Building my 1.9TTDI bottom end for 400++hp
Рет қаралды 9,122
2 жыл бұрынI build the bottom end of my 1.9tdi engine, daily 400+hp build.
Get Dragy here:
dragymotorsports.com/?rfsn=63...
Use code BROLYFE10 for Discount
Song: Koven - Looking For More [NCS10 Release]
Music provided by NoCopyrightSounds
Free Download/Stream: NCS.io/LookingForMore
Watch: • Koven - Looking For Mo...
Song: Chris Later & Dany Yeager - There's Nobody Else [NCS Release]
Music provided by NoCopyrightSounds
Free Download/Stream: NCS.io/TheresNobodyElse
Watch: • Chris Later & Dany Yea...
Song: Poylow - Got Me (feat. Nito-Onna) [NCS Release]Music provided by NoCopyrightSoundsFree Download/Stream: NCS.io/GotMeWatch: • Poylow - Got Me (feat....
@brolyfe8018 2 жыл бұрын
Subscribe for more content and Check out our Bio for your discount on Dragy! Code: BROLYFE10
@jamesk0141 Жыл бұрын
Didn't realise yeah had a build videos up lad. Good watch so far all the better she's in a b7 😅
@brolyfe8018 Жыл бұрын
Haha cheers man, new builds coming soon and quality improvements too 😂 she was in a b6 and I believe she's going into another b6!
@lukeodonnell2974 Жыл бұрын
rebuilding a BLS at the moment piston 1 had a break on top compression ring. Worked on cars for a long time only thing im worried about is the sputter bearings as can't find any info on where they sit and what one goes to the top of conrod and what one goes toward bottom, one has a copper layer the other is normal looking im sure copper layer goes towards top of con?
@brolyfe8018 Жыл бұрын
Copper layer is from wear, you'll need to get new bearings! Replace them on all conrods with new bolts. BLS tend to wear these and spin them destroying crank and sometimes engine!
@lukeodonnell2974 Жыл бұрын
@@brolyfe8018 thanks for letting me know, I knew the stretch bolts had to go but no idea the copper stuff was actually worn as its worn perfectly even, on the ball
@brolyfe8018 Жыл бұрын
No problem happy to help
@stefanobattistino2441 4 ай бұрын
La frizione resiste?
@brolyfe8018 4 ай бұрын
Sachs SRE pressure plate and Paddle clutch plate from precision clutch components, it worked no problem
@manuelstouy8148 4 ай бұрын
why do you drill out the pistons?
@brolyfe8018 4 ай бұрын
Drilling out the pistons is to reduce compression ratio and to stop them melting! Have melted a few standard pistons!
@manuelstouy8148 4 ай бұрын
and then you can drive the standard pistons? up to what performance? Thanks my friend for the information! @@brolyfe8018
@brolyfe8018 4 ай бұрын
You can make over 400hp with them! No problem!
@manuelstouy8148 4 ай бұрын
@@brolyfe8018 thank you!
@hksjoshua 4 ай бұрын
Use water methanol injection bruh.
@madalinbandoiu1509 Жыл бұрын
AVF ?
@brolyfe8018 Жыл бұрын
Of course 👌
Francisco J Suárez
Рет қаралды 169 М.
Macolaiden
Рет қаралды 21 М.
David Shoemaker
Рет қаралды 13 М.
I Do Cars
Рет қаралды 238 М.
Austin Niemela
Рет қаралды 77 М.
Я тебя застрелю🤬 #эндуро #эндурокросс #мотоцикл #мото #кросс #прохват #moto #motocycle #enduro #cros
Денис Сумкин Enduro
Рет қаралды 8 МЛН
Мотомалышка Алина
Рет қаралды 6 МЛН