Build A 2 Cylinder In-line Two-stroke Engine

Рет қаралды 2,484,437

4 жыл бұрын

How to Build A 2 Cylinder Inline Two-stroke Engine using 2-stroke Engine at home
Thanks for watching, Have a great day !

Пікірлер: 1 300

@BlusEXE 3 жыл бұрын

The fact that this lad just has a pile of 2 strokes lying around makes me sooo jealous. Keep up the great work!

@catman4644 3 жыл бұрын

Lad? This appears to be a LASS, which makes it all the more remarkable!

@frankw8315 3 жыл бұрын

ikr

@frankw8315 3 жыл бұрын

@@catman4644 it’s a lad

@tandmbros5877 3 жыл бұрын

My freind here in america has a pile of two strokes... you can find free weed whackers a dime a dozen out here

@wompstopm123 2 жыл бұрын

@@catman4644 hes a lad, the long nail on 1 finger is for doing cocaine

@buzzsawncgo2751 4 жыл бұрын

I had a motorcycle that was made almost exactly like that back in the mid 1970's. It was a 500cc Yankee. The engine was made with two 250 cc Ossa barrels mated on a common crank shaft. When the folks at Yankee were initially considering the splice, they tried the engine with the pistons firing on opposite strokes so that power was continuous but found that the bike (which was intended for enduros) had a more useful power band with them mated on the same stroke. The power was like that of a 500cc single. They called it a twingle, or at least the riders did. It was massive in the woods. If you had the alternate stroke config. it just spun the tire and the power didn't get to the ground. Wish that I never had let it go.

@davidelliott5843 4 жыл бұрын

Before WW2 there was a genuine Twingle aka split single. Two con rods with offset crank pins two cylinders pumping one cylinder head. One on inlet side and one on exhaust. It gave a longer dwell time at TDC but poor gas flow meant no overall advantage. . kzfaq.info/get/bejne/adeHqc9qprzKkXU.html

@davidwillard7334 3 жыл бұрын

CHAINSAW !! WOULD BE ! GOOD !! FROM IT !!

@jacketspritecranberry4876 3 жыл бұрын

You need to time the engines correctly one engine with the piston at the top, and one at the bottom, and make sure the idles are at the exact same rpm. Notice how there’s only smoke coming out of one of the engines. There’s air coming out of both because of compression, not because their both running

@acoder912 3 жыл бұрын

my thoughts exactly, the idea is good but i not sure its actually running on two , is it 360 or 180 degree timing? interesting idea for a four cylinder.

@jacketspritecranberry4876 3 жыл бұрын

@@acoder912 it would probably be 180 degree timing

@jacketspritecranberry4876 3 жыл бұрын

@Jade Spale 180 would be ideal because when one engine is at the exhaust stroke, the other would be in the combustion stroke. 180 degree timing would have the best affect on power for a two stroke, I feel 360 degree timing would be best for a four stroke

@therallyguy1 3 жыл бұрын

@Jade Spale reference YAMAHA BANSHEE 350 Twin 2 stroke.

@charliebrown238 2 жыл бұрын

Actually, you dont "need" one at the top, and one at the bottom, since they both have 1 ignition coil per cylinder, they are both individually timed. (Unless he is using 1 coil to fire both cylinders, then timing could be off) Look at all v twin motors, they are not one up and one down. Id dare say since we seen it had spark on both cylinders, that it must be a fuel delivery issue on the "non smokey" side.

@phoenixme74 3 жыл бұрын

Now you have two engines that will be a pain in the ass to start each spring 😁👌

@joerolfe7967 3 жыл бұрын

Even though this is a twin engine setup and not twin cylinder, its still very cool and man it sounds way cooler then i would have expected. Nicely done.

@kimkeam2094 4 жыл бұрын

Interesting build, and very informative. Two things that stand out. A carburettor balancer is required otherwise idle will never be stable or you can accidentally run one lean at operating revs, ruining that cylinder. Secondly, cooling is now missing on the number two engine as the fan shroud was removed and no metalwork to guide the airflow from the front engine, or the machined impeller to even slightly reduce cylinder head temperatures. I guess it is a work in progress. Perhaps fitting a multi blade shrouded propeller on the drive shaft, with adequate baffling ,would be able to draw the air past the cylinder and vent it away from the engine.

@nathaniellangston5130 4 жыл бұрын

It's pretty cool how you connected the two engines! I wouldn't have thought to do it that way!

@Backwoods-Bob 4 жыл бұрын

Reminds me of Garage 54 putting two 4 cylinder engines together, and running them in a Lada(?).

@aliciaantoniadis9100 4 жыл бұрын

Yes!! I saw that one and I liked it very much! Thank you for this comment.

@szypki_zygi 4 жыл бұрын

They did 4 of them later down the line XD

@BotijoRural 4 жыл бұрын

Yes, in a lada. Garage54 rules

@beeftec5862 4 жыл бұрын

Garage54 werent stupid enough to call it a V8 though

@borivojetravica569 3 жыл бұрын

Giv us the link!

@lukimyu1 4 жыл бұрын

I have been looking for something like this for ages!!!

@joeMW284 3 жыл бұрын

Pretty cool. I think the cylinder without the pull start would be in danger of overheating if you did any real work with it though. And like others said, putting the two cylinders 180 degrees out would prevent the assembly from rattling apart.

@JohnJaggerJack 4 жыл бұрын

Now do that until you have an inline 8 cylinder two-stroke engine, and put it in the kart.

@yoellobi 4 жыл бұрын

jajajaa

@Bizones16 4 жыл бұрын

Why Stop there ? ! Get 6 or 8 V-Twin 4 Stroke engines and mate them ALL together for a V12 or V16. THEN we can have some FUN !

@Bizones16 4 жыл бұрын

I forgot in my previous reply, run them in a FLAT PLAIN CRANK configuration.

@bubgyu3961 4 жыл бұрын

What about V or F

@marcw2604 4 жыл бұрын

@@Bizones16 or opposed twin air cooled in to a boxer 4 or 6 ect

@james8660 4 жыл бұрын

That coupling you made is pretty smart, avoids the alignment issue if you wanted to hard mount it together I guess!

@pedrohenriquecordeiro3954 2 жыл бұрын

😰😵😤😣🌞☁

@nicholasgaudet6309 4 жыл бұрын

Hands down the coolest thing i've ever seen anyone do with a couple 2 stroke engines.

@oscaruiz8055 4 жыл бұрын

those two motors have a beautiful sound when working together congratulations great idea (I'm already anxious to see what you plan to use it on)

@John_Makes 4 жыл бұрын

Nice work I'm doing the same thing with 2 pocketbike engines but i used cam sprockets and a timingbelt to join the two engines! Runs great but i will change it to a 1 carb instead of 2

@SteelCityRC 4 жыл бұрын

Very inventive work. Would be nice to have that lathe. Twin 2 strokes sound so mean. Two Walbro carbs and steel tuned pipes is the ticket. Nice work on this one!!

@jackshadowblades2957 3 жыл бұрын

This is cool thanks for posting it. I'm gonna try building one and installing it in an old pedal cart tractor

@parkersposts 3 жыл бұрын

Please post a video of it if it works it might do wheelies!

@White_Night_Demon 2 жыл бұрын

so how did it go?

@firerejack1121 3 жыл бұрын

Make a v8 engine with just these little strimmer engines that would be amazing 😂

@youtube.youtube.01 4 жыл бұрын

Very ingenious! Creative crankshaft coupling is an interesting challenge to watch other people solve!

@philippwetter 4 жыл бұрын

Next you should do a inline 3 with a 120 Deg crank offset, would sound sick!

@Sauron_Green 3 жыл бұрын

I've seen these motors used in 2-stroke friction drive motorizing kits. Note that I mean the single cylinder not the custom twin cylinder you've made. Also, it would be amazing seeing put into action as a custom motorizing kit for pretty much any driveable platform.

@MrThunderCunt Жыл бұрын

Im currently build a performance engine woth one of these. I ported it and polished the exhaust, bigger carburetor, and a home made bracket to move the coil and change ignition timing. Also have made my own exhaust for the project im using it for, which is a full suspension mountain bike. Im modifying the suspension of the mointaim bike aswell to get more travel. Also adding some fender and stuff so it will basically be a dirtbike. Im also figuring out a way to use the stock shifter mechanism to shift it. Maybe maje it a 3 speed, but idk yet.

@john7630 5 ай бұрын

Where is time belt?

@quentin8094 4 жыл бұрын

“For the toughest of weeds”

@davidwillard7334 3 жыл бұрын

WHAT !!?? FOREST !! TREES !!?? MAYBE!! ROCKS !! TOO !!!

@maybejapheth 3 жыл бұрын

Underrated 😂

@OpitiumThirtyTwoIncOTTI 2 жыл бұрын

seeing this engine mounted and running would be awesome 👍🏻

@lowellmunz 4 жыл бұрын

Great skill! All my respect. 🙌

@jeeper426 4 жыл бұрын

i dont know why i'm imagining this on a weedeater now, cool build

@neko7684 4 жыл бұрын

literally same

@justin456 4 жыл бұрын

Moar power babeh

@garymucher9590 4 жыл бұрын

Rear or second engine looks like it is running richer then the first. Since both are supplied via one tank, you may want to richen up the first engine some to keep from heating up... But very interesting build all the same.

@johnblack7943 4 жыл бұрын

I was just saying he should just make a manifold and use one carburettor for both

@user-kn5ol8ck8s 4 жыл бұрын

dual carbs are actually better but you have to have them adjusted exactly the same. Take them both apart and rebuild them both the same with the same adjustments.

@JoshPhoenix11 2 жыл бұрын

I've always wanted to see a 2 stroke radial engine made with these

@darinmckillop6196 4 жыл бұрын

Very creative I been a small engine mechanic for 40 years and this is good.prob just double fire cute.it would be neat to dino 1 and the other to see if there's much of a difference Great prototype for something better good luck

@BlusEXE 3 жыл бұрын

I can only WISH I just had a pile of engines lying around.

@jackstrempel5135 3 жыл бұрын

I got a pile of blown up race car engines in my shop

@pauls5745 3 жыл бұрын

I think I'd try to make a custom dual intake for a single, bigger carb and try to make 2 expansion exhausts. then drop it in a motorized bicycle I'd love to see more people do things with this!!

@charliebrown238 2 жыл бұрын

That would most definitely make starting, and tuning a hell of alot more easy. Although the twins would make higher hp overall, i think the tuning and syncing would out way the power increase for drivability and ease of everything

@aliciaantoniadis9100 4 жыл бұрын

As always, very well done. Be well, and thank you.

@fermzy 4 жыл бұрын

Could you install a fan??

@thomasteichert8737 4 жыл бұрын

I need two of them for my bike! :DDD Great job!

@dennism644 4 жыл бұрын

Should try and hook a chain bar to that set up for a twin cylinder chain saw

@mycoboto 4 жыл бұрын

Twin cylinder chain saw eh? Now i can manscape with confidence!

@dydy71580 4 жыл бұрын

Twin cylinder chainsaw exist : Echo cst610evl and solo

@davidwillard7334 3 жыл бұрын

ECHO !! Had a Twin Cylinder !! Saw !! Back in the Eighties !! In there Catalogue!!

@braydenbratcher3730 4 жыл бұрын

These are the kind of videos I’ll I like people working on engines and putting and making odd things with the coolest machinery

@HolzDennis 4 жыл бұрын

I need one of this beast for my Chainsaw 👍🏻

@Chuffin_ell 4 жыл бұрын

A collaboration between this channel and “the practical channel” would also be very interesting...

@beeftec5862 4 жыл бұрын

Even more so with "the accurate thumbnail description channel"

@dimavieru8999 4 жыл бұрын

great job man, can you built an inline 4 6 8 10? i guess be amazing to put it in to a bike like kawasaki 6 cilinder

@Undertaker1134Tx Жыл бұрын

Love the build. Did the same to rc nitro motors though I've been wanting to build one of these to make a custom moped a duel 25cc in a alt fireing flat config. The carbs are not synced, mark the output crank to read rpm, unplug 1 sparkplug@ a time to adjust each running side to match idle rpm.

@Twin_Flyer 4 жыл бұрын

Interesting build! Need to find it a home now. Where did you get the fuel fitting for the tank you modified? i need one for a project!

@jasonb4350 3 жыл бұрын

Right engine is not running but still shows the paper moving because of compression escaping through the exhaust and I say this because there was zero smoke coming from the right engine.

@JonBecker81 3 жыл бұрын

It was running. He adjusted the idle on it and it sped up and slowed down.

@Alex-qb1kp 3 жыл бұрын

12:58 you can see smoke

@repsaii3855 3 жыл бұрын

Hell yes it was. Look at 13:05 there you can see the smoke

@bagusreformasi6911 3 жыл бұрын

@@Alex-qb1kp ................... 53

@timwever6793 3 жыл бұрын

both running but fist one hase more takeouts than it actuell runs. wrong timing

@manuelbertram8785 4 жыл бұрын

Do they ignition at the same time or did you mount them 180° apart?

@friscoHub415 4 жыл бұрын

Love the pinky nail I been rockin one forever

@roiedavid3830 4 жыл бұрын

I wish i could have that for my proj to my scooter, watching here from the ph

@huntergrissett6697 4 жыл бұрын

This needs to go on a scooter or a motorcycle 😂 I gotta see it in action

@billthetaxman89 4 жыл бұрын

"let's learn something" channel should collab with you...

@briankuhn7396 2 жыл бұрын

Such a fun project!! Did the flywheel magnets/crank get offset, or are both cylinders firing at the same time?

@paco_rider 3 жыл бұрын

Two-to-one (90's kids will remember)

@mateuszdobija2961 4 жыл бұрын

the first engine must be in TDC second engine must be in Bottom Dead Center, engines must be synchronized, when first make the power stroke the second must make the compression stroke.

@kcpilot21 4 жыл бұрын

I was thinking the same thing. Engine and spark timing.

@santiagoperez2094 4 жыл бұрын

That would be the best choice to smooth torque, but isnt necessary at all.

@yudiwahyudin6644 4 жыл бұрын

Maybe 270° sound better. 😁

@Gamer-nc8qp 4 жыл бұрын

this yes

@dieselgeezer18 4 жыл бұрын

the timing is not great. But it doesn't need perfect timing to work. There are many types of engines with some weird timing

@quintenvekemans9493 4 жыл бұрын

@<a href="#" class="seekto" data-time="248">4:08</a>minutes those are some badass safety shoes 😂

@aidanlast8623 4 жыл бұрын

Quinten Vekemans Japanese work boots

@davidwillard7334 3 жыл бұрын

I !! HEAR !! THAT !! THEY !! ARE !! QUITE !! GOOD !! AND !! THERAPEUTIC !! FOR !! ARC !! WELDING !! TOO !!!

@FIXDIY 4 жыл бұрын

It is a mental activity characterized by departing from customary thinking and producing creative ideas

@repalmore 3 жыл бұрын

This would be a fun project for an RC airplane. Maybe a cowling to help with cooling or something like that.

@chrislaz2473 4 жыл бұрын

What's the parallel twin gonna be used for? Bad ass weed whacker?

@FirdausIdros 4 жыл бұрын

yes and drone engine too!

@Rudofaux 4 жыл бұрын

@@FirdausIdros Engine is too heavy for drone usage. Sure the power to weight ratio is there, however you're forgetting the propellers would need to be substantial to lift just the weight alone not including the drone's own frame work.

@wildcoyote34 4 жыл бұрын

@Rudofaux the drone engine idea is a good one but i would use a 1 cylinder engine and a generator to increase the flying time of the drone ,,I built a prototype of my own with a 38CC chainsaw engine about 2.5HP,it generates 12.5 amps at 36V ,,the entire assembly weighing just over 8 pounds including the rectifier and regulator controller ,,it was installed in a 4ft Octo-copter drone and was able to fly for 83 minutes nonstop powered by the generator alone before a rectifier burned out I have also experimented with building an engine powered drone ,this was a mixed success because while this machine which weighed near 20 pounds had excellent lifting power it didn't have the control of an electric drone .totally mechanical driven the control was accomplished by literally swiveling the arms with the propellers ,,,and finding gearboxes capable of the RPM and loads necessary for this was quite easy ,,,literally ANY strait shafted weed trimmer has a gearbox capable of handling continuous 9000 rpm operation

@banana_beard8871 4 жыл бұрын

He could use it for a gas powered Bicycle. Kinda like those kits but better.

@joeMW284 4 жыл бұрын

yeah, you could do a bike.. rack mount on the back would probably be the best way. This motor is pretty long.

@saharut4513 4 жыл бұрын

I want to see 4 stroke engine like this ++

@stevemartin7721 4 жыл бұрын

That'd be a potent little engine for a kids cart...thanks for posting.

@victoryfirst2878 4 жыл бұрын

I really like the collection of engines you have Sir. Nice work too. VF

@douro20 4 жыл бұрын

Anyone know how good those engines are? They remind me a bit of old Echos.

@enriquecuellomartinez9622 4 жыл бұрын

Muy bien el trabajo.. Pero a mi parecer solo hay uno de los motores encendido... Por la razón k solo uno está husmeando 😕

@dustinbowser2762 4 жыл бұрын

Enrique Cuello M

@srcarlosvaquera 3 жыл бұрын

Try to do an engine "V" from 2 motorcycle engines

@chadscott2499 3 жыл бұрын

I meant to send that to some Yahoo

@michaelrobertson8795 4 жыл бұрын

That'd be pretty cool to put that in a remote control deep V boat.👍

@hanako-kun9407 3 жыл бұрын

ยอดเยี่ยมมากครับ อยากให้ลองทำกับเครื่องยนต์เบนซินเอนกประสงค์ 7.5hp.ด้วยครับ จะได้เอาเป็นแบบอย่าง ขอบคุณครับ

@briancamp8261 4 жыл бұрын

All I can say is that my friend that is one hell of a weed eater

@maxbetbrawn6663 4 жыл бұрын

Интересно для чего он поженил двадвигла? Рядом на столе редуктор лежал! Ждём-с короче!

@bagaboo3736 4 жыл бұрын

CoглaceH

@AlexMoonXXI 4 жыл бұрын

Судя по другим видосам автора - он любитель мопедов, картинга, багги и прочих мототележек...

@Krasnov_Misha 4 жыл бұрын

@@AlexMoonXXI какой нибудь веломопед может будет

@AlexMoonXXI 4 жыл бұрын

@@Krasnov_Misha А я сначала думал - какой-нить индонезиец мастерит себе лодочный мотор. У них дофига типа байдарок с моторами от бензопил или газонокосилок. Такая длинная труба, на одном конце винт, а на другом - мотор.

@Krasnov_Misha 4 жыл бұрын

@@AlexMoonXXI будем следить

@davewolf8869 4 жыл бұрын

Interesting lovejoy coupling you made there XD

@BorosTheGamer5021 4 жыл бұрын

i wish i had something like that for a motorized project

@Prosto16Simvolov 4 жыл бұрын

А бумажка возле выхлопа принудительно вращающегося двигателя это показатель его работы? На видео видна работа одного двигателя. Синхронизация двигателей одной только отвёрткой не выполняется.

@Zdobik 4 жыл бұрын

Я тоже про это видно по выхлопным газом что первый в холостую а второй в напряг.

@user-ep6cq4tv2w 4 жыл бұрын

Привет, сделай мот с этим двигателем

@doom2507 3 жыл бұрын

Wow you've got alot of engines there !

@slicaltimistic1 4 жыл бұрын

😁😁😁Alright. Let's put that twin 2 stroke on a bicycle, or scooter and let's see some numbers next. And do a 12 cylinder 2 stroke. This I got to see.👏🏼👏🏼👏🏼

@billbaden742 4 жыл бұрын

How are you going to get airflow across the second cylinder

@lelandharper2099 4 жыл бұрын

BrickyBoi no, he means cooling. Air cooled engines don’t cool well with no air being blown across them lol

@tomasrous7324 4 жыл бұрын

It looks like only one is firing, bcs there is no smoke coming from one

@ondrejfusek9004 4 жыл бұрын

Čech? 😁

@mr.engineear0987 4 жыл бұрын

Yeah so, it is still firing with very low amount of smoke coming out on the second cylinder

@mr.engineear0987 4 жыл бұрын

Anyway you can see smoke coming out both at 12:58

@crudboy12 4 жыл бұрын

It's obvious that both are firing. You can see smoke coming out of both at all times. It wouldn't run properly if only 1 was firing anyway.

@hkmusicfactory7480 4 жыл бұрын

kaise ho bhaiyo

@gtgodbear6320 3 жыл бұрын

My uncle built my cousin a go-kart with 2 47cc two stroke engines. Both cylinders would fire at the same time. It felt way faster than it should've been.

@RBAERO 4 жыл бұрын

Very nice!!! Question both piston explode at same time or is one at the time? How do you set this timing?

@skynjaydensdaddy 4 жыл бұрын

Last time I checked inline isn't considered a "V"

@deborahchesser7375 4 жыл бұрын

Al H they got us watching though didn’t they

@Studdfromhell 3 жыл бұрын

Still cool tho

@oppaiwarrior1015 4 жыл бұрын

Thats twin 2 stroke engine , should be powerfull if you using those engine to make RC car (remote control ) car 💪💪💪

@vampiregirl32 4 жыл бұрын

😍💯💯💯💯💯💯 for off-road RC that will be epic 💯💯😍💯😍

@rebelforce4965 4 жыл бұрын

Monster truck or Buggy. 🤩🤩 Yeah that would be awesome

@roscoe454 4 жыл бұрын

awsome job! hey i would put a air guide on the little beast ! :)

@AldreenEllohin 4 жыл бұрын

I'm looking forward to seeing where this engine is going to go !!! o/

@davethewaffler2336 4 жыл бұрын

You should try and make a an inline 4 cylinder

@jirirybacek5488 4 жыл бұрын

What about 6 😅

@themagicphoneboothq4529 4 жыл бұрын

V8 or nothin

@Rudofaux 4 жыл бұрын

@@themagicphoneboothq4529 (laughing in rotary)

@appelmelk5664 4 жыл бұрын

Just keep adding till you have a straight 16 or something

@donaldshimkus539 3 жыл бұрын

Hasn't anyone seen the FrankenBriggs ?

@arisz2191 4 жыл бұрын

It's dual in-line cylinder, NOT V engine

@ChannelCreativeVN 4 жыл бұрын

thank bro

@niel67354 4 жыл бұрын

If the crank is joint at the right offset it will sound like a V.

@arisz2191 4 жыл бұрын

@@niel67354 make it 270 degrees

@guanovolante7833 4 жыл бұрын

@@niel67354 but it is not a "V" shape, so it is not a V2

@elianedapenha1317 4 жыл бұрын

@@ChannelCreativeVN teaches you how to make an ulv cold fogger

@holgers5216 4 жыл бұрын

LOVE the safety boots!! LOL!...needs twin SU carbs!!!!

@NG-zg8vf 3 жыл бұрын

You should set one engine to Tdc and the other to bdc, also make a joint intake manifold, easier to set up with one carb.

@user-ly6fl4ve7w 4 жыл бұрын

It's interessant. Well done!

@papapaniop 4 жыл бұрын

No its not interesant

@rayscyclesrepairs3516 4 жыл бұрын

“Sounds like it’s running on One cylinder” 😂😂

@Optimuseq 4 жыл бұрын

And even looks like 🧐

@nainon3842 4 жыл бұрын

Yea its only running on one cylinder😂😂

@thomasrankl8011 4 жыл бұрын

i think so too - the ignition is the problem

@Optimuseq 4 жыл бұрын

@@thomasrankl8011 whole project is done with many issues. Spark timing, cooling of the second cylinder....

@marlobreding7402 4 жыл бұрын

In the 70s we had 2 strokes called Twingles, both pistons were on the same phase of the stroke. The fired together

@tigergrover7 4 жыл бұрын

I am your big fan

@kingyamaha9637 4 жыл бұрын

Go inline 3 or 4 that would be very impressive and first ever on KZfaq

@hitman6647 4 жыл бұрын

Love From South IND♥️

@Rudofaux 4 жыл бұрын

Won't take long for that rear unit to overheat. The flywheel's fins were cut down reducing airflow & no shroud to redirect said airflow. No airflow, no cooling. Nice little project thou.

@Hellsong89 4 жыл бұрын

Custom shroud to go over all of them and make first one have actual fan blowing trough the setup.

@ostolski 4 жыл бұрын

that's the first thing I thought too and it's not practical unless you rotate the cylinders 90° and blow the heat to the side and install a shroud on the second motor at least the block the heat from blowing on it from the first one

@jaymesc.moreland9265 4 жыл бұрын

@@ostolski A decent fan and baffle setup could still blow enough air to cool the rear cylinder without staggering them. Small aircraft such as the Cessna 172 do it all the time with 2 or 3 cylinders in a row.

@javierbarradasindo4253 4 жыл бұрын

La verdad amigo desde que sigo tu canal me ayudado para algunas ideas... en verdad muchas gracias por compartir sigue así... ya he hecho algunos de tus proyectos y en verdad no sabes cómo me han ayudado.... saludos desde cancun Quintana roo México.

@cadejohnson5473 4 жыл бұрын

This is pretty slick, sounds pretty good too.

@user-mw4gx5kf7j 4 жыл бұрын

А чё с первого горшка не дымит, а дует? Может он просто нагрузка?

@user-kj7xt8jm1o 4 жыл бұрын

А вто это вот защем? Я просто по ихнему не шарю . Что с ней дальше то делать?

@MOTOPEMOHT68 4 жыл бұрын

Смесь беднит на первом.

@JohnnyEST1 3 жыл бұрын

What about cooling of the second cylinder? There is no fins and a cowling to aid cooling

@crazycreation6992 4 жыл бұрын

Can you make a rc boat with this engine..

@zacharykosinski2883 4 жыл бұрын

Engine is too big

@eloxdgg 4 жыл бұрын

Yea

@FM60260 4 жыл бұрын

@@zacharykosinski2883 Why not put it in a bigger boat?

@zacharykosinski2883 4 жыл бұрын

Volvo B10M true but that would have to be a really big boat. So maybe that is a good idea it right

@peterbrown172 4 жыл бұрын

Would it still rUn ok if you bolted the second engine on with the crank 180 degrees offset from the other engine? I wonder how that would sound? Would it be more powerful?

@CBCycles 3 жыл бұрын

Great job, thanks! Do you know the firing spacing, in other words do they fire together or 180 degrees apart, 270 etc?

@JoshPhoenix11 2 жыл бұрын

It sounds like he aligned both flywheels together at top dead center it doesn't sound like a 2 cylinder. You can here it better at 9:05

@tunuk_kg6973 4 жыл бұрын

Мне кажется один движок не работает? Тот который не дымится при нажатии на газ 🤔🤔🤔

@arturatsaev3412 4 жыл бұрын

100 % не работает, 2 двигатель вращает первый и с выхлопа выходит давление!

@tunuk_kg6973 4 жыл бұрын

@@arturatsaev3412 Да темболе туда добавляют масло, дожноже дымет при газовани, по любому а второй выполняет роль компрессора

@user-ju8qu9gc6v 4 жыл бұрын

У меня триммер не дымит. Развожу "лукойл мото2" и "штиль 2т", 20мл/литр. Триммер "champion" T27. Не факт что двигатель будет дымить. Это вам не планета и не восход. Ещё не меньше от износа цпг и настроек карбюратора зависит.

@filyamatross4100 4 жыл бұрын

@@user-ju8qu9gc6v зависит от положения дозатора в игле, а не от фирмы двигателя. На видео второй беднит, первый богатит

@c9rpses 4 жыл бұрын

you're bored in quarantine right? XD

@hkmusicfactory7480 4 жыл бұрын

hii

@robertomeneguini9486 4 жыл бұрын

Muito bom adorei ...faz um com motor 4 tempos estacionario.

@lordj.8962 4 жыл бұрын

I have a twin two stroke too that’s rad!

@jaymarch5 4 жыл бұрын

Next : V6 With 2 Stroke Engine

@davidwillard7334 3 жыл бұрын

NO !! VEE !! TWELVE !! PLUS !!!

@Kydenius 4 жыл бұрын

Could you make a 4-stroke inline 2 motor like this and show us how to put it in a bicycle? Thank you!

@bradenwestfall5052 4 жыл бұрын

It already technically is an inline 2

@tc1254 4 жыл бұрын

Look up Zeda motor sports they made a twin engine 2 stroke on a bike

@DooberD33 4 жыл бұрын

that shits impressive

@user-rk2vv1yi6b 4 жыл бұрын

@@bradenwestfall5052 ไฟ่าาา่รรรณานี่นนยยาืาืาืิ่้่รานชบ่้่วทาาาสสสสสสนา่้่ร่้ร่ารรรรรรรรรรรรรรร่ีรรรรนนาสาาาสววใมวสทสมมซแ้แสทท ทระู

@Sebi076 3 жыл бұрын

I'd love to have all the tools and scrap peices and whatever you guyd have so i can build my own engines.

@alexsz.6530 2 жыл бұрын

Lets make more two , im so inspired to watch inline four cylinders with this 2stroke 💪🤣

@premjitsingh36 4 жыл бұрын

Only one cylinder is firing not the second he shows with plastic paper that both are firing but only one as smoke is coming from only single as it's 2 stroke engine both should show smoke

@kgb5223 4 жыл бұрын

No, both cylinders are firing, you can clearly hear it. It must be a carburetor tune issue, the one cylinder that's not smoking might be running a bit lean... Or the one that's smoking might be running a bit rich. Sometimes two stroke engines don't emit that much smoke.

@ukutominga4504 4 жыл бұрын

ideally, none of them should have visible smoke coming out

@Sebi076 Жыл бұрын

Bad english you have yes

@dustinmiller7278 Жыл бұрын

@@ukutominga4504 if you don't have visible smoke coming out of a 2-stroke you're running it too lean and you'll blow the motor

@badblenderanimations1449 8 ай бұрын

@@kgb5223he's right, I have a two-stroke motohoe and it only smokes when the engine is really cold or when I can't start it first try. It can also depend in the oil you are using...