P. Looks good. Thanks for sharing!
@Preso585 жыл бұрын
Thanks Yves.
@jamieclark72214 жыл бұрын
Great Job, Try covering the top of your furnace and you will not use as much gas. If you watch your video you can see how much heat you are loosing at the top.Just cover half the top don't cover the entire opening.
@petersaupe74554 жыл бұрын
Well done.
@AboutTheBuild5 жыл бұрын
Looks really good 🇦🇺🇦🇺
@mclem4u5 жыл бұрын
Good job!👍
@kentuckytrapper78011 ай бұрын
You will use five time more gas without a regulatory, don't ask how I no,lol ,great video..
@Preso5811 ай бұрын
I am now using diesel as a fuel and it is a lot quicker and cheaper than Propane but I get your point. My old propane burner did the job but it was very inefficient. kzfaq.info/sun/PLbPzkHRZCQB_E95Rz3PKZzTDwYy3MTlTr Regards, Mark
@THE_PeglegSwantoon5 жыл бұрын
Another possible reason for the premature solidification might be due to the flask being cold, I read in "Welder's Bible", at least I think it was that you want the flask to bask in the heat of the furnace
@Preso585 жыл бұрын
I poured that mould on one of the hottest days of the year and I guess I could have put it out in the sun for a while. Not sure where you live but our summer got to 35C in the shade. I guess it is all about temperature gradients though. The less difference between the molten metal and sand interface the better. I just recently made a pyrometer which can measure to 1000C and I used it to do a difficult casting in aluminium. The casting came out perfectly so I will be checking my metal temperature more carefully in future.
@THE_PeglegSwantoon5 жыл бұрын
@@Preso58 I live in Minnesota, in the States. We don't really get as much 'stable' heat like you, our temperatures vary quite a bit more, basically +40 C to -40 C on the extreme ends. 😉 The book I read that from ( nearly positive it was Welder's Bible) was talking about casting Iron, but I remember they were saying that you should have the flask close enough to the furnace so that the extra moisture in the sand cooks off while it preheats the sand
@theanvil52885 жыл бұрын
Well done ✅...👍🏻👍🏻
@thomasutley5 жыл бұрын
Such a great informative video series. Congrats on the finished product!
@Preso585 жыл бұрын
Thanks Tom. I painted the backs of the plaques with the same orange paint as the bridge. I'm already planning the opening ceremony! I've been meaning to ask you if you don't mind, do you carry out your work with plaque making and metal etching as a hobby or is it your job? Or are you one of those lucky people who have turned your hobby into a paying job? Either way you get professional results. Regards, Preso
@thomasutley5 жыл бұрын
Mark Presling Sadly, I still have a full-time day job that consumes most of my time. My home shop projects are just a way to exercise my creative side after spending my days focused on navigating corporate processes for a few more years yet. If I thought I could support my family doing the Maker work, I’d have jumped already!
@Preso585 жыл бұрын
Tom, that's interesting. I will check out your link on the Instagram post. I have always been intrigued by how diverse people's hobbies and careers can be. I once employed a man to do some earthmoving on our property. He was a big, rough looking, plain talking guy but he later disclosed that he was a flower breeder in his spare time, and not just any flowers, he specialised in carnations! I am still getting my head around the whole Instagram thing and I have never downloaded a podcast but I want to give it a crack! Regards, Mark
@moonshiner29773 жыл бұрын
You need more patting on the back and less slapping :) Great job and determination !
@Preso583 жыл бұрын
Thanks. I don't normally work with brass so it was a steep learning curve. Regards, Mark
@stephenfowler41153 жыл бұрын
You could try multiple risers
@lancelottavola96853 жыл бұрын
problem is : you need larger hole for the metal flow very fast before start solidify...
@Kudzualabama5 жыл бұрын
I been watchin a fair amount of casting and a lot of em seem to run a thin rod down to the pattern before removin it to give the hot gas somewhere to go . To not get a back pressure block when it's poured . Your finished cast looks good either way , just a thought as to maybe why it was so hard to get it to fill the ends . I enjoyed the video , cheers
@Preso585 жыл бұрын
I think the main problem was the melt temperature and the inadequate gating. I learn a bit more each time I have a failure and there are plenty of them so I should be an expert in another 20 years or so.
@icedragongamer46463 жыл бұрын
I put that wrong. Use the needle to poke from the pattern side to the top of the mould from the pattern itself
@Preso583 жыл бұрын
I do use vents in my moulds a lot more now. I also have to fight the urge to ram the sand too hard since that can prevent the mould from venting. Regards, Mark
@MatthewTinker-au-pont-blanc5 жыл бұрын
Your overalls should be over your boots, a splash inside your boots could be disastrous!! Regards, Matthew
@Preso585 жыл бұрын
Matthew, now you know why my wife always checks my appearance before I leave the house. I've had some "costume fails" before! I didn't realise that I had mis dressed until I watched that footage. I was hoping no one would notice.
@MatthewTinker-au-pont-blanc5 жыл бұрын
@@Preso58 I did a lot of steel fabrication work, I adopted welders boots which have no laces, a flap over the front with velcro. No laces getting burnt! No metal making it's way down into your socks!
@AJR22085 жыл бұрын
Leather Welding Spats - check them out online. They can be short or long (go right up the shin). Try making your own but you can buy them from welding supplies - $20 to $50. Get them from China (Banggood) for less than $15.
@tommybrown90343 жыл бұрын
Top man...
@ypop4175 жыл бұрын
Nice Plaques I would clear coat them otherwise they will look like the doorknobs you made them with!
@Preso585 жыл бұрын
I have a cast brass nameplate next to our front door (an original, must be around 80 years old), it would get that brown oxide coating on the raised letters. I tried spray on metal lacquer and clear powder coat and it invariably fails after about two or three years. The clear powder coat is better but there are always tiny pores that allow oxygen and moisture to get through. Once the deterioration starts, it leaves little tracks of brown oxide like veins under the coating. You then have to remove the clear coat, re polish and re-coat. It gets worse if the metal is exposed to UV light and rain. I figure that I can just sand the exposed letters lightly with a fine abrasive every now and then. Just what I need, another maintenance issue! 😁
@Kevin-gx8lc5 жыл бұрын
Ha ha... when you lit up that furnace to cure the cruSHible, it was like 'SHweet SHoul SHounds SHtirring my SHoul ! Great build Mark, brilliant vid. Thanks! Greeting from Southport UK (or is it SHouthport...?!!).
@noellwilson12734 жыл бұрын
Spray paint the gloves with silver/aluminum paint to cut down on the radiation transfer. Or buy commercial products for much more money.
@Preso584 жыл бұрын
Noell, I am hoping I won't have to cast much brass in the foreseeable future. It takes forever to melt and the burning zinc fumes are a bit stinky. I really should get a good reflective pair of gloves though. Regards, Mark
@jeremiahmccutcheon3234 Жыл бұрын
Would you be interested in making one of these for me? My brother recently passed away and I need a nameplate for the tomstone I’m making him
@AlbiesProductsOnline5 жыл бұрын
Why do you keep putting the powder on the pattern and then brush it off the hole reason for the powder is to stop the sand from sticking you put a layer over the part and leave a later between the part and sand and a good even coat between the cope and drag