Build my own Audio Tube Tester - with schematics (Re-upload)

No video

Build my own Audio Tube Tester - with schematics (Re-upload)

Рет қаралды 8,015

Күн бұрын

Audio Tubes getting expensive and rare now. Always wanted a simple affordable Audio Tube Tester. Simple easy ...n o fancy. I did it. Give me a thumps up if it inspires you to anything!
Schematics 04:04 and Part list 03:11 included.

Пікірлер: 22

@jeffv.akaonsjeffke9865 Ай бұрын

very nice build, looks like a cool and well fuctioning aparatus. Great job !!!

@javic5119 3 күн бұрын

Muy buena construcción,felicidades gran trabajo, gracias por compartir ❤

@kirkdecker6228 Жыл бұрын

Whoa! Nice to see another video of yours!!

@bretfuzz925 6 ай бұрын

Thanks for the video! I was thinking about building something like this a couple of days ago.

@MrJLobster 6 ай бұрын

Thanks for your comment! I´ve wired in the missing standby switch later at the end. It was dearly needed in this case - so if you plan on making your own one - don´t skimp on that one!

@Pulverrostmannen 9 ай бұрын

I have built a complete audio hifi system using tubes from pre-amp to power output from scratch, VU monitor and everything. I got 2500 hours out of JJ EL34 standard version tubes even if I push them hard with dynamic voltage controlled power supply I built myself ( it is an external perfect DC stabilized adjustable supply from 200-500 volt that also is audio controlled which can be externally triggerend and apply power when something is playing, so at idle the power amp has it´s built in supply that works around 250V so it saves tube life when nothing is playing, and with the external supply I can crank up the power enough to redplate the tubes for maximum power, good stuff

@songshineoriginalmusic 7 ай бұрын

that's pretty cool

@Pulverrostmannen 6 ай бұрын

@@songshineoriginalmusic thank you :) I really should do some videos on this stuff sometime but I been really slow with that part for many reasons. But I really like this system and those who see and hear it in real life is very impressed too. I always loved tubes

@songshineoriginalmusic 7 ай бұрын

I like your form factor. Of course a solid wood like walnut would look nice too. Looks like you could resell them or sell a kit. Nice tight wiring. Kudos!!

@acoustic61 Жыл бұрын

Very nice! You probably could've made is simpler too by eliminating the "Test" mode and "Measure" everything.

@tedcollins4684 Жыл бұрын

Excellent

@akrjp6857 7 ай бұрын

ok , thanks , have a good day. Alain

@ebones6957 5 ай бұрын

Love it!

@tanmeowsoon6992 2 ай бұрын

Hi Sir Good day can share with me your drawing where i can learn from you , Many Thanks, Tan MS

@MrJLobster 2 ай бұрын

Hallo! The Schematics on 04:04 and part list at 03:11 is all I got. There maybe has to be some experimentations to be expected so..Take care, good luck!

@akrjp6857 7 ай бұрын

ok thanks for the answer , do tou think it is possible to test tubes only with a multimeter ?

@MrJLobster 7 ай бұрын

No that wouldn´t be very meaningful apart from discovering a fatal short to grid or an open heater filament.

@akrjp6857 7 ай бұрын

thanks for this video , yes that"encourage me to do the same or similar , but could you telle me what was the total amount in " €' ( or ' £ " or " $ ' ) to do it ?

@MrJLobster 7 ай бұрын

thanks for your comment! ..thats a good question. Apart from the chassis parts I had lying around I invested around 140€ for the essential parts. The big resistors and things like tube sockets and switches and quiet a bit of shipping fees not included. So I think it was not cheap. I would definitely recommend to install a heater standby switch... which I had non at the time but I installed it afterwards. So good luck, have fun diy and take care !