How to make Cornhole Boards // With 2 bonus features

No video

How to make Cornhole Boards // With 2 bonus features - Plans available!

Рет қаралды 75,458

Jesse does DIY

Күн бұрын

Пікірлер: 95

@ProTechEpoxyFloors 7 ай бұрын

I like the 2 embellishments, drink holders and bag storage is a nice touch

@JessedoesDIY 7 ай бұрын

For sure! Glad you like them

@greatgrandpaswoodworking Жыл бұрын

Looking good. I would suggest when trying to drill the hole put the drill in reverse to make the circle mark first then put it back to forward and drill. This will help stop the hole saw from traveling.

@JessedoesDIY Жыл бұрын

I'll have to try that!

@PatrickKelly-yo1ej 11 ай бұрын

Much better detail than the other videos similar to this. I like this design.

@JessedoesDIY 11 ай бұрын

Thanks very much!

@specialmustard237 18 күн бұрын

Awesome work! I’d say my two cents on your spacer/clamp/drink holder complication you asked for, would be to use a longer clamp going from leg to leg, lightly pinching the drink holder board between the legs. Tight enough where it won’t move around on you, and loose enough that you can gently tap it with a mallet to make fine adjustments until you’re ready to drive in the screws. I’m definitely going to try this! I’m thinking about adding a pop out “roof” above the drinks to keep bags from sliding off the back and knocking into drinks. Keep on trucking brother!

@JessedoesDIY 15 сағат бұрын

Thanks! I'm guessing I already spoke to you on Etsy at this point lol That's a great idea with the clamp. I haven't had anything slide into a drink yet, but I guess there is always a first time for everything. Will do man, you too!

@larryfox9290 8 ай бұрын

I just done a set with cup holder and I kept the legs bolted to the boards and measured down an 1.5” on both sides of the leg and drew a line then line the board up on the line. Then I used a clamp the hold the board in between the legs. Not saying that’s easier but that’s how I did it. Nice job on the boards.

@JessedoesDIY 8 ай бұрын

Awesome! Good to hear other methods, interesting to see how others do it. Hope you enjoy them!

@tonycovarrubias2707 4 ай бұрын

Love it thanks for your upgrade these type looks strong and effecient.

@JessedoesDIY 4 ай бұрын

Awesome, glad you like them. I tried to balance style and strength without making the weigh a ton.

@sadielouwho5795 Жыл бұрын

Very nice! You are very talented and funny too. 😂

@JessedoesDIY Жыл бұрын

Thanks very much!

@gurthbroox 2 ай бұрын

When I heard, “6 inch hole”, I subscribed.

@JessedoesDIY Ай бұрын

Nice...

@RefugeWoodcrafts Ай бұрын

I think you should adjust the drill chuck to prevent the drill kicking back when drilling the 6 inch hole.

@JessedoesDIY Ай бұрын

Thought about it , but I went for max force...and we all saw how that went.

@carolinepaltz324 11 ай бұрын

Very nice, I love your upgrades!

@JessedoesDIY 11 ай бұрын

Thanks very much!

@zebduffey5698 4 ай бұрын

My CNC Machine saves alot of these headaches. Onefinity fit the win

@drummer5437 2 ай бұрын

Great video, great job

@JessedoesDIY Ай бұрын

Appreciate it

@dubCanuck1 11 ай бұрын

Tip: grab the battery end with your off hand to not rip your arm off with big hole saws.

@JessedoesDIY 11 ай бұрын

I should have just put the handle on the drill to be honest, but I'll have to try that next time

@cirioli3 11 ай бұрын

Thanks! Would love the plans.

@JessedoesDIY 11 ай бұрын

Awesome! I'll start working on them tomorrow

@larryfleming8678 Жыл бұрын

sweet , nice job ...... thanks for the info....

@JessedoesDIY Жыл бұрын

Thanks!

@AnArmyOfFatGuys26 3 ай бұрын

Absolutely fantastic job brother. I can't wait to build me a pair just like this.

@JessedoesDIY Ай бұрын

Thanks man! Absolutely, have fun

@wwfd25chief 2 ай бұрын

If your drill came with a handle put that baby one before you use thar 6” hole saw. So much easier!!!

@JessedoesDIY 2 ай бұрын

Absolutely! I just...couldn't find mine lol

@samuelshaver4555 10 ай бұрын

Nice upgrades

@JessedoesDIY 10 ай бұрын

Thanks!

@thehobbyfanatic4610 2 ай бұрын

Great work man!

@tomchapin8406 8 ай бұрын

Just purchased your plans from ETSY and they look good. Going to make 4 sets for Xmas presents (one for myself!). Haven't looked closely at the video, but the materials list is missing the size of the pocket screws needed for the project. Thanks!

@JessedoesDIY 8 ай бұрын

Thanks very much! I'm sure everybody will enjoy them very much! Good luck on them all. Oh crap, you're right! I'll update it right now and can email you a new set

@tomchapin4327 8 ай бұрын

@@JessedoesDIY Thanks. My wife and I have really enjoyed this project. Grateful for you paving the way with your great plans!

@keithfowler632 9 ай бұрын

Looks good but acl regulation frames I believe are made from 1x3 limber not 1x4s

@JessedoesDIY 9 ай бұрын

Thanks. Regulation height is between 3.5"-4" to the top of the board when laying flat. The 1x4 is 3.5" tall and 1/2" plywood on top makes it a smidgen under 4". The whole board is regulation adult specs

@user-rq1dk6tz6t 2 ай бұрын

I bought the plan but have problems with the dimensions because my English is terrible :-( I really like the design and have learned to love the game and would like to build it

@JessedoesDIY 2 ай бұрын

It is a fun game. Can you use Google or Edge translate? Both browsers should be able to do it right in the plans

@toninhoalvim 4 ай бұрын

Boa tarde. Sou do brasil e gostaria de saber as dimensões da mesa do jogo e das bags. Vou fazer para divertir com a família e amigos.

@droidian 8 ай бұрын

Very nice. Now do a vid on the "Hoosier" version from the Midwest with just 2x4's and plywood. kek. I luv the cornbag holder(mice ate out mine in the garage), but the placement of the beer holders is bad because of the bags falling over the end. How has that worked for you? I won a set from Keystone Light($205.00) and gave it to my kid which is similar to the one you made.

@stevenserna2680 8 ай бұрын

I didn’t even think about the bags hitting the drinks in the holders. Perhaps adding a brace higher up on the legs would prevent the bags from reaching the drinks, or at least hitting them with full force. Thanks for pointing that out!

@JessedoesDIY 8 ай бұрын

Thanks. We'll I'm from Canada so that'll take a Google search because I have no idea what those are lol. Actually that's why the drink holder is tucked up nice and tight to it and not further out. Typically the bags go flying off the end and I haven't had an issue yet.

@scottdemonte3103 Ай бұрын

Very nice all around. D0 you have plans to link to?

@JessedoesDIY Ай бұрын

Thanks. In the description, I can't add links here. Or go to Etsy and search my channel name

@-cw8ht 3 ай бұрын

I just wish I could order some from him instead of building it ..came out great

@JessedoesDIY Ай бұрын

Thank you. But I don't have the time lol You can do it

@stradicfanatic 5 ай бұрын

love it! What brand is the water-based exterior clear coat?

@JessedoesDIY 5 ай бұрын

Thanks. I use Varathane Diamond, it may also be Rustoleum not Varathane depending where you are

@masonschneider9625 Ай бұрын

I don't mean to be "that guy" but are you sure that's 1/2" plywood. Looks like 3/4". But if it is, do you find it's enough thickness? I've read 1/2" can have a bit of a bounce to it when you throw the bag

@JessedoesDIY Ай бұрын

It's 100% 1/2". With the center braces I added there is no bounce at all, it's solid. I was worried about the same thing that's why I made the bag holder also support the top from below.

@masonschneider9625 Ай бұрын

Just finished building these this past weekend. Great video! My issue has always been folding legs. I just can't get them perfect. Each one seems to differ slightly from the next one, and it's single handedly my least favourite part of projects ... Anyways, from one Canadian to another, it's nice to see videos with Canadian references (and prices!). You have my subscription! GO OILERS

@vincentdangelo8024 9 ай бұрын

Could you attach the drink holder with the legs attached to the frame?

@JessedoesDIY 9 ай бұрын

It was harder to balance everything that way and not have it in the way, but if you can find a way, no real reason you can't

@bradgiroux9428 Ай бұрын

Where are the plans?

@JessedoesDIY Ай бұрын

In the description

@bradgiroux9428 Ай бұрын

@@JessedoesDIY thanks didn't see them

@katelaudie8188 Ай бұрын

What length of pocket hole screws did you use?

@JessedoesDIY Ай бұрын

Whatever your pocket jig says for 3/4" and 1/2" material, they are different

@markplehinger9055 3 ай бұрын

What are the depth of first pocket holes

@JessedoesDIY Ай бұрын

Whatever depth my jig goes to for 1/2" and 3/4" materials

@5309backbeat 4 ай бұрын

Did you use painter tape or frog tape when staining?

@JessedoesDIY 4 ай бұрын

Frog tape is painters tape, it's just branded is all. I just used basic ol scotch painters tape. I personally haven't been blown away by frog tape, especially given the price they charge. If you press regular painters tape down and into the project or a corner along the edge like you should normally, there basically is no difference, at least to me

@jasonsecaur7019 2 ай бұрын

d be great

@JessedoesDIY Ай бұрын

Thanks

@ArturVoskanyan24 6 ай бұрын

Hi.Thanks for video. How much kg the board? And what is the name of device in 1:51

@JessedoesDIY 6 ай бұрын

Anytime, glad you liked it. Per board...probably around 4 kgs if I had to guess. That's a pocket hole jig, Kreg is the brand.

@coreychristenson6500 2 ай бұрын

What kind of sprayer did u use?

@JessedoesDIY 2 ай бұрын

Wagner Flexio

@jkdmmabox 11 ай бұрын

How much would you say you ended up spending in materials? Thanks!

@JessedoesDIY 11 ай бұрын

It all depends on your area but around $110. Could be done cheaper with less expensive wood

@christianmitchell5384 4 ай бұрын

How long did you cut the legs originally?

@JessedoesDIY 4 ай бұрын

14" I think

@CWBush73 3 ай бұрын

What kind of table are u working on?

@JessedoesDIY Ай бұрын

Just a piece of 3/4" OSB on sawhorses

@sawyerhattersley3397 2 ай бұрын

What were the screws ?

@JessedoesDIY Ай бұрын

The pocket screws for assembly or the black carriage bolts?

@amberflores24 14 күн бұрын

how much to build that?

@JessedoesDIY 15 сағат бұрын

Maybe $100 for the pair, depends on your local pricing

@Alphasig336 3 ай бұрын

Go backwards with drill

@OdraMH 11 ай бұрын

This is not the video I was expecting it to be.

@JessedoesDIY 11 ай бұрын

What were you expecting?

@OdraMH 11 ай бұрын

@@JessedoesDIY A diy corn stripper that is not flimsy like those cheap gadgets sold in stores, the thumbnail gave me the impression of putting the cob in the hole, pushing, and the kernels would get stripped.

@JessedoesDIY 11 ай бұрын

Oh...nope. Cornhole is a yard game

@zachritchie7493 6 ай бұрын

Awesome! Want to send me the plans?!

@JessedoesDIY 5 ай бұрын

Thanks. Plans are in my Etsy store, link in the description

@mattybo29 3 ай бұрын

Those drink holders need to go. Not a good spot for that. I don't want beer on my bags

@thirstee1 2 ай бұрын

Don't hate, appreciate. Move them further apart, closer to the legs. I've had no interference with the bags spilling my brews. In fact even a tall bottle can't be tipped over this way.

@JessedoesDIY Ай бұрын

Thank you. I haven't had an issue either

@timkinney9690 Ай бұрын

Personal preference whether you include them or nought, nice option though.