BUILD A Homemade DIY FARADAY CAGE for EMP Prepping, Signal Blocking & EMF Health! MIL-STD Certified!

Рет қаралды 66,076

Күн бұрын

BUILD YOUR OWN CUSTOM FARADAY CAGE! Box and Faraday Materials list/links/instructions below
**CHECK US OUT ON:
• Instagram: / missiondarkness
• Facebook: / missiondarkness
• Twitter: / missiondarkness
• Website: www.mosequipment.com
Buy supplies on Amazon now: www.amazon.com/stores/page/2F...
Build your own homemade DIY Faraday Box with products that are certified MIL-STD-188-125 compliant (mosequipment.com/pages/compli.... A simple and easy way to own and protect your privacy as you store devices, electronics, generators, and more inside! Stash in the back of your car, garage, or anywhere. Don't be hacked or tracked, make a RF signal blocking faraday box to avoid identity theft, GPS tracking, EMP, EMF, EMR, EMI, WiFi, Bluetooth, Cell signal/networks, 5G, Radiation and more.
MATERIALS LIST & SPECS
- Size: 24" x 24" x 18"
- Total Time: 3-4 Hrs
- Total Cost: About $275
- Plywood Box -
• (3) Quarter sheets (48" x 24") of 1/2" plywood
• (1) 2" x 2" x 8’ Pine board (or similar low-price wood)
• (2) Lockable Draw Latches (3 1/2")
• (1) Utility Pull (5 1/2")
• (2) Door Hinges (4")
- Faraday Supplies -
• TitanRF™ Faraday Fabric Pro Construction Kit (6 yds (mosequipment.com/collections/...)
• TitanRF™ Faraday Tape (2.5" x 10’) (mosequipment.com/collections/...)
• TitanRF™ Faraday Gasket (1/4" x 3/4" x 90") (mosequipment.com/products/tit...)
Buy all Faraday supplies on our website or Amazon: mosequipment.com • www.amazon.com/stores/Mission...
For custom materials, comments & questions, please email us at info@mosequipment.com or call 805-318-3212

Пікірлер: 98

@Nuts-Bolts 3 жыл бұрын

Beware. Unless the EMP is originating in somewhere like Florida and this box is in somewhere like Alaska, it wont be any good for your consumer IT equipment. Whist the MIL-STD-188-125 spec has a 20db safety margin (60db + 20db = 80db), this is considered the ‘minimum’ for military spec and other commercial equipment which is designed to be tolerant to 200 v/m or above. Consumer IT is very seldom better than 10 v/m. Also, with the Earth’s weakening magnetic field, it is expected that future major solar flares will have energies which far exceed the MIL-STD-188-125 spec (something which the US military is still well behind on for mitigating in it’s field equipment) . So a thick and conductive metal enclosure is a must for efficacious prepping and ideally stored below ground. I think that this serious limitation should have been pointed out in this (and other similar KZfaq) videos on this topic.

@missiondarkness 3 жыл бұрын

Great comment. We highly recommend items kept inside a faraday enclosures to be wrapped in faraday material as well for optimum protection and RR, EMP, EMF, EMI, EMR, and CME shielding. Our products are

@etana6034 2 жыл бұрын

What do you suggest instead?

@andreah6175 2 жыл бұрын

As a victim I can attest they got/tap into energy nobody knows about, this is what one of the weapon mark imprints look like. I'd like to know how to block it but its diverse and not the same method of attack on any given day. Their energy can go thru any objects to precise locations. kzfaq.info/get/bejne/ic6arNCSl86XYmQ.html

@apacalyptic1freelancevideo823 Жыл бұрын

Thats what she said

@-djg-3955 8 ай бұрын

Sir this may be an out there question but in theory can someone line a large closet w faraday fabric and seal it in compromised segments to protect a larger indoor area?

@sandroitsme2560 Жыл бұрын

I've had a faraday cage for a dozen years and it's a big metal galvanize trash can with all kinds of back up equipment like a solar controller, walkie talkies, ham radio, backup laptop, etc. Each item is either in a cardboard box or wrapped in thick paper. Much easier and not as expensive...

@jeromekelly477 3 жыл бұрын

Great info - thanks. Excellent presentation too.

@Anthonybrother 3 жыл бұрын

Good tutorial and your replies to comments are pretty useful, thank you for sharing your knowledge.

@PreparedOverlander Жыл бұрын

I have built a few faraday bags and boxes. I have used 3 layers of material for my bags, then placed them in a box that also has 3 layers of material. I am nesting items in multiple ways to give a better result, hopefully.

@mathewscoines8219 2 жыл бұрын

Thanks for the video - made this myself over weekend - works perfectly ! 👍

@andreah6175 2 жыл бұрын

Won't help for things like this kzfaq.info/get/bejne/ic6arNCSl86XYmQ.html

@jacobwebb2308 6 ай бұрын

Great build! Great video!

@lmbakerracing 2 жыл бұрын

So if it’s so conducive, you had already wrapped your wood blocks with the fabric, the put them on with metal screws which would be exposed from the outside,. If the material is that conducive it would allow anything from the outside a direct pathway to the protected center

@heru-deshet359 5 ай бұрын

I'm going to EMP proof my garage where all of my essential electronics, wi fi and generators are.

@richardpatton4197 Жыл бұрын

Great details. Thanks for sharing. Anything wrong with using an aluminum garbage can with aluminum tape for the seams and using emp gasket on the lid closure? Also, will the devices inside your box need to be protected from emp current since the inside of the box is conductive?

@sembutininverse 3 жыл бұрын

thank you 🙏🏻

@chelseafcfc 3 жыл бұрын

Nice bro thanks for looking out for us 👊

@Subgunman 5 ай бұрын

Prefer an aluminum NEMA electrical box. They can be ordered with conductive gaskets that are very effective in providing a decent contact between the lid and container. You will have to place an insulating layer on the inside of the container so equipment cannot contact the metal case. You must also ground the cabinet with a grounding cable of at least number six high strand count cable that is used for high end car stereo installations. The ground cable should be kept as short and straight as possible to a decent ground rod at least 6 to 8 feet long. Some have tried to ground the containers to water lines however in todays modern homes the water main line coming into the home most often is made of plastic. Will not work. Some people will drill a hole through the concrete floor in their basement in an area away from any drain lines exiting the home. One must also keep the ground stake about 12 inches out from the wall to avoid hitting the foundation and drain tile that is placed under the floor around the perimeter of the basement. They also place the box about 2-3 feet above the floor on a shelf. As you drive the ground rod into the earth around the last 8” it’s a good idea to use a mould resistant silicone sealant around the rod and a 4” section around the rod to seal it from any moisture coming up from the hole.

@gkingdiamond 3 жыл бұрын

This is the best faraday box I've seen...thanks! So if i build it the way you presented, I can put the electronics inside without having an additional internal box? Wouldn't the EMP charge hit the faraday material and damage items that were in contact with it?

@missiondarkness 3 жыл бұрын

Glad you like the video, Gary! Thanks for watching. It is best if it's grounded, so you could always attach a conductive item (like a stainless nail) through the box and run it to ground. You could also add a thin layer of non-conductive material on the inside, such as cloth. Generally speaking, the charge from the EMP should circulate through the outside of the material (if it is in fact a full faraday cage) and not penetrate inside with enough power to create damaging effects on the electronics. This would be the point of the faraday cage. It's obviously hard to test these effects in the real world (we do actually perform lab testing to MIL STD 188-125 for HEMP on our materials and products), so many people in the community just take the approach of doing as much work as they can to protect their items within reason. So, all that to say, if you want to ground it and insulate, do it! Haha, hope that helps.

@Anthonybrother 3 жыл бұрын

@Mission Darkness To insulate the box with a nail, it needs to be in contact with the faraday fabric from underneath, not nailed through it, right?

@Anthonybrother 3 жыл бұрын

@Mission Darkness I meant, to add an electrical ground to the box.

@SanctuaryLife Жыл бұрын

I would line it with rubber just in case

@qball4life2 Жыл бұрын

Do you have a video on putting that box together? I have EVERYTHING on the list but no video on that. Do you have a link on that one?

@user-7lf7w 6 ай бұрын

Thank you for this video My question is more for a scientist, how do we know when it is safe to open the box in case of Sun solar storm creating EMP

@jungleghostsurvival 11 ай бұрын

Can you use a chest freezer for faraday modified with emp cloth

@klwilliams1958 2 жыл бұрын

Could you line or wrap a cardboard box with the titan fabric? Let's say it shoe box. Would it have a tight enough seal or could wrap with large rubber bands to have a tight seal?

@markburks9084 2 жыл бұрын

I'm looking to add Solar to an RV, and the battery bank, inverter and everything else must be installed under the king bed. I want to protect my wife and I from electromagnetic field from the inverter for sure. Do you think this would work for us?

@dixievixen6045 2 жыл бұрын

I was getting ready to order some of this material to make a cage for a solar generator but decided to watch this first. Now, I am really a bit confused. I thought that the items placed inside the cage/box needed to be shielded from direct contact with the shielding material. My plan was to protect the material with a bit of cardboard cushioning and sit the generator on the cardboard. Reading another comment and your response, it sounds like whatever you put in needs to be in contact with the shielding material. Is that correct?

@andreah6175 2 жыл бұрын

As a victim I had learned the material must be grounded for it to work. If its only electronics to protect I can't see how a steel box itself wouldn't be effected kzfaq.info/get/bejne/ic6arNCSl86XYmQ.html

@jimmybrown9039 10 ай бұрын

can you wrap the outside with aluminum foil several times and work

@apacalyptic1freelancevideo823 Жыл бұрын

good to know

@matthew504 4 ай бұрын

Is this material meant to be conductive or to block conductivity around it? I'm seeking to understand where the emp is supposed to interact with this.

@GoonShenron 3 жыл бұрын

Could I repeat the tutorial but with a metal box? I’m thinking of purchasing a diamond metal toolbox and double wrapping it with the faraday fabric you purchased.

@missiondarkness 3 жыл бұрын

Absolutely. You can use any material to create a faraday enclosure/box/cage. As long as you use the correct amount of faraday fabric and layer it so that it remains touching and conductive throughout the structure, your design should block signal.

@benwillard6751 8 ай бұрын

Nice job and very nice box. However, the expensive is ridiculous. I hope there are way cheaper alternatives.

@Uncle_Buzz 7 ай бұрын

What about grounding? Wouldn't that would need to be bonded to earth ground for it to work?

@selahr. 3 жыл бұрын

Could a prefab metal tool chest be converted to a faraday cage? Seems like the EMP gasket material would be needed and a liner, but overall price seems like it would be less than fabric for the same storage capacity on wood?

@missiondarkness 3 жыл бұрын

Yes you can certainly take any box and line it with faraday fabric including a metal tool chest! Just make sure you place the gaskets on the edges correctly so that they are conductively touching one another and with the lined fabric when closing, otherwise, the box won't work.

@ron7107 2 жыл бұрын

@@missiondarkness why would you need anything other than a metal box with insolation on the bottom ???

@scriptmaster3357 3 жыл бұрын

So is it possible to build a faraday box whereby you can put a small generator within it and still be able to run the generator while protecting it from EMPs at the same time? Didn’t know if that is possible and how you could get around the fact of needing an exhaust opening and an air intake opening as well.

@missiondarkness 3 жыл бұрын

Yes, you can definitely build a faraday box that has filters for running/charging generators and vents for allowing exhaust to circulate in and out of the box, all while protecting against EMPs. You must use specific faraday EMP blocking filters and vents to keep shielding conductivity within the box. Here is a video on how to install a filter for your faraday cage: kzfaq.info/get/bejne/heBloM5o2tC0e5s.html and here is a video on how to install a vent into your faraday cage: kzfaq.info/get/bejne/ftKaltCTvaipf4k.html

@danielmorrison7579 Жыл бұрын

Since you are doing this to a box with solid walls, why not simply cover the inside with Al foil? That would achieve the same effect, and be much cheaper as well. That fabric is great for situations where you need the flexibility, but here, you do not.

@wwolaniuk 7 ай бұрын

Why would you put the material on the inside of the box next to the electronics you are planning on protecting?

@lusnorthernhome3410 2 жыл бұрын

Could you line a tool box?

@lynette06grissom83 2 жыл бұрын

I'm jus curious dose the 2x2x8 dose it specifically have to be pine board

@helennethers9777 5 ай бұрын

if i do a box where one side is open (for the back of a computer desktop tower) will the front area get protected by a directional electromagnetic pulse?

@peterstoops5683 7 ай бұрын

could you use glue instead of staples?

@nebulousJames12345 2 жыл бұрын

I wish I could tell if this was a reputable video. Thx for removing those dislikes though youtube.

@frankienerdyboy 2 жыл бұрын

352 to 9 dislikes. Just get the plugin.

@SanctuaryLife Жыл бұрын

What about ELF radiation, is that is a risk in an EMP attack? Titan doesn't block ELF, you need a product such as MuMetal to do that. Or could you use solid aluminum to block ELF does anyone know if it's a risk?

@calvinledford9606 3 жыл бұрын

Big issue - the materials list is flawed. It specifies "6 yards" of the fabric, but the website only sells fabric in in precut lengths measured in feet and inches and marketed with names that provide no real help - such as pro construction kit, pro construction kit 20, etc. I called to ask which I should order and customer service staff didn't know either and suggested I might want to order the next size larger fabric "just in case) - which is a whopping $290 dollars more then the size below! Discouraging when trying to order and have no idea what to get. Otherwise a cool project.

@missiondarkness 3 жыл бұрын

Hi Calvin! I just talked to Kees - he was the customer service rep who you spoke with on the phone. Kees tried to say the fabric comes in 6 yard lengths, which can be purchased on the site. Sorry if we weren't very clear on that. The 6 yard size is called the Pro Construction Kit, and here's a link. mosequipment.com/collections/faraday-supplies/products/titanrf-faraday-fabric?variant=27931162443878 If you look above in the description of this video there are also links to each item. I hope this helps. Please let us know if you have any more questions and we will do our best to respond. Thanks - Ryan

@terryqueen3233 2 жыл бұрын

I have a metal tool box that I'm not using anymore how can I use your product to ensure a good RF block??? Most people never answer questions I certainly hope you do.

@tims244 11 ай бұрын

Just make sure to use a gasket, or use metal hvac tape around any holes or seems, put some sort of rubber insulater or card board in it after so none of the devices touch the metal

@tellingtruth247 2 жыл бұрын

Where can I get fabric

@vincentmontagna1711 3 жыл бұрын

Hi, you used Google App if I'm correct.? When you pulled the phone out of the Faraday box the app was still running? Correct me if I'm wrong, how would the app still be running if there phone shut down? Doesn't that mean that all apps can only be running if the phone is still getting signal?

@missiondarkness 3 жыл бұрын

Hi there, apps can run inside the box, however, if they need a wifi or cell connection to function, they will not operate because cell and wifi signals will be blocked from your device. Our app is available to download off of google or apple, however, it does not use internet connection once it is in use and stored inside the faraday cage. What our app tests for is when cell and wifi signals are lost on your device, it records the process without using any outside source.

@frankienerdyboy 2 жыл бұрын

The box blocks signals from entering the box and reaching the phone.

@flaxensaxon6052 3 жыл бұрын

Can i line the inside bottom/ sides of the completed box with cardboard to protect the fabric?

@missiondarkness 3 жыл бұрын

Yes you can! As long as your box is still conductively made with faraday fabric and your devices are 100% enclosed within the layers when stored inside the cage, you can put anything up against the fabric to protect it. Make sure once you seal the box that the closure section is also conductive and there is no barrier in between the layers of closing fabric.

@mentonparticles7052 2 жыл бұрын

@@missiondarkness I am confused, I thought the material being protected, like a cell phone, should NOT be in contact with the conductive material because the conductive material is routing the EMP away from the phone. If the phone is in contact, it'll just get fried, is that not correct?

@kennashouse5973 3 жыл бұрын

Isn't the exterior of a faraday box supposed to be conductive, and the interior insulated (i.e. non-conductive)?

@missiondarkness 3 жыл бұрын

Good question! It is very possible to reverse the conductive area to the exterior rather than interior. It works both ways and as long as you have designed a conductive area with faraday fabric and have made the exterior fully covered and conductive when you close the box, you can store your devices inside and signals should be blocked. Designing and lining the interior with faraday fabric to be conductive allows you to use other material like leather, paint, etc. for the outside style of the box/enclosure and will also reduce tear and wear that lining the exterior of the box could experience. Let us know if this answered your question!

@needparalegal 3 жыл бұрын

Cheaper to buy a steel box.

@vincentmontagna1711 3 жыл бұрын

Why can't you use glue instead of Staples and plastic drywall bead instead of metal?

@missiondarkness 3 жыл бұрын

Hi Vincent. The reason we recommend not using any form of adhesive other than faraday tape or other faraday adhesives is because in order for the box to block 100% of all signals, it has to be a fully conductive enclosure built with faraday materials. The material is made out of a copper and nickel compound that is conductive when it touches other pieces coated in that material. If you use glue or other non-faraday adhesives, signals will be able to pass through them and you will have signal leakage in your cage.

@onlyemoney 3 жыл бұрын

What’s the point of the cage for the router if it’s just going to block the WiFi don’t u need the WiFi?

@missiondarkness 3 жыл бұрын

We've definitely had lots of discussion regarding this question. The simplified answer is that some of our customers concerned about EMFs have consistently reached out to us asking how to shield your router when it's not being used. This is a solution for how they can shield EMFs coming from their router without having to turn off their router and go through the rebooting process every time.

@SalamanderFangskin 3 жыл бұрын

Why didn't you put the fabric on before assembling the box?

@missiondarkness 3 жыл бұрын

Good question! I could have wrapped the individual panels with fabric before assembling the box, and that could have worked well for this style of enclosure (though it’s still best to tape the seams). The reason I lined it is to show how that process works, as many people have much larger enclosures like sheds. The concept of wrapping around corners takes a bit of technique that I tried to demonstrate on a smaller scale. Thanks for commenting!

@SalamanderFangskin 3 жыл бұрын

@@missiondarkness oh, I understand. I'm new in to this so I didn't know the the different purposes of the tutorial. thanks for the reply!

@kristinachilds8270 3 жыл бұрын

Is it possible to sew the fabric closed at all the corners?

@missiondarkness 3 жыл бұрын

Absolutely. As long as the faraday fabric is touching and creates a conductive enclosure, you can seal it however you'd like, however, we recommend taping or patching the fabric with our faraday tape/patches for optimum conductivity.

@kristinachilds8270 3 жыл бұрын

@@missiondarkness I had another question about that. The glue of the tape doesn't interfere with the conductivity of the fabric? I would imagine the glue adds a small buffer between the two fabric layers

@Anthonybrother 3 жыл бұрын

@kristina childs Pretty sure he uses special electric tape with which that's not a problem.

@armyscout7600 5 ай бұрын

Why not make the fabric thicker so you don't have to do 2 layers?

@ron7107 2 жыл бұрын

just wrap in chicken wire and aluminum foil and go fishing

@emlo40 3 жыл бұрын

people wasting money and emp prof enclosures me knowing that the local mall is a black hole for any radio wave

@Anthonybrother 3 жыл бұрын

What a genius. I hope you enjoy your career of working at McDonald's.

@maggiehumble7822 2 жыл бұрын

Mylar bags

@amandamarie5337 11 ай бұрын

Two layers?? Why two?

@imonlyhalfnutsreally2113 3 жыл бұрын

To Chives, yes, that's the right way to do it.

@ron7107 2 жыл бұрын

How to build a box,,, ok

@vincentmontagna1711 3 жыл бұрын

Can you show us without an app??

@missiondarkness 3 жыл бұрын

There are not many ways to show how signals are blocked from your device because signals are not visible. Our app records if cell/wifi connection is lost, therefore showing how the faraday blocks signals from your device once sealed up. Another way to test if signals are blocked is to video record your phone screen and see it loose connection to wifi/cell. You can also test this method out by making a call to someone who has their phone stored inside the cage, it won't go through.

@mycosys 10 ай бұрын

@@missiondarkness its called a spectrum analyser - you know this!

@stretch8861 3 жыл бұрын

Faraday cage/Schrodinger's box. My phone simultaneously has and does not have reception in the box, I won't really know until I open the box to find out! HAHA! Dumb physics joke. Sorry, not sorry!

@reelactionreaction 3 жыл бұрын

Put a radio inside and turn the volume up close the lid and if you don't hear the radio it doesn't mean the wood is blocking it it means the signals blocked.

@bobjackson7516 3 жыл бұрын

@@reelactionreaction In addition, put a cel phone in the box, call it from another phone. Then, open the box and see if you have a missed call. If you do, it had signal, if you don't it didn't.

@ronnietexan 8 ай бұрын

Well, if you ever wish to make a job far more complicated than necessary just ask this guy how to do it. Took twice as long and used far more product(s) than truly necessary. Well, if you're selling the products it's best to show how to use as much of it as is unnecessary, LOL!

@mycosys 10 ай бұрын

Its a great pity you didn't do any meaningful testing at all. A phone will lose reception way before meaningful attenuation is achieved in either the OpSec or Device Safety context.

@heinzhubbuch9409 2 жыл бұрын

WAY OVERBOARD TO MUCH WORK.... JUST GO TO YOUR LOCAL THRIFT STORE AND BUY A METAL BOX FOR $2....

@ruidadgmailcanada8508 2 ай бұрын

Nest your devices with a few layers of faraday cages. But reality is that your stuff will fry. 🤷‍♀️ Weakened and weakening magnetic field now allows much more solar radiation and cosmic rays through to us. Yay cancer! 😅 So a foreign or domestic EMP, could possibly be defensible. But a solar CME or worse another micro-nova will fry everything regardless of faraday cages. The amount of energy melt s surface level conductive metals through induction. Good news is that we won’t be around either. Forecast is mid 2040 for cataclysmic solar events…if we don’t nuke ourselves 1st. ☠️ 😅