No video
A very annoying oil leak!
Рет қаралды 4,013
Күн бұрынSubscriptions: britrest.com/s...
/ britrest
www.paypal.me/...
Shop www.britrest.c...
playeur.com/c/...
Email britrest@britrest.com
This video is produced for entertainment purposes only and Britannica Restorations nor Michael Wesson and/or guests featured in this video shall not, in any way or measure, be held accountable or responsible for any damages related to attempted repairs as pictured in this video.
All opinions expressed by Michael Wesson and/or his guests are solely for entertainment purposes and shall not be interpreted as an official sponsorship of a product, brand, enterprise nor a judgement of quality and/or value of a product, brand, and/or enterprise.
Furthermore, Michael Wesson and/or Britannica Restorations are not responsible for the comments published by viewers of said video.
@MrBadvok 2 ай бұрын
II’m not sure but if that screw is on the suction side of the pump (while running) it will draw air in. On stopping gravity will leak oil.
@andrewmarkland9411 2 ай бұрын
Stopping gravity could be tricky
@stevengeets5729 2 ай бұрын
Have you drilled out these bolts? Conical seat in steelplate looks damaged. These bolts also need some sealing otherwise they can leak through the thread
@BritannicaRestorations 2 ай бұрын
The bolts are in blind holes
@stevengeets5729 2 ай бұрын
You are right about the blind hole. But there is no seal between the gearbox casing and the oil pump housing, so the bolt bore will fill with oil. These bolts are assembled from factory with some sealer/loctite . Thats why you have to heat up these bolts to break this product otherwise you strip the torcs
@billb3444 2 ай бұрын
The chamfer of the hole in the plate is quite large compared to the bolt so not 100% contact between bolt head and plate. Also, as said, may not be a true face on the plate. Sorry you missed evensong on this one. Suggest looking into Mr Jameson for a more in-depth answer.
@gregdyar6451 2 ай бұрын
At least now you know its a genuine land-rover rebuild with the usual leak.
@alfredsteidle5035 2 ай бұрын
I mean I see the countersink is not good. Is it the correct angle on Srew or Countersink hole ? It is going threw the thread, so why not using Loctide for sealing the thread , and maschining the Countersink hole? Also, I can see many small edges, and shaves ? Some srews are not in Line with the head, so maschine the cone a little bit. Sometimes Galvanizing is different thickness.
@davidsonsrebuilds.2426 2 ай бұрын
Just a theory Mike but that hole looked slightly ovaled to me on the backing plate... is it possible someone has chiseled the screws out after say ronding the heads off and therefore divoting the cast around the tapper for that bolt hole?
@gallois3 2 ай бұрын
Still don’t know why it wasn’t leaking while running… ah, the mysteries of working on Defenders!!
@BritannicaRestorations 2 ай бұрын
I just it is one of those things ...
@harveysmith100 2 ай бұрын
Little things like that can send a man over the edge. I hope JP finds something buckled, bent, warped or all three just so you can sleep easy.
@jamescaron6465 2 ай бұрын
If there is any opportunity for a liquid to escape it container, it will I wouldn’t touch those bolts and plates at any cost right now you got it to stop leaking and I swear if you touch it again it’s gonna dump like a sieve
@iceman9678 2 ай бұрын
Did it come in a yellow bag?
@du7ch384 2 ай бұрын
It's a landrover, it's supposed to leak 😉 Puddles of fluid tells you it still has some to lose.
@kabaottoemulsion1869 2 ай бұрын
That aluminum part must have hairline crack! But You fixed that one anyway!
@BritannicaRestorations 2 ай бұрын
You are right!
@ianwheat1577 2 ай бұрын
Looks like that cover plate been drilled where stud goes in .try new cover
@user-tx8hd2jw7u 2 ай бұрын
You just don’t know what was done to it before it arrived on your bench. There’s some real thick neck buggers out there who can muller anything!
@greebo7857 2 ай бұрын
Think the problem is your clock's stopped, Mike.
@axelboldt5101 2 ай бұрын
may be the Deliverquantity is different ?
@bigears4014 Ай бұрын
What do you expect, they have never been a quality item
@jameskerr5756 2 ай бұрын
Could drive you nuts chasing something like that. I'd be reluctant to remove that pump again but I get that it wasn't the one the box came with. Hope something was found with the plate to explain the issue.
@BritannicaRestorations 2 ай бұрын
See next video when I get change to make it!
@fire44x 2 ай бұрын
The plate hole is not circular there's a low in the countersunk hole
@axelboldt5101 2 ай бұрын
may be the Oring is to hard?
@BritannicaRestorations 2 ай бұрын
Could be
@axelboldt5101 2 ай бұрын
@@BritannicaRestorations i had some on the Dieselheater when it runs and was warm no leckage when it stops running starts lecking there was a problem with the thickness and to less shore
@nicholasviney5975 2 ай бұрын
Those jobs can make you lose it
@zibobpompon5768 2 ай бұрын
Défaut de planéité !!
@axelboldt5101 2 ай бұрын
to much shore?!?
@mattluszczak8095 2 ай бұрын
First
Britannica Restorations Ltd
Рет қаралды 4,3 М.
Britannica Restorations Ltd
Рет қаралды 2,7 М.