Buying and fixing a stump grinder part 2/2 (Bandit SG-40).

No video

Buying and fixing a stump grinder part 2/2 (Bandit SG-40).

Рет қаралды 2,446

Күн бұрын

00:14 remove PTO clutch and engine
04:28 disassemble engine
08:32 weld up block
10:37 clean aluminum off crank
13:20 reinstall crankshaft/assemble engine
16:54 check crank end play
18:34 test run engine
20:43 disassemble belt drive/jackshaft
23:22 remove cutter wheel frame
24:51 explain problem with worn frame
26:34 explain solution
27:22 bore out frame
36:30 press in new trunnion tube
37:33 reassemble cutter wheel frame
41:22 explain minor belt issues
43:53 test grind
53:18 outro

Пікірлер: 43

@chrislindquist2003 2 ай бұрын

Nice job with that repair bub. Most guys wouldn't even attempt to fix that block. I'm impressed 👍. Really enjoy your videos. Keep them coming!

@AlwaysBored123 2 ай бұрын

Thanks a lot man.

@ThePurpleSquirrel 2 ай бұрын

You have the patience of Job and the wisdom of Solomon.

@jackschwink 2 ай бұрын

Very good job welding the hole in the block! I definitely don’t trust my welding skills enough to do that 😂

@AlwaysBored123 2 ай бұрын

Thanks. Aluminum can be a real pain to weld but that actually went better than I expected.

@ianmoone2359 2 ай бұрын

Different belt companies measure their belts differently. Some denote inside radius while others denote outside radius. Two different brand belts with the same designation can be either slightly longer or shorter depending on the belt manufacturers method of measurement. There’s not one standard across all manufacturers. Impressed by your abilities for a young buck. Line boring on your mill was very clever indeed. Keep up the good work.

@AlwaysBored123 2 ай бұрын

I think these were both measured the same but I'm not positive. It's working for now I'll try a factory belt next time. Thanks for the comment.

@Anders_HeymSR30 2 ай бұрын

No pun intended, but blown away by your mechanical skills!

@AlwaysBored123 2 ай бұрын

Thanks a lot!

@jtaulen 2 ай бұрын

Thats a lot of effort and time into that machine at this stage ! Very impressive.

@jprich7 2 ай бұрын

Great video. Please keep them coming

@AlwaysBored123 2 ай бұрын

Thanks, will do!

@IHcubcadet 2 ай бұрын

Great job man. My Dad had a bridge port milling machine, it’s amazing how much stuff you can fix with one.

@AlwaysBored123 2 ай бұрын

They're nice to have for sure.

@whitby910 2 ай бұрын

A great video(s), thanks. Everything can be fixed in your world, impressive.

@AlwaysBored123 2 ай бұрын

Thanks I try lol.

@jzlharvey 2 ай бұрын

Wow. Top job!

@adman6380 2 ай бұрын

Amazing work as always

@adriannicholson8819 2 ай бұрын

It was Clever💡

@barthanes1 2 ай бұрын

Wow, it sounds great.

@TheHomePros6221 2 ай бұрын

One of my favorite channels!🙂

@gunbreon9309 2 ай бұрын

Woah amazingly done

@AlwaysBored123 2 ай бұрын

Thanks!

@IrenESorius 2 ай бұрын

Winner,, 👍‍‍🌟👍‍‍

@duotronic6451 2 ай бұрын

Impressive. ❤❤❤

@AlwaysBored123 2 ай бұрын

Thank you!

@silverclaw4 2 ай бұрын

7:18 ahh yes the classic snap ring goes flying never to be seen again.

@AlwaysBored123 2 ай бұрын

Lol it never fails.

@RustyInventions-wz6ir 2 ай бұрын

Just found your channel and subscribed. Very nice work

@AlwaysBored123 2 ай бұрын

Thanks!

@barthanes1 2 ай бұрын

Nice work. I thought you would need a donor crankcase and block.

@AlwaysBored123 2 ай бұрын

Thankfully not that would have been much more work.

@earlleelethbridge566 18 күн бұрын

Nice vid. I believe your excavator could of done a better job and flattened that mound. Hope you make money selling it. Still great skills to bring back to life.😎

@user-bq4lb4ug4c 2 ай бұрын

Great job bringing that machine back to life, most folks would have considered it to be totaled between the engine and the damaged shaft bore. You going to keep both stump grinders?

@AlwaysBored123 2 ай бұрын

Thanks. I definitely intend to sell one of them but I'm not sure which one I like better yet.

@Northsidestumpgrinding 2 ай бұрын

So we seen that the rod had fused to the crank. That’s the effect, what caused the failure? How many hours on the engine at the time of failure?

@AlwaysBored123 2 ай бұрын

I can't say for certain but I'm pretty sure this machine was rolled over based on the high center of gravity and all the broken parts on top of the engine. As far as I can tell it doesn't have a low oil shutoff so I think it was rolled and starved for oil before it could be shut down. It's showing 738 hours on the meter.

@TheHomePros6221 2 ай бұрын

Which one do you like the best? The bandit or the other one?

@AlwaysBored123 2 ай бұрын

I think I like the Barreto more but I need to use them both a little more before I can say for sure.

@barthanes1 2 ай бұрын

It's probably better to wear long sleeves when working with strong acids.

@AlwaysBored123 2 ай бұрын

That acid isn't very strong. You can spill it on bare skin and not feel anything for a few minutes so there's plenty of time to wash it off.