Building a 5.1 Surround Home Theater System 3D PRINTED

Building a 5.1 Surround Home Theater System 3D PRINTED - by SoundBlab

Рет қаралды 51,740

Жыл бұрын

JLCPCB 3D printing from $0.3, Get JLCPCB $54 new user coupon 3d.jlcpcb.com/?from=3D_CNC
JLCPCB PCB+PCBA from $2, Get JLCPCB $54 new user coupon jlcpcb.com/RPI
This is a completely 3D printed high quality 5.1 surround system, using drivers from Dayton Audio and Tang Band. Any capable AV Receiver will be able to drive this system, however you do not need very much amplifier power, which means that even a good budget AV receiver will be more than suitable. The subwoofer can easily go down to 35Hz, and will provide ample bass output for a small to medium sized room.
Get the BUILD PLAN here: bit.ly/3SilozG
Parts Lists:
- Artillery Sidewinder X2 3D Printer - bit.ly/3CN6Um4 , amzn.to/3exzUF4
- Creality 3D® Ender-3 V2 Neo 3D Printer - www.banggood.com/custlink/DK3... , (Amazon) amzn.to/3rZUD7u
- Speaker wire (14 AWG) - (US) parts-express.sjv.io/e4yRJz , (EU) bit.ly/39erRI4
- Tang Band W6-1139SIF 6-1/2" Paper Cone Subwoofer - (US) parts-express.sjv.io/LPADrM , (EU) bit.ly/3RfDlND
- Dayton Audio DMA58-8 2" Dual Magnet Aluminium Cone Full-Range Driver 8 Ohm - (US) parts-express.sjv.io/e4yRG6 , (EU) bit.ly/3r9U6PG
- Lepai LP210PA 2.1 Plate Amplifier with Power Supply - (US) parts-express.sjv.io/15nb36 , (EU) bit.ly/3BC5WXQ , bit.ly/3Rab6jA , (Amazon) amzn.to/3D0YIOV , amzn.to/3T7OZfl
- Speaker Binding Posts - (US) amzn.to/3BFct4b
- PLA Matte Filament 1.75mm 1Kg - (US) amzn.to/3C3nQEb , amzn.to/3dIXzSh
- #6 x 3/4" (3.3 x 19 mm) Deep Thread Pan Head Screws Black - (US) bit.ly/2Gvk8XM , (EU) bit.ly/3maZwqC
- Polyester Batting - amzn.to/3xAhj17
- 6mm x 3mm (1/4 inch wide, 1/8 inch thick) Self Adhesive Weather Stripping - amzn.to/3u1N0vF
- Custom PCBs - jlcpcb.com/?from=RPI
- 20mm or 3.4inch Stick-on felt feet - amzn.to/3feVCxg
- Rubber Stick-on feet - amzn.to/3dy5Vwd
- CA Glue - amzn.to/3DQkqGs
- Construction Adhesive or 2-Part Epoxy Glue - amzn.to/3C6faNE , amzn.to/3C3rE8p
- Drill - amzn.to/3fcZgIa , amzn.to/3Uz1W35
- Drill Bits - amzn.to/2hOSS8O
- Hot glue gun - amzn.to/3C3cr7r
- Screwdrivers - amzn.to/3Racm6i
- Orbital sander with 240 grit sandpaper - amzn.to/2zljy7Y , amzn.to/3LJhcGG
- Wire Snips - amzn.to/2zkGh44
- Soldering Iron and Solder - amzn.to/2yydWd2
- Utility Knife - amzn.to/3dHROEy
SUPPORT THE CHANNEL:
- SoundBlab Website and Build Plans - www.soundblab.net
- Patreon - / soundblab
- KZfaq Membership: / @soundblab
FOLLOW THE CHANNEL:
- KZfaq - goo.gl/EWMSXV
- Instagram: / soundblab
- Pinterest: / soundblab
- Twitter: / soundblabs
OTHER CHANNELS:
- Mixtape // Music for everyone and every occasion - bit.ly/3Cg3pUA
CHECK OUT MY AMAZON SHOP for recommended gear, tools, etc.:
- www.amazon.com/shop/soundblab
Audio Components & Solutions:
- Parts Express (US) - parts-express.sjv.io/yRNVk2
- Soundimports (EU) - bit.ly/3B0xWEn
- Axiomedia (EU) - bit.ly/3TUQUoA
Get Whole house audio via ARYLIC:
- www.arylic.com?aff=9
Music:
- www.epidemicsound.com/referra...

Пікірлер: 91

@SoundBlab Жыл бұрын

Get the BUILD PLAN here: bit.ly/3SilozG

@chakireladraoui9331 Жыл бұрын

Good my friend

@newbutthunt Жыл бұрын

BOSE is punching the air right now.

@WiLDCATZ Жыл бұрын

Bose is junk.

@AushiaCreative Жыл бұрын

Your diy speaker always perfect!! The design and output sound always amazing!

@SoundBlab Жыл бұрын

Thank you so much!

@rhunt2363 Жыл бұрын

Awesome work! Thank you for sharing this

@SoundBlab Жыл бұрын

Glad you enjoyed it!

@nunocampos1805 Жыл бұрын

Don’t know where to begin. My absolute favourite video of yours so far. The highlight has to be how you designed the speaker mounts to also help with cable routing. Really clever. Glad to see the days of needing tools and and know how in woodworking are over when it comes to build a quality small form factor speaker set. And the subwoofer is also amazing. It takes so little space you could probably have more than one and not have them call out attention. Painting them the same color as the walls also was great. You’ve left me dreaming of a 7.4.6 atmos setup this compact.

@SoundBlab Жыл бұрын

Thanks so much, glad you enjoyed the project. I am super happy with these and have been using them everyday ever since, and they sound great. You would think the plastic enclosures cannot possibly sound good, but when designed correctly, it has surprised me.

@gayathrahewamadduma8628 Жыл бұрын

This channel should be reach at least 10M subs ♥️♥️♥️

@chakireladraoui9331 Жыл бұрын

Good my friend I'm happy to watching your videos thank you

@SoundBlab Жыл бұрын

Thank you!

@LucasPfaff Жыл бұрын

3:20 in case you plan on printing a lot more, I'd totally recommend you a cheap deburring tool. It makes cleaning corners, chamfers and fillets just such a breeze and results look insanely good. I love your stuff, recently build the Dynamites and think about build its sub as well. The 3D printed set is also intriguing but I just dig the look of large fillets, haha

@SoundBlab Жыл бұрын

I definitely need one of those! Glad you like the builds. Keep going!

@Abelectronics.2003 Жыл бұрын

Thanks for making 5.1 home theatre

@SoundBlab Жыл бұрын

No problem

@theraghavs Жыл бұрын

That sound wow..

@SoundBlab Жыл бұрын

Thanks

@Thalluri-Rakesh Жыл бұрын

Great idea 💡

@SoundBlab Жыл бұрын

Thanks

@WildChinoise Жыл бұрын

Very nice!

@SoundBlab Жыл бұрын

Thanks

@cepcahyachanel Жыл бұрын

NICE JOB

@SoundBlab Жыл бұрын

Thanks

@karthikraj550 Жыл бұрын

Very nice 👍

@SoundBlab Жыл бұрын

Thanks!

@DavidSusiloUnscripted Жыл бұрын

I’m not a DIYer but this channel is great. Subscribed! PS: i personally like the texture of printed plastics so I personally would leave it as is (not smoothed) ❤

@SoundBlab Жыл бұрын

Thanks for the sub!

@Confusius. Жыл бұрын

I once printed a speaker too. Took ages to print and sounded like...plastic. Then I made a wooden one of the exact same dimensions et voilà, sounds like it should. And it took me a quarter of the time to finish. And don't forget the costs. The electricity alone used for printing costs way more than the plywood.

@liyoshiyona Жыл бұрын

Perfect ✌️

@SoundBlab Жыл бұрын

Thanks ✌️

@VioletGiraffe Жыл бұрын

I didn't expect your recording of the system to sound so good. Did you use your calibrated measuring mic to record the sound? I have decent headphones, and I'm impressed!

@SoundBlab Жыл бұрын

Thanks. Recording with a Zoom H1 at 24/96

@BackyardBoatworks Жыл бұрын

Hello. I found your channel today and I think I watched every video! Quick question…I’m planning an stereo upgrade in my bedroom/TV room which is rather small at 12feet wide and 10feet deep with the listening position in the bed 10 feet away from the TV wall. What type of speaker design would you use for a room like this? I can’t have large tower speakers on the floor as it’ll simply clog up the living space. I was thinking an extra large sound bar with left right and center built into the same bar would be the cleanest look for the room but I’m unsure if it’ll have the best sound quality. Thanks in advance.

@SoundBlab Жыл бұрын

A sound bar is a good option, if you get one that has decent sound. Some also come with a small subwoofer for bass, or some have limited bass response built in with passive radiators.

@salemrdwd8497 Жыл бұрын

nice enginering man

@SoundBlab Жыл бұрын

Thanks

@jackal6902 4 ай бұрын

All that.. I reckon I’ll just buy some. 😀

@user-js4rc4fo1g 10 ай бұрын

В первый раз вижу,что фазоинвертор сабвуфера,находиться сверху.Оригинально.

@p_mouse8676 Жыл бұрын

Nice made speakers! At 7:51 you're showing the impedance graph. I would double check your calibration, because the graph looks rather strange for the a LR bafflestep compensation. That should be just only be a straight line going upward.

@JordanKL1 Жыл бұрын

there's an 18k resonance from the driver

@p_mouse8676 Жыл бұрын

@@JordanKL1 a resonance would show as a peak in the impedance as well as being much narrower.

@JordanKL1 Жыл бұрын

Ahh yeah and the original response shows no peak. Looks like something in the filter is causing the large peak in response at 18k.

@tobiasprindal-nielsen1474 6 ай бұрын

Love the builds on your channel which is why i am subscribed. :) In this build how much filament should i assume to use in the process? 1. Subwoofer 2. Front, Center and surround Thx in advance

@SoundBlab 6 ай бұрын

You are looking at between 3 and 4 1kg spools for full 5.1 set at 20-30% infill.

@anandshah71 Жыл бұрын

Nice build for a medium to large can u make a larger sub or 2 drivers in sub to generate more pressure. I won’t mind using a powerful amp instead of lepai Also I see u r a TB fan. Would be great to see some peerless drivers used too

@SoundBlab Жыл бұрын

Thanks! You can even use two subs, but the one actually really does a good job and two might even be overkill.

@calieburger3113 Жыл бұрын

Awesome video. I just wish we could get the daytona speakers locally, parts express's shipping to SA is a bit crazy .

@SoundBlab Жыл бұрын

Thanks! These days, importing from Europe is less expensive. Try Soundimports or TLHP.

@calieburger3113 Жыл бұрын

@@SoundBlab thanks Mr soundblab

@Frambhueee Жыл бұрын

Very nice 3d printed speakers!, With that you can make something more stylish too, I have in mind create a subwoofer box with a shape of a turbine jet. Maybe you can build it if I gave you the idea that I have in mind

@CosminRotaru Жыл бұрын

Exactly my thoughts! What a wasted opportunity here to make some shapes that are very hard to make through other techniques. It does sounds good otherwise.

@SoundBlab Жыл бұрын

Thanks. I will attempt something a bit more complex in future. Its my 1st real try at 3D printing, so just working my way up to it. However, I prefer more practical, functional and natural aesthetic designs, not sure it will be a jet turbine. But thanks for the imspiration!

@SoundBlab Жыл бұрын

Thanks. The best opportunity is to just make something, and then take it from there. I wanted something very plain, so ot could fit into my lounge without attracting too much attention. Dont think more organic shapes would have worked here. But perhaps for another oroject in the future.

@CosminRotaru Жыл бұрын

@@SoundBlab speakers enclosures is no kids play and you've done an awesome job indeed. I was just thinking 3d printing offers some interesting opportunities. Looking forward to your new projects.

@SoundBlab Жыл бұрын

Thanks man, appreciated!

@prettyhard0150 Жыл бұрын

Hexabase has lots of vids making speaker box using 3d printers. You can learn or copy his style connecting or joining 3d printed parts.

@SoundBlab Жыл бұрын

Yeah, he does have some good examples of 3D printed enclosures.

@VioletGiraffe Жыл бұрын

Question: what about the interference pattern (comb filtering) between the two identical drivers?

@SoundBlab Жыл бұрын

Comb filtering at a typical distance when listening to speakers such as this is not a problem. It only really becomes a problem when you listen near-field. At a longer distance room reflections start to play a role and will potentially cause much more issues depending on your room. For this size driver, it should start only around 7KHz or so, but my measurements even at 1m did not show any unusual comb filtering in this case. Should you place the two drivers much further apart, only then will the difference in distance between the two drivers and your ears cause a phase cancellation since the sound from each will arrive at your ears at different times, but so close together, they act almost as one driver.

@VioletGiraffe Жыл бұрын

@@SoundBlab, thank you for the detailed explanation, I appreciate it.

@pomanprod Жыл бұрын

PLA sucks for subwoofers. I printed one from Hexibase and it rattled even with 50% infill. I tried PEG, just as bad. Back to good old Birch board. The 3D print is great for the vent tubes or intricates vents but not as a cabinet. I was thinking of printing with 10% infill then pump concrete in between the walls of the PLA cabinet but never got around to doing it.

@vinylcabasse Жыл бұрын

this one seems impressively braced - the 3 sections with thick bracing between, i'd imagine resonance would be far above the 150hz crossover point

@keatonjones6115 Жыл бұрын

ive got a hexibase one printed in pla with no rattles and a personal sub design with no rattles either, plus a set of speakers , its likely stringing in the walls or some wall not quite touching each other, try turning off 'avoid crossing outline' as this makes stringing occur in the infill, and turn wiping on as well as outline overlap to 35-40% . Ive had to reprint so many for similar issues but find these setting helped alot (i use simplify 3d but i think cura has similar settings) . But with the hexibase build it will make port noise if running above tuning frequency so keep that in mind also. If the sub in this video doesnt rattle, hexibase pla sub when he makes it doesnt rattle and mine doesnt i think its your print settings!

@jumpman255 11 ай бұрын

Would there be repercussions to sound quality if I was to do the exact same build with wood?

@SoundBlab 11 ай бұрын

No, as long as you keep the internal volumes the same, and the size and length of the port in the sub the same.

@hexyou5993 Жыл бұрын

Which program do you use for 3d design

@SoundBlab Жыл бұрын

For this build I used Onshape.

@anandshah71 Жыл бұрын

Can I use the 4ohm Dayton FRversion can’t get the 8 ohm in my country

@SoundBlab Жыл бұрын

Nope, only the 8 ohm version will work with the designed filter components.

@pedrotski Жыл бұрын

Tang Band really are little weapons

@SoundBlab Жыл бұрын

Jip sure are!

@robinprivat3024 Жыл бұрын

The dma 58 are 2 inch and not 2.5 inch right?

@SoundBlab Жыл бұрын

Yes, you are correct. My bad.

@eballacharles0302 Жыл бұрын

👊👍😲❤️

@TheManeliss Жыл бұрын

The only and big question: how have you calculate your enclosures?? From an other builder: You must test for medium and high frequencys a linear amplifier. Class D is only suitable for bass boxes. High freq are so agressive... I have a big experience with all TPA ics, if you want to exchange... For your big room a 8 inch is a better choice. Test your sub in your sleeping room... ;-) Great channel! Best from France!

@SoundBlab Жыл бұрын

I used WinISD to calculate enclosure sizes. The 6inch works rather well. An 8 inch would be better, but the 6 is more than able to keep up and produce enough bass. Thanks! Keep well!

@TheManeliss Жыл бұрын

@@SoundBlab WinISD is the best freeware. If what you listen to is enough with a 6 inch great good you do...

@TheManeliss Жыл бұрын

@@SoundBlab It's my pc software too. An internet adress in my language make the same and little different. I make a mix. My first was caad from monacor late 90's. I listen wide sort of music an i search best for all. For rock or pop a 6 is for me a great choice. I have build a 2.1 with the 5" tang band. It's totally crazy in a 18m2 room!! Have a nice day!!