BSA A65 'Oil tap engine' strip & rebuild 7 Checking the oil pump.

Рет қаралды 1,589

22 күн бұрын

It would be foolish to do all of the work carried out so far and with having replaced the conrods and big ends, not to check the oil pump over.
Here, I take a look at the components that make up the oil pump, having stripped it just prior to filming this clip.

Пікірлер: 27

@norsehall309 19 күн бұрын

😅 g'day Paul, the only time my classic bikes wet sump is from under use, so the night before the bike I'm going to use has the oil drained, the worst contender is my Royal Enfield Bullet 500 but it's the easiest to fix, undo that front sump plug and drain but don't forget to put the plug back and check the oil level, cheers mate Neil 🤠.

@neilmcintosh1200 20 күн бұрын

The risk of wet sumping is always compounded in bikes which are not in daily use, which these days is almost all of them!. I'm in full agreement, change the pump.

@gordonsuddery4635 19 күн бұрын

Definitely do away with the tape and I'd fit a new oil pump probably from SRM. Love the work you do my best wishes from the Philippines 🌹👍😀😉😁🤔😁🏍️🛺🐑🇵🇭🏴󠁧󠁢󠁷󠁬󠁳󠁿

@paulhenshaw4514 19 күн бұрын

Thanks 👍

@andrewgent5887 20 күн бұрын

I fitted an SRM pump which solved the wet-sumping problem on an A7SS I was the custodian of a few years ago.

@hermangibbs8163 20 күн бұрын

Thanks Paul.

@markberry2969 20 күн бұрын

Too right Paul.

@bsa_brummie7775 20 күн бұрын

All that work and expense I would 100% replace the oil pump.

@grateberk6435 20 күн бұрын

Wonder what the life expectancy was for a reasonably well serviced engine from the factory

@paulhenshaw4514 20 күн бұрын

Probably quite respectable, I would have thought.

@track1219 20 күн бұрын

Great question. I would guess a British bike from the 60s and 70s should go 20,000-30,000 miles before valve work or more is required. Clutch maintenance and an occasional gasket well before that. My 2 cents.

@progvinyl9021 19 күн бұрын

They didnt last long troublefree here i Norway lots of problems 60 and 70's bikes

@billdancliff6434 20 күн бұрын

Paul is there any way to install an oil pressure gauge to a 1966 A65?

@paulhenshaw4514 20 күн бұрын

Don't go there, honestly!

@Kyle-ir3bz 20 күн бұрын

Hey Paul, do you still use the bushing from a Ford tractor as a replacement for the BSA timing side bush?

@paulhenshaw4514 19 күн бұрын

So far only one used and I presume all is well. It is a viable option which can cater for small undersizes and probably made of better stuff than a lot of other options doing the rounds at present.

@Kyle-ir3bz 19 күн бұрын

Good to know. Thank you.

@gpo746 20 күн бұрын

Special conrods? Are they the steel Hepolite ones Paul?

@paulhenshaw4514 20 күн бұрын

No, these are alloy by 'R&R', from Burton Bike Bits. American made, apparently.

@user-hd6fm3eg5s 20 күн бұрын

Love your British bike videos, never known you call any British bike shite.

@paulhenshaw4514 20 күн бұрын

Thanks - that is because none of them are!

@user-hd6fm3eg5s 19 күн бұрын

Brilliant response

@paulhenshaw4514 18 күн бұрын

@Turnipstalk BSA Beagle - I have no direct experience of them, but as with many others - including certain Hondas - were they as bad as the story tellers made out?