This guy is my hero. Who else can pull off riding a diy e-board in a leather jacket and flip flops? He's good.

I followed your video, and so far so good. Thanks for putting this on KZfaq, it was very helpful. It has a rough start, but once it gets going it is very smooth. Here are some tips for the ESC that is on the parts list: How to Match the Remote Control with the Controller Board: 1. Connect the control board to power source. 2. Turn the control board power on, wait for 2 seconds. Then press and hold the switch for about 6 seconds till the power indication light flickers. 3. Turn on the remote control and use a small screwdriver to press the code synchronize switch in the lower left corner of the remote control. 4. Turn off the remote for 2 seconds and then turn it on. Wait for the remote control signal light and the switch signal light to flash at the same time, which means that the match is finished. Specifications: - Name: Four-Wheel Skateboard Longboard Controller Set - Voltage: 36V, 10S - Current: 12A - Speed: 4200 RPM - Max. Power: 430W (36V) - Drive Mode: Dual System Drive - Max. Speed: 35KM/H - Protections: Over-voltage, Under-voltage, Over-temperature, Stall, CW/CCW, Adjustable Speed - Sensing Way: Hall - Power Connector: XT60 Male Plug - Motor Plug: 4mm Banana Plug - Max. Load Capacity: 120kg- Remote Distance: up to 20 meters The remote has 4 speed settings, you change the speed setting by pressing the power button (after you have already turned the Remote control on). Press it once to change the setting, and then once again to increase the speed range. You can also increase it by pushing the throttle all the way, releasing it and quickly pushing it all the way again. Thanks again, great video

Unique !! I guess hub motors need more power for better runtime.

Thanks for sharing. This man has a lot of skills. I wish I knew how to weld. without that he would not have been able to complete this project. Cool project.

Great Work :)) and the MAKITA LH1201FL Combination Mitre/Table saw- What a fab tool for diy'ers with no work space :))

Who loves Creative channel? 😍 😍

CONGRATULATIONS DUDE! i love your eletric longboard!

You have complete tools and the materials that supporting your talents sir. Wood, steel, electronics. I'm imagining about owning those power tools and all stuff in my garage in the future. All is available in my rack. I guess you have a little factory in your house.

Молодец, классная работа. Respect.

Fantastic work, dude! Really nice! 😃

Uma ideia muito boa .Parabéns

Trabalho de um gênio,parabéns 👏👏👏👏👍🤜🤛🤝

Muito Bom... Parabéns!

First, great video! Thanks a lot! Secondly, does anyone know the exact instructions? What are the sizes, etc?

This what I call DIY. Great job mate

Nice idea, please, show offroad usage. That is 4wd e-board should be good for

Chip and Dale having a conversation in the background 😄

I love the sound of saws in the morning XD

Nice to have a home depot as your house

If this driver is dual motors only, how is it able to run all four?

What an awesome skateboard I liked 👍

You are really a creative guy. I like your all videos. A real creative channel. Keep going...

Thankyou for trimming your nails 💅

Oo bro your things has stocked Then amazing

Eu estava com saudades dos seus videos amigão !

you can make it at home if you already have a workshop and electrician store at home

Thanks for the tutorial, i have a question, Where do I get the hoverboards? and how to much.

I love your work you have a fan

You its great engineering,its king of constructor😁😉😉😉😉😉😉

Ficou top , mas acabou com o piso onde as fagulhas de fogo pega mancha o piso todo 😂😂😂😂😂

How did you connect wheel cables? There 3 thick and 5 thin. Where did you put thin?

SUPER!!!!NICE!!!

wow, every single part are handmade... except for the hub motors... !!!!!!!!!

who like before watching

cool project.

I like your boach cutter

Haha that's so awesome!!

Amazing electric skateboard man!! It's really cool

Very very hard work😢 but you make nice 😊

I'm intrigued to what speed controller is used,,as here in uk we would use one controller on each wheel 🤔

did you connect the Hall sensor cables in parallel as well, like u did for the phase cables?

Nice making

your intelligence is on the next level 😀😀😀😎😀🙅🙌🙏🙏🙏

Muy bueno el video amigo, pero le pregunto la tarjeta eléctrica que uso, es de la patineta original. Y cual de las dos cogió. Gracias.

*Creative channel do a video on your lab tour..full lab video..i have been waiting for that for long*

this is play a lot for my cosplay! thank you do much♡ and thank you for great video but I have a question, can they turn to the left or right?

Dream garage!

could build iron man with this guy's tools

Living well in a building materials store

Please KST and Creative Channel do a next video for your full lab im so excited to see your lab

Bravo شكرا

Where do you get all the electrical and engineering parts from do you collect them from discarded items

Increíble, muy buen viideeo, eres un chingon

Awesome!!

Show de bola 👍👏👏👏

Well Done.

Please make an agriculture hexacopter spraying drone

Your videos are awesome

if you add a seat and handles, you will get a great transport for the elderly

Excellent project

who loves creative canel?😍😍

Vidéo is very good

Creativ and Genius😀

hi KST ithink you have your own supermarket because you are having all by the way I like you 👍👍👍👍👍👍👍👍👍👍

Awesome i like that

is amizing

Cool, only the battery under load will be heated where will this heat go?

you is genius

Those welds tho 😂

Where are you get hub motor and IC please give link

Excellent job done!😀👌👍

Eres un genio.... Felicidades.

Amazing video 👍👏👏👏👏

nice

I hope I have store room like you 😈😈😈

i love creative channel and i love this video

Hi, did you use only one ESC for 4 motors?

Good idea and nice video 😍👍♥️

Worlds Greatest Dad

Incredible Work

Please make electric drift trike with that motor

Please set up tour

Nice welding!!! 😂

Very nice making

dude I'm watching videos, admiring ;-)

Motor link

Powerful peoples come from powerful places.

I love creative challenge and you are very super

Amazing bro....

Where u get the 2in1 saw

Amazing. Thanks for share. We expect more...

Lovely work bro nice

HEY PLEASE MAKE A 775 MOTOR JIG SAW

You are so talended

Great project

Vc e topp

nice...

Когда уже будет четыре миллиона под пищиков ???👋

GOOD JOB BRO

And nobody noticed he mounted the side motors in parallel...