00:51 🚗 Primered surfaces can cause adhesion issues: Primed bumpers can develop primer dust in deep recessed areas, making the surface less adhesive. 03:01 🧼 Use a 50/50 overlap for better adhesion: Overlapping the wrap material by 50/50 helps improve adhesion, making it stick better, especially in areas where primer dust is present. 04:39 🧽 Surface preparation is crucial: Washing, using wax and grease remover, and clay barring the bumper surface can raise surface energy and improve wrap adhesion. 05:20 🛠 Warranty concerns: Wrapping over non-OEM paint or primered surfaces may void warranties, so it's essential to use proper techniques to ensure customer satisfaction. 00:02 📺 Educational content: The video provides useful tips and tricks for those wrapping bumpers, emphasizing the importance of surface preparation for a successful wrap job.

Literally the title of this video was my question that i googled and the video itself answered exactly to my question, so thank you!

Hello, I’m in the Primer Dust situation and appreciate your advice. Your post is older and I hope you have found better solutions to share? My car in epoxy primer and then urethane primer. I’ve wet sanded to 800 and cleaned with Dawn soap and 50/50 mix of isopropyl alcohol and water. Unfortunately still dust when I pull up vinyl like you did. Sticks good but worried when Wrap Installer has to reposition and then lose adhesion. Appreciate any new advice, thanks for your time.

I use laundry soap for all of my degreasing needs. It works great and I have never had any issues! Great vid!

Easy not to get primer dust if you properly sand and clay the primed piece before doing this.

When painting premiered parts we would use a red/grey scuff pad to give it some texture so the paint would bite . I would imagine if you used a grey fine pad and cleaned it properly it would get rid of that grey dust that comes off

Wet sanding all primer parts will get rid of uneven surface and dust that primer leaves behind then clean with soap and water.

Dope video and great tips! What do you do to minimize rock chips in front bumpers before wrapping on slightly older vehicles?

thank you for answering my qu about primer paint.

be careful out there my brother-in-law got hooked on primer dust!

Just finish sanding the bumper with atleast 3000 grit DA with an interface pad, wipe down with adhesive remover, and wax and grease remover

Great explanation and demonstration. I’ll be throwing some paint on my car before wrapping it. Thank you.

You never let it cool down properly & then take it off..and the primer surface is not prepped, because if grey comes off with it, the area should be tack-ragged and possibly need a real light sand before tack ragged..

Great example of vinyl to primed paint! Off topic, better to wrap a bumber ON or OFF a vehicle? I'm considering taking mine off for convenience, but worried about it flexing and moving while applying the wrap.

Tack is commonly use to lift debris off surfaces before applying paint should work

What if shows a lil bondo would it still stick even doe surface flat ???? Just askin for advice

sounds like you just justv rattle cansome rustoleum and 2x clear on your primer panels just to have a good mating surfaces, should be cheap enough and can look like shit because hey, you're wrapping it

Guys help me out so if I bondo my car for a little dent should I add some primer or just wrap over the bondo ?!?!?!

I guess polishing is a good idea. 👍🏼

Just watched ur video man. I have a question. Would “painting” over the primer help? What about clear coating over the primer? I have a bare polyurethane lip that. I have to wrap and am trying to figure out how i should prep it.

What about asking the painter to do a finish coat with epoxy primer/sealer? Another idea is scotch brite it with a grey pad which is 800 grit..

Maybe try a tack cloth 👍🏼 good luck!

If i take my car to get wrapped. Do they charge more if i wanna get a wrap on a unpainted part instead of a pre painted part

I have a unprime black bumper and wrap keeps peeling off , what can I apply

Wow. This was incredibly helpful to me.

Have you tried clay bar or detergents to remove primer dust before wrap?

How about a quick sand b4 wrap?

When do you use the underwater wrap

You got a update on what works the best a year later?

Hey man when it comes to textured plastic (2017 Jeep grand Cherokee limited exterior) , after sanding what would be the best way to bond 3m 1080 ? Should I use 94 or should I used adhesion promoter, paint & wrap ?

Try acetone for a final wipe

2000-3000; grit sandpaper?

Did you use a tck cloth

so it is possible but its basically temperary

Can I do sanding before vinyl wrap?

Please invest in a wireless mic, hard to hear ya and the size of the room you were in your voice was booming around...

Gets more tacky after the first time you peel it off. The solution: wrap it twice😂

Its primer

Get a wireless mic.

Very very poor sound

proper prep..wet sand..and acetone..then you wouldn't need a video