Bridgeport Mill Vise Restoration. From Rust to Restored!

  Рет қаралды 8,717

Eno Restoration

Eno Restoration

6 ай бұрын

Full restoration of this Bridgeport Mill Vise takes us from Evapo-Rust to the surface grinder and then final assembly. Feels great to bring this tool back to a workable state!
Subscribe for more restoration videos!
As an Amazon associate I earn a commission if you purchase through this link:
Scotch-Brite wheel is great for polishing and I use it frequently: amzn.to/47ppYDC
Gibbs Lubricant is great all around product! amzn.to/3sVlnds

Пікірлер: 61
@KUGW
@KUGW 5 ай бұрын
I want one of those, but I sold out to the man and bought a used KURT vise lol. Cool video, nice paint job....
@EnoRestoration
@EnoRestoration 5 ай бұрын
Thank you!
@kristyskirt9015
@kristyskirt9015 4 ай бұрын
Nice work
@EnoRestoration
@EnoRestoration 4 ай бұрын
Thank you very much!
@kristyskirt9015
@kristyskirt9015 4 ай бұрын
@@EnoRestoration you’re very welcome. No easy restoration. Take care
@gbowne1
@gbowne1 5 ай бұрын
I got mine at a rummage sale. It looked like it hadnt been used for 50 years. It was covered in about a half inch of chips, grease, rust, dirt... and of course random holes and all over it. It has the swivel base which is really nice.. not all of them stay with the swivel. I didn't pay much for it. I filled up all the holes and the drill pecks all over it. I had to grind the bed and bases smooth and flat. Yours turned out nice. I think every shop should have one if they have a mill suited for its use.
@EnoRestoration
@EnoRestoration 5 ай бұрын
Thank you for the comment and watching my channel! Next one I do I may fill the holes.
@gbowne1
@gbowne1 5 ай бұрын
@@EnoRestoration I have another in about the same condition yours was in. I should video the process. I did see an assembly diagram. The "hole" in the slide jaw casting is a small pin.that holds in the bearing bronze nut. I've never had to remove it. I originally thought it was a peck hole from a drill too.
@EnoRestoration
@EnoRestoration 5 ай бұрын
Thanks for the intel!
@jimdean7335
@jimdean7335 6 ай бұрын
That groove in the front may be a felt seal. Another nice project.
@EnoRestoration
@EnoRestoration 6 ай бұрын
A felt seal would be a good idea to keep that clear. Thanks for the continued support of my channel!
@tonyc.4528
@tonyc.4528 6 ай бұрын
Nip the sharpest part off the point of a sheetrock screw, screw it into the oiler you want to remove, then use a claw hammer to pull the whole thing out like you would a nail. It'll trash the oiler, but it'll come out. Great job on that!
@EnoRestoration
@EnoRestoration 6 ай бұрын
Ah, great idea, thank you!
@r.j.sworkshop7883
@r.j.sworkshop7883 6 ай бұрын
Since that hole in the base is so large, it would be noticeable cosmetic upgrade if you bored it out to get it straight, and then press a cast iron slug in and then deck it off. It would be an interesting side project to try, and there would be a noticeable visual improvement. Keep up the good work.
@EnoRestoration
@EnoRestoration 6 ай бұрын
That's a great idea, need more side projects,...! Thanks for the comment!
@chrisstephens6673
@chrisstephens6673 6 ай бұрын
That would have been my suggestion too, the "apprentice marks" do rather let down all the hard work. Loctite and interference fit cast iron plugs would be all but invisible if done with care.
@mounty8807
@mounty8807 6 ай бұрын
Hey Jame, if I didn't know better, I'd say you have a Vice for Vises... Not that I mind, mind you... your call for showing/admitting your soft spot... Keep up the great work, non-the-less, and keep those vids a comin'.... Cheers!
@EnoRestoration
@EnoRestoration 6 ай бұрын
Yeah, I hear you about the vise vice..., but this was an opportunistic purchase that came along with the rotary table... Its listed for sale locally and I hope to move it quickly and turn that cash into something else... I do actually have 3 other vises (a really cool 3 axis Victor among them), but I'll hold off on working on those for a while... Thanks for following along!
@veejaybomjay8145
@veejaybomjay8145 6 ай бұрын
Nice work, great video!
@EnoRestoration
@EnoRestoration 6 ай бұрын
Thanks a lot!
@mudnducs
@mudnducs 6 ай бұрын
Nice job man!
@EnoRestoration
@EnoRestoration 6 ай бұрын
Thanks!
@onehot57
@onehot57 6 ай бұрын
I have that same vice on my mill, I had to recondition it also, it was in a leaking Conx container for years.
@EnoRestoration
@EnoRestoration 6 ай бұрын
I enjoyed bringing this one back to life. And it already has a new home with a gentleman here in NH. He’ll give it a new life in his shop.
@peteengard9966
@peteengard9966 6 ай бұрын
The hole in the top of the moveable jaw should have a set screw down in it. It holds the bronze nut in. The hole in the bottom of the nut should have a felt pad to hold oil.
@EnoRestoration
@EnoRestoration 6 ай бұрын
Ah, very interesting! Thank you! This is why I love these videos, learning so much from the viewers. Thanks!
@billdoodson4232
@billdoodson4232 6 ай бұрын
I used a woodscrew to remove the old oilers from my Colchester lathe. Screwed them in and then used some combination pliers to lever them out. Do you have elephants living above you?
@EnoRestoration
@EnoRestoration 6 ай бұрын
Simple and good idea! Much better than what I did. Thanks for the suggestion and for watching my video.
@vicferrari9380
@vicferrari9380 2 ай бұрын
How did the jaw lift numbers come out? Thats what I just found with mine. I was hoping you were going to address that. I was trying to square a block and just couldn't get them parallel 😮. Your work looks great.
@EnoRestoration
@EnoRestoration 2 ай бұрын
Thanks Vic, I sold the vise before I look into that. Thank you for the comment!
@bengardiner3867
@bengardiner3867 6 ай бұрын
Did you chase the threads in the "end stop" holes off camera? Great resto despite the bufferburn. Every vise refurb has Apprentice Marks. These are pretty mild in comparison to something out of a school. Great job!
@EnoRestoration
@EnoRestoration 6 ай бұрын
Yes I did chase out those threads. The buffer burn did get fixed up nicely, but yeah, argh.....!!! Thank you!
@silverbullet7434
@silverbullet7434 6 ай бұрын
Think id add some copper anti seize on the ways and thrust washers I have a unused Bridgeport vise in my shop from back in 1975 or so.
@EnoRestoration
@EnoRestoration 6 ай бұрын
Thanks for the comment. I'm sure that vise you have would be a like a time capsule, very cool!
@MgBaggg
@MgBaggg 6 ай бұрын
Frying an entire bird like that is so foreign to me as a Dutchman. But sure looks delicious. Excellent safety precautions too. As for the grinding, you mention that it needs balancing, but did you dress it already?
@EnoRestoration
@EnoRestoration 6 ай бұрын
Congrats on being the first one to comment on the turkey fryer...! It was a first time for me doing so, but it came out great. Yes, the wheel is dressed, but I need to balance it. I have a dedicated hub that I can mount the wheel onto, just need to get a rig to balance it on. Thanks for watching and the comment!
@scootertrash3807
@scootertrash3807 6 ай бұрын
Couldn’t you use your grinder guiding side to side since it won’t cut properly lengthwise? I’m not a machinist I just see a possibility when cutting side to side. Yes, a lot of very short cuts over a wide area, yet it should accomplish the proper results, would it not?
@EnoRestoration
@EnoRestoration 6 ай бұрын
You are on the right track (looking for other solutions...). With the case of a surface grinder, the max y-axis (in and out) travel is about 6 inches. So, although I could mount the vise in that orientation, and take shorter passes, I would only be able to go less than half way in one set up. I do have other Kurt vise videos where I do use the surface grinder to clean up the ways. Maybe check those out. Thanks for watching!!
@scootertrash3807
@scootertrash3807 6 ай бұрын
@@EnoRestoration I shall check out the other videos and enjoyed this one sir
@scottkramer7431
@scottkramer7431 6 ай бұрын
I bet the bore the threads are in has an oil groove, just like the casting bore.
@EnoRestoration
@EnoRestoration 6 ай бұрын
Ah, interesting. Didn’t consider that. Thanks for the comment.
@robinhoff4598
@robinhoff4598 5 ай бұрын
Excellent video. Glad to subscribe. Clear, great pace to narrative, overall very informative. What was rust preventative you used ?
@EnoRestoration
@EnoRestoration 5 ай бұрын
Thank you for supporting my channel!
@EnoRestoration
@EnoRestoration 5 ай бұрын
I used Evapo-Rust for the rust removal.
@EnoRestoration
@EnoRestoration 5 ай бұрын
For rust prevention I simply oiled all the metal parts.
@mdavis8430
@mdavis8430 6 ай бұрын
I have the same vise, do you know if any parts are available like the jaws?
@EnoRestoration
@EnoRestoration 6 ай бұрын
I haven’t looked into that. I’ve seen some people make their own.
@ApacheRanch
@ApacheRanch 6 ай бұрын
👍
@EnoRestoration
@EnoRestoration 6 ай бұрын
Thanks!
@jimsvideos7201
@jimsvideos7201 6 ай бұрын
Whoever had it last was kind to leave the jaws open so they didn't rust up solid.
@EnoRestoration
@EnoRestoration 6 ай бұрын
All in all, it turned out ok, I think it was only outside for a limited time.
@chrisgreig5628
@chrisgreig5628 6 ай бұрын
🗜✅
@EnoRestoration
@EnoRestoration 6 ай бұрын
Thank you! On to the next project...!
@davidcummins1776
@davidcummins1776 6 ай бұрын
I will have to disagree with you here old oil smell is not loveable & neither is new oil smell. I have seen guys screw a selftaping screw in to an oiler & used that to pull them out, keep up the good work.
@EnoRestoration
@EnoRestoration 6 ай бұрын
Great idea on the oiler, thanks for the continued support!
@bennysharkey8391
@bennysharkey8391 6 ай бұрын
REALLY?
@EnoRestoration
@EnoRestoration 6 ай бұрын
YES!!!
@kellyswoodyard
@kellyswoodyard 2 ай бұрын
Probably lead based paint. Worth considering. What you very successfully did, was destroy all the history of that vice. The scars and dings, made it what it is, an antique working tool. To clean up the precision surfaces, yeah, that's fine, and a good idea. It now, as we Australians like to say, looks like shit
@EnoRestoration
@EnoRestoration 2 ай бұрын
Always good to check for lead paint before grinding it. In this case it had no paint so I was ok. And thank you for watching the video. I like to think this vise now has a second life that it would not have otherwise. The new owner is very happy with it.
@jaizanwar8227
@jaizanwar8227 5 ай бұрын
Wasting my data 🤦...not a restoration..just cleaning services
@EnoRestoration
@EnoRestoration 5 ай бұрын
Thank you for watching and providing the comment.
Very old vice restoration -  How to restore with powdercoat
26:00
restoration house
Рет қаралды 14 М.
Restore a Bridgeport Vise pt 1 TIPS #411 tubalcain
27:48
mrpete222
Рет қаралды 43 М.
Increíble final 😱
00:37
Juan De Dios Pantoja 2
Рет қаралды 21 МЛН
When someone reclines their seat ✈️
00:21
Adam W
Рет қаралды 24 МЛН
WHY IS A CAR MORE EXPENSIVE THAN A GIRL?
00:37
Levsob
Рет қаралды 20 МЛН
Old York vise restoration
29:06
Mlenski Original & restorations
Рет қаралды 24 М.
How To Plane a Bridgeport Mill Table: Part 1
52:58
Steve Watkins at Work
Рет қаралды 107 М.
Rusty BENCH VICE restoration. #rusty #tools #benchvise
22:55
Restore & Recycling
Рет қаралды 82 М.
Cursed Rusty bullet vise Restoration from 1950s
24:41
Old Tool Restorations
Рет қаралды 49 М.
Vise restoration with simple Tools (P-003)
28:25
RED Factory DIY
Рет қаралды 45 М.
Bridgebort Milling Machine [Rescue]
35:43
Hand Tool Rescue
Рет қаралды 1,3 МЛН
Restoring a 50 year old Machinist Vice
18:41
Alexandre Chappel
Рет қаралды 324 М.
Increíble final 😱
00:37
Juan De Dios Pantoja 2
Рет қаралды 21 МЛН