No video
BUILDING A YAMAHA YFZ450r FROM THE GROUND UP - HOUSER XC A ARMS INSTALL
Рет қаралды 5,205
Күн бұрынwhat's up everyone
Time to get these a arms setup and installed
www.houser-rac...
THANKS FOR WATCHING!
www.epidemicso....
www.ebaystores....
www.epidemicso...
MY RIDES
2014 YAMAHA YFZ450R(PRACTICE QUAD)
2020 BLACKED OUT YAMAHA YFZ450R(SOLD)
2021 BLUED OUT YAMAHA YFZ450R (RAFFLED)
MY FILMING GEAR
5 GOPRO HERO 7's
2 HERO 9's
1 HERO 10
DJI MAVIC AIR 2
@jeffreyginn9643 2 жыл бұрын
Glad to see you’re finally building the second cleanest yfz😉
@ononewheel7 2 жыл бұрын
Ya my first blacked out one is still hard to beat 🤣🤣🤣
@jeffreyginn9643 2 жыл бұрын
@@ononewheel7 I hate you😂😂😂
@shaunbarber2746 2 жыл бұрын
Looking good, keep em coming......
@ononewheel7 2 жыл бұрын
Thanks man
@user-oi6ix1cv2n 2 жыл бұрын
👏👏👏👍👍
@dustinrichards8401 5 ай бұрын
For the houser tie rods do you have to reuse the jam nuts off the stock tie rods for the tie rod ends?
@ononewheel7 5 ай бұрын
Yes
@dustinrichards8401 5 ай бұрын
@@ononewheel7 ok, mine are pretty stuck on the stock ones so would you happen to know the thread pitch of the nuts
@ononewheel7 5 ай бұрын
Not sure you can order new ones from rockymountain
@dustinrichards8401 5 ай бұрын
Did you put nylon nuts on the ball joints to replace the castle nuts cause my ball joints don’t have the hole for a cotter pin and was told I could reuse the castle nut with some blue loctite but would feel more comfortable with a nylon nut
@ononewheel7 5 ай бұрын
I did so my two upper ball joints came with the nylon nuts so i just grabbed some for the lower ball joints.
@dustinrichards8401 5 ай бұрын
@@ononewheel7 ok thank you, long shot but would you happen to know what thread pitch the nuts would be
@ononewheel7 5 ай бұрын
I don’t sorry i think if i remember correctly its not metric i just brought it w me to the hardware store and matched it up.
@dustinrichards8401 5 ай бұрын
@@ononewheel7 ok, thank you again!
@probuiltatv5271 Жыл бұрын
Just installed houser mx a-arms, stock spindles, what castor setting you recommend to start with on the slicast?
@ononewheel7 Жыл бұрын
Nice man. I run my setup at -3 for the caster settings but that is recommended for xc. Not sure what mx is it may be more towards center or positive caster.
@wittracing72davidwitt74 2 жыл бұрын
My son just boke his OEM Subframe . I put a new OEM one on . Have you every run A Subframe Support ? I was looking a Force Racing Subframe Support
@ononewheel7 2 жыл бұрын
In 2020 i ran the xcel subframe it was awesome they stopped making them. LSR makes one but I’m not fond of the design and walsh makes one that is super expensive i have seen the braces it sure wont hurt.
@wittracing72davidwitt74 2 жыл бұрын
@@ononewheel7 Thanks for the info
@ononewheel7 2 жыл бұрын
Anytime man
@bigl2452 2 жыл бұрын
2020YFZ450rse...throttle cable recently became super slack from the box on the right side of the hand grips. How do I tighten this back up ?
@bigl2452 2 жыл бұрын
Do you have a video on this
@ononewheel7 2 жыл бұрын
There is an adjustment at the throttle body and at the lever check both and adjust as needed.
@derekhaynes4251 2 жыл бұрын
What subframe are you going to put on it?
@ononewheel7 2 жыл бұрын
Oem subframe
@justride9199 2 жыл бұрын
How’d you learn how to do all this ??
@kylebeach2316 2 жыл бұрын
It's not hard at all do if you don't know how to do things just watch a KZfaq video on what you want
@ononewheel7 2 жыл бұрын
Learned by just doing it grab a manual for any quad and its all in there.
@redrockracing4571 Жыл бұрын
Hey ononewheel7 do you have any knowledge of the Teixeira Tech A-arms? I like the ground clearance.
@ononewheel7 Жыл бұрын
I have some on my can am. Just uppers but they are very nice and beefy i have always heard good thing on his products.
@redrockracing4571 Жыл бұрын
@@ononewheel7 Thanks man I’m build up my 22 YFZ in XC
@ononewheel7 Жыл бұрын
@@redrockracing4571 nice anytime
@redrockracing4571 Жыл бұрын
@@ononewheel7 You use LTR Geometry Housers right? Have you noticed any difference from Yamahas though?
@ononewheel7 Жыл бұрын
What kind of difference?
@seanyc3734 2 жыл бұрын
Hey man are you from PA? I would love to get a ride in sometime
@ononewheel7 2 жыл бұрын
Rhode island.
@seanyc3734 2 жыл бұрын
@@ononewheel7 if you are ever doing a subscriber ride let me know! I would for sure make the trip up there. Or if you are ever in eastern PA let me know I have some great spots in coal county
@bigl2452 Жыл бұрын
Hello sir,I've been informed that my 2020 YFZ450rse issue was not the throttle cable it's the spring inside the throttle body. My issue is, I'm told that I can't replace the spring, I'm told I must replace the entire throttle body. Is this true?
@ononewheel7 Жыл бұрын
You can absolutely replace the throttle body spring. Who ever is telling you this is trying to screw you. Its super easy to replace.
@bigl2452 Жыл бұрын
Just so I'm clear, we are talking about the throttle body near the air intake.. not the throttle button on the handle bars.. correct..( sorry for the crazy questions, I'm not as knowledgeable as you, I like to be totally clear)
@ononewheel7 Жыл бұрын
Yup you can change that yourself its easy.
@xclife211 2 жыл бұрын
How did you hurt yourself is that why you haven't done nyoa
@ononewheel7 2 жыл бұрын
I made the decision not to run for points this year before the season started i had planned to race a couple NYOA’s i went to greek peak and got hurt riding downhill on Saturday 😩
@xclife211 2 жыл бұрын
@@ononewheel7 bummer about the fall hope all goes well next year I've been having electronics issues this year and chasing electrical issues is horrible
@ononewheel7 2 жыл бұрын
Efi machines can be a nightmare thats for sure. What is your issue?
@xclife211 2 жыл бұрын
@@ononewheel7 I had a grounded short from a rubbed wire and now I'm waiting on a new tps to come in so hopefully I can get to twisted fence lol
@ononewheel7 2 жыл бұрын
@@xclife211 bummer man hope you get her fixd up in time 🙏
ATVonDemand
Рет қаралды 6 М.
Tyler McNabb
Рет қаралды 2,2 М.