Build the ultimate table saw sled, FAST with the New and Improved ZeroPlay 360 Sled Kit!

Рет қаралды 41,615

Жыл бұрын

Order here: www.microjig.com/products/360...
The new and improved ZeroPlay 360 Sled Kit combines the precision and ease of the ZeroPlay Miter Bars with the MatchFit Dovetail Hardware to create the most versatile sled in the workshop, allowing woodworkers to make accurate, safe crosscuts with a table saw. To create a custom sled, simply cut plywood to size, route dovetail grooves with a ½-inch, 14-degree dovetail bit and install the ZeroPlay Miter Bar.
The ZeroPlay 360 Sled Kit includes one ZeroPlay Miter Bar and the new MatchFit Dovetail Hardware Variety Pack.
Please Subscribe! bit.ly/MJTubeSubscribe
Our Facebook: / microjig
Our Instagram: / microjig
Our Twitter: / microjig
Our Blog: www.microjig.com/blog
Our Website: microjig.com
Our Newsletter: microjig.com/newsletter
We love getting new ideas from our community. Whenever we get clever projects and plans from our friends around the world we want to make sure everyone benefits to work safer and smarter.
Products we used:
ZeroPlay 360 Sled Kit: www.microjig.com/products/360...
Find one near you: bit.ly/WhereToBuyMicroJig
MICROJIG.com
Work Safer. Work Smarter.

Пікірлер: 19

@DavidBelfortNews Жыл бұрын

As a beginner I appreciate that the video shows how to overcome a small router table limitation for the 8" grid cuts.

@Microjig Жыл бұрын

David, our pleasure! We try to keep in mind that not everyone has all the cool toys...yet! :)

@AngieWilliamsDesigns 10 ай бұрын

I love this system

@pnwgrown_360 Жыл бұрын

That’s a very intelligent design

@Microjig Жыл бұрын

Thank you, we are pretty proud of the 360 Sled design and the new ZEROPLAY Miter Bar that can now be setup and adjusted from above the table.

@artdaedelow8108 Жыл бұрын

Great presentation which sold me on making one. Should some type of finish be applied to the wood? WELL DONE!! Thank you.

@Microjig Жыл бұрын

Art, Thanks for the kind words! A light coat of shellac is my go-to for jigs and sleds. Or even just paste wax. You do not want too smooth a finish because a little friction helps clamping parts firmly in place.

@hooker4749 7 ай бұрын

nice

@Microjig 7 ай бұрын

Thanks! We think so too.

@jtlong8383 Жыл бұрын

At 6:49 your instructions say to clamp the base to the face of the fence. Are you supposed to glue it prior to clamping? Also, how do you square the fence to the saw blade? Since it is not permanently attached to the sled base, I assume you must square it each time you want a 90 degree cut? This is probably the most versatile sled I’ve seen, but squaring the fence at 90 each time you use it makes me want to make a dedicated version with a fixed rear fence.

@Microjig Жыл бұрын

JT, yes, glue the fence base to the fence face when you clamp it. Second, you are correct, the fence has no presets, so you do need to square it for 90 degree cuts. If you square the base edge to your fence, then a good quality Speed Square will let you rapidly set 45 and 90 degree cuts. I actually use an inexpensive digital bevel square (about $30.00) to set my fence. It has the advantage of being able to set any angle very precisely. The problem with a fixed rear fence is that it will greatly restrict the ability for rotating of the 360 fence.

@dianetakis3712 Ай бұрын

I have a SawStop table saw which tilts to the left. Should I use the right miter slot for the sled?

@Microjig Ай бұрын

You certainly can, especially if you plan on cutting parts with the blade angled. Pretty much all modern table saws are left tilt now. I generally do not use my 360 Sled with the blade beveled, so I use mine on the left.

@imowfaces412 Жыл бұрын

What's the difference between this sled and the ultimate sled

@jamesvandergriff5204 Жыл бұрын

What was the point in the adjustment I’m the beginning if we just reverse it in the end and put it at the narrow point?

@Microjig Жыл бұрын

First, at 4:22, you are adjusting the ZEROPLAY Bar itself to fit your miter slot. This is using the supplied hex wrench on the button head screws. Later, at 4:55, you are squaring the sled to the blade/miter slot using a screwdriver to loosen and re-tighten the mounting screws. Two different adjustments. If this was not what you were asking, please feel free to email us a support@microjig.com or call us at (855) 747-7233 and we can answer your question.

@artdaedelow8108 Жыл бұрын

Should a finish be applied to the finished sled?

@pablor3138 Жыл бұрын

Looks extremely complicated to make? Does anyone just sell them?

@Microjig Жыл бұрын

It is actually easier than a standard cross cut sled to make, and is very versatile. Building sleds, jigs and fixtures for your shop is also an excellent way to improve your skills as you improve your shop. We do not currently make the sled for sale.