How To Build a Fast + Reliable GO KART!

Рет қаралды 176,077

Күн бұрын

This is a full in-depth video of installing a Live Axle Kit and Billet parts onto our vintage #gokart project. These parts increase performance and reliability (and they look cool too) Together these modifications are our favorite upgrade for any kart!
----PARTS LINKS----
(Build Break Repeat is proudly sponsored by GoPowerSports)
Live Axle Kit (we used 36”): www.gopowersports.com/6-live-...
Billet Rod: www.gopowersports.com/predato...
Billet Flywheel: www.gopowersports.com/arc-spe...
22lb Valve Springs: www.gopowersports.com/22lb-va...
Sprocket Hub: www.gopowersports.com/1-sproc...
22mm Mikuni kit x1: www.gopowersports.com/22mm-mi...
Header x1: www.gopowersports.com/header-...
6” Floater Wheel, No Offset, 5/8 Bearing, 13x5-6 Turf Tire x3: www.gopowersports.com/13-x-50...
Clutch, 10T 420 Chain x1: www.gopowersports.com/10t-3-4...
54T Sprocket x1: www.gopowersports.com/sprocke...
Drum Brake x1: www.gopowersports.com/4-brake...
Pedals x1: www.gopowersports.com/vintage...
Brake Cable x1: www.gopowersports.com/60-brak...
Brake Band x1: www.gopowersports.com/4-manco...
Brake Band pin x1: www.gopowersports.com/brake-b...
Throttle Cable x1: www.gopowersports.com/75-miku...
Engine Mount x1: www.gopowersports.com/engine-...
Steering Wheel x1: www.gopowersports.com/steerin...
¼” Self-Tapping Bolt x2: www.gopowersports.com/self-ta...
----PARTS USED (AMAZON AFFILIATE)----
Orbital Sander- amzn.to/3XaEB9r
Krylon Gloss cherry Red - amzn.to/3qQH6BE
2k Clearcoat - amzn.to/3qOi4mX
Self-Etching Primer - amzn.to/3X9vB4o
Gloss Black Enamel - amzn.to/3JhT26a
Grip Tape - amzn.to/3NySiMi
Vinyl Seat Fabric - amzn.to/3PmgvHb
Seat Foam - amzn.to/3JgCStA
LINKS TO OUR NEW TOOLS AND EQUIPMENT: linktr.ee/BuildBreakRepeatCha... (Amazon Affiliate Links, if you buy something using our links it will help the channel!)
----TOOLS ----
Tools we use from our channel partners:
HOBART Welding Equipment
www.hobartwelders.com/
Texas Metalworks 40x80 Welding Table
texasmetalworks.com/product/f...
RogueFab Tubing Notcher
www.roguefab.com/product/vers...
SWAG Offroad PortaBand Table
www.swagoffroad.com/products/...
Optrel Grinding Mask
usa.optrel.com/en/products/au...
• Andrew Applepie - Jimmi
----SOCIAL MEDIA----
CHECK OUT OUR INSTAGRAM! build.break.rep...
----MERCH----
MERCHANDISE CUSTOM DESIGNED BY YOURS TRULY
teespring.com/stores/build-br...
---------MUSIC --------
Background Music -Epidemic Sound Library
Intro Song - Jimmi by Andrew Applepie
Intro 0:00-0:15
Disassembly 0:15-2:31
Engine Build 2:31-6:14
Engine 6:14-11:31
Live Axle 11:31-13:47
Drive + Finale 13:47-17:10

Пікірлер: 65

@CarsandCameras 10 ай бұрын

Hitchhikers are bad this time of year!

@BuildBreakRepeat 10 ай бұрын

You’re telling me, he didn’t even wash his hands before shaking mine 😳

@lacehepbourn1035 9 ай бұрын

Love both Shows.... Huge fan of Ike!!!

@johncarlson8029 3 ай бұрын

Hey guys, name is John, Rachael gets my parts for me here in Plymouth. I need a good vintage kart to restore and she keeps forgetting to ask you guys for me. I am not a groupie i am 59 retired mechanic and need a project worthy of restoration, can you guys help?

@fredericrike5974 10 ай бұрын

Sorry for you loss, guys. Adventure buddies are always special. As a matter of fact, all of you lot were headed off to college a bit back; an update, if you would. Always awesome!

@LSandL31 10 ай бұрын

So sorry for the loss of Buddy!! Well done on the build!

@nashguy207 10 ай бұрын

So sorry for your loss. They become so much a prat of the family. I know how hard it is. Been through it my self. God Bless!

@BuildBreakRepeat 10 ай бұрын

Couldn’t have said it any better, we appreciate that!

@badad0166 7 ай бұрын

Great crosspromotion with some stellar acting. Well done! Light a match!

@blainehale 10 ай бұрын

That last scene with the train is really great! I bet y'all were happy to capture that.

@santaclause2875 10 ай бұрын

Another great build, another great video!! Fun to see Ike, he's a total hoot! When you can, give us an update on Daniel. Soooo sorry about Buddy. Oh my God, I understand the pain. RIP Buddy. Hey, been watching you guys since 'day one'. I'm soooooo proud of you guys and your accomplishments. With all the foolishness going on in America these days, you all give me HOPE for the future!!! Keep on truckin' !!!!

@BuildBreakRepeat 10 ай бұрын

Thank you so much, we can’t say how much we appreciate you sticking with us from the beginning! We have plenty in store and Daniel will be making a couple cameos in the not so distant future

@santaclause2875 10 ай бұрын

@@BuildBreakRepeat That's super !!!

@bryduhbikeguy 10 ай бұрын

It looks so good,and moves pretty well.Would you show building an exhaust support so bumpy areas don't snap the header off?Thnx. So sorry for the loss of Buddy. You guys gave him some great memories too.

@Cyruscosmo 8 ай бұрын

A tip for holding valves closed. Place about two feet of 1/4" braided nylon rope inside the cylinder, then roll the piston up towards TDC till it stops. The rope inside the cylinder will hold the valves closed and not scratch up the inside of your cylinder. Leave a few inches outside the cylinder so you can remove it easily after you finish replacing valve springs. So Sorry for your loss, RIP Buddy.

@TundeEszlari 10 ай бұрын

You are a very good KZfaqr.

@meco72104 10 ай бұрын

Cool little cart, nice build.

@mikhailjairnisbett441 10 ай бұрын

Great video! Was any clearancing required to install the rod? I've seen some people need to do it before on the 224. (Nvm I see now that it's a 212 with a red flywheel cover)

@user-kg6zz9vv5w 4 ай бұрын

It is a bit of a vintage go kart but I highly doubt it's a streaker,,someone probably put the streaker steering wheel on it at some point,looks to be a "Clark" brand go kart to me,,if it still had the aluminum square shaped pedals on it that would be a dead give away its a Clark brand,,and I've seen a ton a streaker as I live only 2 hours away from were the Ken bar"manufaturing plant used to build them in north georgia,,I know it can be hard identifying older go karts for sure it's a hobby of mine,,nice rebuild job 👍

@satt131313 5 ай бұрын

Yes you can hear it just wanting to keep pulling. Will definitely go crazy in the dirt.

@doncook5221 9 ай бұрын

Watched both of your videos on this kart and really enjoyed them both. What would be really cool would be to do a video on stretching the frame. Just sayin......Keep um coming.....

@chrisbillmeyer8344 10 ай бұрын

Lol, what the heck Ike from cars & camera’s doing here.?!

@phazelord3527 10 ай бұрын

Same thing I was thinking about that cameo. Thought I was having a stroke

@orlinchirinos1981 10 ай бұрын

😂

@OakblockBuilds_REDLINE 6 ай бұрын

Wasn’t expecting that 😩😂😂😂

@bucephalus14 10 ай бұрын

Sorry about your puppy brother. They really are man’s best friend and can be so pure. Wish they could stay forever

@heathot877 10 ай бұрын

please do a front brake kit next

@VehiclesDaily 8 ай бұрын

very underrated

@Adub86 10 ай бұрын

RIP buddy. Us, as humans, don’t deserve dogs. But I’m glad we have them.

@BuildBreakRepeat 10 ай бұрын

You sure are right about that!

@metrofarmboy2926 10 ай бұрын

Sorry for your loss guys,he was a good boy!

@j.s.hutchens7623 6 ай бұрын

How satisfied are you with the band brake?

@Youhaverights6 9 ай бұрын

Was the stock rod Cast aluminum because it looked stock billet to me?

@nilla003 Ай бұрын

Used the stock camshaft? So most of the gain was due to the flywheel?

@ignolimt6570 3 ай бұрын

what motor does it have and how much mph and ps

@johnkoelliker8480 10 ай бұрын

RIP Buddy

@sabastianlane8750 12 сағат бұрын

i have the same engine without all the upgrades and i got my kart to go 37 mph by just reaching back and pulling the throttle level

@nashguy207 10 ай бұрын

Nice upgrades for any go karts! How's Danny doing?

@BuildBreakRepeat 10 ай бұрын

He’s doing great, we might have him back on the channel soon….

@traviskeeton6313 5 ай бұрын

Me and my cousin are working on a gokart for him, it has the one wheel drive with a ungovern 5hp Flathead and runs almost 40

@gucciginge6053 9 ай бұрын

How does my stock predator 212 with gov delete reach 47? I’m very light so I guess that’s why

@Cal3b587 3 ай бұрын

You went 47 with no governor and the stock flywheel? Your lucky that thing didn't explode

@Olliepop-xi8kp 5 ай бұрын

i wonder how much it cost them in total to do all, got to be quite a lot right?

@paulpinto8400 7 ай бұрын

Rest peacefully Buddy.

@mikesbarn1858 10 ай бұрын

If you want to race it on an oval track you want a one wheel peel for cornering.

@igokarts4510 10 ай бұрын

❤️❤️❤️❤️

@laptopuser3323 10 ай бұрын

gday guys

@BuildBreakRepeat 10 ай бұрын

Howdy!

@NavardioGraham 2 ай бұрын

How much cc is she

@user-mz3lo5iv3h 4 ай бұрын

Brasil tá ligado

@parkerswaim6392 7 ай бұрын

Now you should 5.9 swap it

@SuperDave-xs6pt 2 ай бұрын

Next time upgrading, torque converter and disc brakes...

@matthouck1591 5 ай бұрын

I guess my question is, you put all that extra money into the stock 212. Why didn't you just buy a ghost an call it a day? Already comes with all that stuff you added

@same1eka 9 ай бұрын

3:09 he didn’t wash his hands

@larry-zs7kq 10 ай бұрын

rip buddy

@Cozcacuauhtli 2 ай бұрын

👍👍👍👍👶

@fredericklogue6566 10 ай бұрын

Sorry about Buddy. Put a real break on that cart at that speed.

@Youhaverights6 9 ай бұрын

Bye everyone Back to North Carolina!!!! LOL

@richardfife8192 2 ай бұрын

Needs a disk brake.

@bambr1861 10 ай бұрын

Как тебе такое Илон Маск?

@The_real_papadon 3 ай бұрын

Ah your doggy, I’m sorry😢

@Qauy684 7 ай бұрын

Can you sell it to me

@3JR272 7 ай бұрын

lifan gs212e

@rednecksdoitbetter491 5 ай бұрын

Sorry about buddy I just lost my best friend of 12 years

@warhound7781 10 ай бұрын

Had to add a massive weight to my old carts front end when it had the 433cc Yamaha sled engine on it as it didn't turn worth a darn without it. And ya it was insanely fast for mph 70+.