Carpenters Usually Learn This Skill Last
Рет қаралды 156,454
Күн бұрынHead to www.squarespace.com/scottbrow... to save 10% off your first purchase of a website or domain.
Contribute here if you would like to support the channel - www.paypal.com/ncp/payment/FY...
Kenny made the door jig, and you can buy it here littleredken.store/
His insta / littleredken
Jess’s awesome overalls www.flouncygardenwear.co.nz/
MUSIC by Xpanda / xpandaprod
Support us on Patreon - www.patreon.com/user?u=16545763
0:00 Intro
0:31 Door stand
1:19 Where do you put the hinges?
1:51 Check the edge of your door first!
3:25 Mark out the hinges
4:33 Watch this if you have a hollow-core door
5:09 Cutting out the hinges
7:26 Marking the hinge screw holes
8:57 Check the door opening
9:32 Height of door jambs
11:28 Which side does the hinge go on the jamb?
11:56 Cutting the hinges again
12:53 Assembling the door frame
13:27 Packing the Hinge side first
14:15 Fixing the jambs to the frame
14:39 Fitting the door
15:11 Getting the gap right
16:41 Completing the door
17:22 Door stops
17:54 Wow, the big reveal
18:08 There is an easier way
18:54 Where did Jess get her overalls from?
The below are affiliate links. I get a small percentage when you buy using these links. It does not cost you anything extra, but helps supports the channel. Thanks!
My Tools
Tool belt amzn.to/3dXMZnk
Tool belt shoulder straps amzn.to/3AI0VLU
My favourite track saw amzn.to/3zE9usw
My framing nailer amzn.to/3DvCd3W
Hammer with wooden handle amzn.to/3jRhQ92
Rubber grip for hammer amzn.to/3jTM7UE
Knipex nail puller amzn.to/3DVER47
Long level amzn.to/3WvwmnF
Nail puller amzn.to/3WsMGWb
Multi-tool amzn.to/3WjUPwa
Speed Square amzn.to/3yAaE5f
Small laser measure amzn.to/3Nu4goI
My craft knife amzn.to/3T0TEPs
Mini pocket saw amzn.to/3NsVjMF
Little bar for little nails amzn.to/3fs6vwu
Big bar for big nails amzn.to/3Nx9OPs
Makita Circular Saw amzn.to/3qYzaKH
Battery holders Makita 18v amzn.to/3Ws2Krf
Battery holders Makita 40v amzn.to/3U0TdpF
Awesome ratchet clamp amzn.to/3dSGa6s
Impact driver (main drill) amzn.to/3xDmBat
Other drill for pilot holes amzn.to/3yAYjh4
My Table Saw amzn.to/2UzuOxp
My favourite vacuum (newer version) amzn.to/3yxss0S
Full face mask amzn.to/3hH4Cce
Ear muffs amzn.to/3yNAWBl
Green line laser level amzn.to/3yqYdJ0
Vaccuum suction lifter amzn.to/3U1oaKt
The Camera Gear I use
Main Camera amzn.to/3AD2if5
Backup Camera amzn.to/3jTGTbv
Main Lens (main camera) amzn.to/3wp0hzU
Lens for Backup Camera amzn.to/3jWaFfU
Microphone amzn.to/36pNWAA
Tripod amzn.to/3yxSeCb
Headphones amzn.to/3xqm2R4
Drone amzn.to/3xp9OrO
My coffee stuff
Fancy coffee kettle amzn.to/3fpbyhe
Fancy bean grinder amzn.to/3SZiZcn
For keeping my coffee fresh amzn.to/3NxRzt7
For weighing the coffee amzn.to/3FLcJCp
Aeropress (Coffee) amzn.to/3ijpvdQ
My Work Wear
Work Pants euroworkweardirect.com.au/col...
Vest euroworkweardirect.com.au/pro...
Kneepads euroworkweardirect.com.au/col...
Belt euroworkweardirect.com.au/col...
SEND STUFF HERE
PO BOX 3506
Richmond 7050
New Zealand
Disclaimer:
These videos are intended to provide information and inspiration only. If you choose to imitate, duplicate or copy anything you may have observed in these videos, you do so at your own risk. Scott Brown Carpentry Ltd does not take any responsibility for any action taken as a result of the information or advice on this KZfaq channel and shall not have any liability in respect of any injury or damage that may result.
To view full disclaimer, click here: www.scottbrowncarpentry.com/d...
@EUC-lid 2 ай бұрын
The greatest thing about Jess episodes is never knowing when or where the Squarespace ad will come from. It’s the psychological thriller element of this channel that makes Fridays worth getting out of bed for.
@hw2508 2 ай бұрын
THAT's the best thing for you? I think Jess is the highlight in itself.
@patbird9694 2 ай бұрын
You might need to evaluate your life.
@sam-bn5hl 2 ай бұрын
hahahahahah thats so true man! Greatings from the Netherlands!!!
@PabloEskimofo 2 ай бұрын
18:44 “you can buy pre-hung doors” Jess: “WHAT?!” 😂
@TpetPlayr 2 ай бұрын
The PERFECT Ending. hahahaha
@mouseripper4257 2 ай бұрын
Laughed till I cried! 😂
@cernunnoskali 2 ай бұрын
Some door hanging tips that I find useful -1: use wooden wedges instead of plastic packers, I'll cut long 3 degree wedges when I have some spare time, cut up tubs of them. Have the wedges facing in opposite directions, creates flat packers that are adjustable in thickness. Fixing nail underneath wedges, so you can tap them past each other to plumb door and adjust door to jamb gaps. Much faster than using plastic window packers. 2: Cut head the same size as the frame opening, level up the position of the hinge jamb. Cut a rebate 5mm deep by the jamb thickness into the head. Measure door width + 7mm ( standard door thickness), then rebate 5mm deep for latch jamb. Doesn't take very long to do the rebates but makes for a much stronger door set up. 3. When the hinge jamb is set in, 90 degrees to the wall ( easy with opposing wedges) have a piece of board/timber the same size as your door opening . Then just place it at the bottom of the two jambs, wedge the latch jamb tight to the spacing board. This will make sure the latch jamb and hinge jamb are 90 degrees to the wall. 4: Single hinge templates are useful but what is better is making a hinge template with all three hinges on it. 12mm MDF, cut to the height of the door. So after you router in for the hinges on the door you know that the template on the jamb just needs to be 3mm down from the head. Perfect alignment made easy. 5: Obviously router in the latch striker plate and hole, before the permanent jamb door stop. Scott, you should get a pair of those overalls as well !! And for Ray.
@johnpauldekeyzer8899 2 ай бұрын
It was really nice to see you and jess working together and joking around having fun with each other. Always opt to be goofy and patient instead of short and frustrated.
@ianfotheringham 22 күн бұрын
that last sentence you dropped, to a dude who knows what's what,, is supes dupes akin to telling an upset woman to 'calm down'.
@nichj487 2 ай бұрын
Two things: - Jess’ boiler suit is epic and I’m obsessed - Watching you two do tasks like this together is so charming and wholesome
@scottieB17 2 ай бұрын
New merch?!?..... Also love when Jess says: "This is really handy. I see why you like all your little tool bits and what not."
@swbjackson 2 ай бұрын
When I was taught to hang a doo rover 40 years ago the first job was to sharpen your chisels. Then you would sit astride the door, mark the hinges and chisel them out. You would drill the pilot holes with a hand drill and tighten the screws by hand, or if you were reckless, use a yankee screwdriver. None of these new fangled philips head screws either, slotted all the way. The lock was fun boring out the holes with a bib and brace.
@DamienMcGuinnessKiwi 2 ай бұрын
How far technology has sped up this process is kind of amazing. We take battery powered hand-held routers for granted, but for some jobs nothing comes close.
@gervasebarnes 2 ай бұрын
I always hang a door with frame attached, as it comes from prehung. I always hang my own doors, and so loon as hinge side Is plumb, and you can just nail In. Or, adjust to PLUMB, using packers or fox wedges. With new door, latch, then nail on door stops, so you get a perfect latch.
@couldabin 2 ай бұрын
Love Jess's reaction when you told her that you can buy pre-hung doors. I bet the conversation which followed was an interesting one. In my youth, as a salesman and Manager for one of the UK's largest door manufacturers, we introduced the first "doorsets" to the market. Architects loved them as a way of improving standards in the industry, saving time and money etc. Builders less so. Fifty years later, it seems they have become the norm. For most folks!!
@jarrettmcdaniel 2 ай бұрын
I manufacture interior doors for one of the largest "pre-built" home manufacturers in the USA and we have a machine that routes the hinge pockets in the door and on the jamb, along with routing the strike jamb, drilling the hole for the latch in the strike jamb, routing and drilling the hole for the latch on the door, and bores the knob hole in the door in about ~45 seconds. It also applies the 3 hinges at the end of the routing/drilling process. We push out about 300 interior doors a day. All hollow core. It takes an insane amount of patience to do it your way. Thanks for the vid!
@jonathanrashleigh8771 2 ай бұрын
And this is why one day soon no one will have any other skills than lifting things and pressing buttons on machines. And hey robots can do that for you too!
@aidan314 2 ай бұрын
@@jonathanrashleigh8771 People probably had the same comment about blacksmiths back in day.
@TAH1712 2 ай бұрын
Your right - it takes patience and practice, but also the learning experience is transferable to other problem situations.
@daveperkins2927 2 ай бұрын
Nicely done.👍 It's called a hinge leaf, and the leaf that connects to the barrel in three places should be fixed to the jamb, and the leaf that connects to the barrel in two places should be fixed to the door.
@ryanhernandez8388 2 ай бұрын
I heard it's called the hinge labia, and the only important part is the cliteringe
@garywalshe4726 2 ай бұрын
most to the post is how we were told to remember that 😂 as in the hinge leaf with 3 tabs goes to the frame and the 2 go to the door as you say
@raymihurtadostuart7052 2 ай бұрын
Huh I’d never considered that.
@Dazza19746 2 ай бұрын
@@ryanhernandez8388 only at the apprentice level is the cliteringe deemed important, for far better lubrication and long lasting satisfaction you need to learn about the Gee spot, but no point discussing this when most wonder what flap goes where 🤷
@barnabaas79 2 ай бұрын
LOL - Maybe the best final cut yet. Her reaction was so sincere!! Now you gotta teach us your tricks for how to fix doors that WERE NOT hung properly and close by themselves or fall away slowly. Yes I know there's many videos on that out there but in Scott I trust!
@ChrisMurley 2 ай бұрын
A brilliant episode. Almost a carbon copy of my wife and I hanging doors. Made all the brighter by Jess' outstanding overalls and the brilliant questions You should involve Jess more, she just brightens everything.
@benoithudson7235 2 ай бұрын
Jess is me when I first got into carpentry. Asking questions, getting an answer, realizing I don't know enough to understand the answer, ask more questions, and keep going until the answer is "turtles all the way down". Scott is more patient than my teacher was :)
@Torchedini 2 ай бұрын
And some fun Scott impressions along the way. Always fun when somebody else knows you a bit too well.
@Raysways1 2 ай бұрын
Heavy Friedman vibe in this one. Keep them coming!
@hw2508 2 ай бұрын
Some couples would not be able to do what Jess and Scott have shown us here. It would have ended in an argument etc.
@Dazza19746 2 ай бұрын
I was in the 80’s my teachers were more about bullying, hitting and 95 percent verbal berating, all day being told how useless and worthless you were, it was worse in front of a customer that you liked. I remember I discovered what being ‘close to death’ feels like, sort of euphoria actually when you’re chocked out and you really ’see stars’ All I learned I ‘stole’ figured out for myself, read books, technical college and F’ing up Still learning yet maybe 35 yrs later, I’d never treat anyone that way, but it does irritate me the younger folks ‘expectations’ that you’ll just tell them everything and you sort of ‘owe them’ My skill and knowledge for what it is was hard earned.
@raymihurtadostuart7052 2 ай бұрын
@Raysways1 what do you mean?
@bunning63 2 ай бұрын
Good memories, being told I was taking toooo... slow. This was followed by a demonstration from my estimed leader on door installation. There were many, many doors in this house, about a week later the owner comes up to me and tells me the leader told them I had installed all the doors, and there was a problem with one of them. Well you can guess which one, I told them that my leader had installed that one so best they spoke with him. Once they had left he comes up to me quite flustered but asking how we would fix it from jamming. Seizing this opportunity, like you would, I explained how important it was you did these jobs once, right., and now he had a problem as he had Gibbed around it etc. He's like "well, what do we do now" notice the 'we' which became singular after muttering that could I just fix it. Doors were never discussed again. Speaking of custom doors, yeah had one here where the frame and door had warped. Turns out it was a 'State House' special. Even the jambs were odd sized.
@davidmoynahan9585 2 ай бұрын
The "Kenny 3D Jigs" are pretty cool. Having the right tools defiantly makes for a great job. Showing the world the special tools and how to use them is worthy education, like when Gaston is showing the tools he supplies. Think Kenny should meet Gaston.
@geraldweckesser9556 10 күн бұрын
New to the channel, subscribed because of Jess. Showed my wife. It's good to know we are not alone in our workings around the house.
@Barrysautospares 2 ай бұрын
Ahhh, another SBC Saturday. My wife is a pharmacist, and there’s a local GP, Dr Scott Brown. Every time she sees one of his scripts she says to herself “It’s Scott Brown here!” The funny thing is, she doesn’t even watch the videos, she’s only ever heard me talking about them.
@DebsHill1 2 ай бұрын
love the training session 😂😂 and Jess face when she realised you can buy the door already done 😊
@aggroroo 2 ай бұрын
“Yeah if you ask a question on every step” - every husband knows EXACTLY how Scott felt when he said it to Jess 😂😂 her comeback was top notch too!
@GIRAF92 2 ай бұрын
Isn't that how you learn?! FACTS 😂
@user-bu8mv3xy9m 2 ай бұрын
I have always taken the old door off clamped it to the new door transfered the hing locations perfect every time
@tonypowell6445 2 ай бұрын
Hi Scott here in the UK we call the flap part is a leaf and the barrel is known as the knuckle
@steventhomas9461 2 ай бұрын
And in New Zealand as well.
@JamieVauxnut1 2 ай бұрын
In Scotland its barrel and leafs the knuckles are the segments on the barrel , normally 5 parts
@albertsmart1221 2 ай бұрын
Leaf, Knuckle, Pin. In Australia
@colinurquhart7502 2 ай бұрын
I use a plasterboard trumper to hang door. Nae sure proper name of the lifter ats fit i call it in north east scotland
@simeonmartin3514 Ай бұрын
Not many people would know this here in the US but each hinge has 2 leaves each, leaf has knuckles and a pin holds the knuckles together to form the barrel. 3:27
@AncoraImparoPiper Ай бұрын
Jess' assessment of the difficulty of hanging a door is helpful to us novices because watching the pros do it so flawlessly every time makes it look easier than it is. And when I get around to doing it, at least I will know that it is bloody hard. BTW, I thought Jess' overalls were safety gear for easy visibility on the work site. It would def work. How can anyone overlook a sea of flowers in the middle of the yellow hi vis crowd.
@thomashverring9484 Ай бұрын
Jess asking what the flat part is called is the thing I would do when learning something new. And, as an aside, in development and design phases it's also why you should bring in people from outside your expertise, because they ask questions and see things you don't even consider.
@heleuma7937 2 ай бұрын
The only thing that would make this episode better is if Scott had overalls to match Jess
@vanDeudekom 2 ай бұрын
Nop!
@mandyleeson1 2 ай бұрын
😂 Thanks for the imagery!
@XXXAgentMulder 2 ай бұрын
Those overalls that Jess wears are classic! 😀
@stevoknevo1970 2 ай бұрын
He's need to get Ray a pair, covered in tulips of course...or cannabis leaves, whatever Tracy can sort out...
@GumbootZone 2 ай бұрын
One difference I do, is after marking the door hinge centres, then BEFORE I rout it, I clamp on the jamb and square the marks right across. That way, if one measurement or pencil mark is not quite right, at least it will be a perfect match for both door and jamb.
@bobbushca797 2 ай бұрын
YEP ,done it for years this way as i dont trust my tape either , i never get it wrong this way , great epp as always.
@Lettarr 2 ай бұрын
Man I love those videos on a Saturday morning with a cup of coffee. Keep them coming
@bjornnz2367 2 ай бұрын
Scott will need to do installing a pre hung door one now so he can go into detail on the shims and hardware install.
@anthonypayne1782 2 ай бұрын
I’ve been waiting for your how to hang a door for years now!
@itsryanbrah3864 2 ай бұрын
Kudos to Scott, being the perfectionist that he is but also willing to teach on his own home. If Jess had ruined something he would have had to buy a new door or forever live there knowing that it wasn’t right. That for sure must have been the most stressful part.
@DamienMcGuinnessKiwi 2 ай бұрын
That automatic center punch at 8:15 is awesome. Didn't know those existed - definitely getting one for the workshop.
@JosephPuplava 2 ай бұрын
Ha! She has great humor. 😂 The door looks precise and good. I can't wait to see the house once it is completed.
@gerrymcintosh4477 Ай бұрын
I taught my wife a lot contruction/ carpentry skills years ago. Today, I would bet a beer, she could match skills with the best of them. Also, she could wire a house and basic plumbing. She was able to renovate a kitchen and bathroom. Last summer she installed flooring and baseboards all her self as I recovered from a stroke. Keep teaching your wife as I’m sure she can do it. Good luck Sir.
@mrharcore 2 ай бұрын
I don't know if Jess' reaction to hearing about pre-hung doors was genuine, or just great acting but I loved it.
@marinalira7434 2 ай бұрын
Loved this episode! It’s great to watch Jess learning new things. And I love the overalls! 😍
@katrinabell7684 2 ай бұрын
Well done Jess for your perseverance & Scott for your patience.😎I love your garden overalls. The new pair looks cool too! 💐🍂🍁a great start to my Saturday.😎
@MaximumNewbage 2 ай бұрын
Nice. You should do more in depth tutorials on specific tasks like this. This video skews more towards educational in focus while still being entertaining. And getting an amateur to learn along with everyone (Jess) was a great touch. Serves as a great sanity check, since if Jess gets it, then you know the instruction is good and comprehensible. And Jess asks great questions that a beginner would like to know that a pro might not even think about, like what you would do if you didn't have a full workshop. The byplay between Jess and Scott also adds great on screen chemistry and entertainment value. Very well done video! Particularly oustanding even among your ordinarily excellent content!
@calvinnash5527 2 ай бұрын
Another great episode S&J......love the place, love your work.
@terrytopliss9506 2 ай бұрын
Pleased to see Jess having a go at door hanging Scott,thanks for the latest exciting episode.👍👍
@ryanmccrae9491 2 ай бұрын
Please do more videos like this. Super useful
@heavypiano 2 ай бұрын
What a great video. Thank you so much for taking the time to add value to the world!
@DGALVIN45 2 ай бұрын
My favorite channel on KZfaq. Love the content Scott 🤌
@asus9596 2 ай бұрын
The thumbnail cracks me up. What were you looking at? The camera is over here! 😂
@SylviaFawley 2 ай бұрын
Really enjoyed the video, well done Jess , Love the new overalls 🥰
@lisaferrara8120 2 ай бұрын
Great tips throughout the video!!
@jakefreeman6024 2 ай бұрын
7am Sunday morning, cup of coffee , toddler has her milk, and we sit watching Scott brown, could life be better?
@rulowth4815 2 ай бұрын
The pre hang was HILARIOUS
@nealbarker7026 2 ай бұрын
Loved this, sat at work having lunch and thought, not watch scott for a while, one to see his newish how too, and jess involved, smashed it, and the very very end had me in stitches lol, pre hung are no fun lol
@ralphprice5619 2 ай бұрын
Great questions from Jess 👍
@SivertBerge 2 ай бұрын
Loved this episode, you make a great team!
@multileroy2000 2 ай бұрын
The old hinge leafs 3:16! Love the videos, keeps me passionate about my trade in a world of de-skilling!
@user-pq7ii7kh7m Ай бұрын
Thank you for your generosity in sharing this wonderful and beautiful thing with us Although carpentry work is exhausting, it seems easy and beautiful to you I congratulate you on reaching this level in your life
@arielleon7236 Ай бұрын
First time I come across this channel and this woman makes the video 100 times more entertaining. She represent all of us who need things explained a couple of times before we get it.
@rob1971 2 ай бұрын
Well done Jess, awesome job!!
@aaronblackford981 Ай бұрын
And the fact her first power tool, she said it, was the router. Omg. She’s a firecracker. Awesome build
@blakewilkin552 2 ай бұрын
As a soon to be mature age apprentice, absolutely love this type of video. So great guys!
@mtrhodesy 2 ай бұрын
I sometimes wish I couldn't hang a door! Mates are always asking me to 'just hang a couple of doors bud, won't take you long'....
@smalljoel8335 2 ай бұрын
A gift and a curse
@mtrhodesy 2 ай бұрын
@@smalljoel8335 Absolutely, great at times, and terrible when mates want fire doors hung on the third floor!!
@odinncool 2 ай бұрын
Hate when mates do that
@terrywing7229 2 ай бұрын
Not to be that guy but, always charge for your work. Your time and skills are worth something. Undervaluing ourselves is why Carpenters are so lowly paid
@aidan314 2 ай бұрын
@@terrywing7229 you charge your mates? Would probably explain why you do don’t have many.
@paulnolen7651 2 ай бұрын
Great video you guys are too much fun thank you thank you😊😊😊😊
@mrsarkey 2 ай бұрын
Scotts passion for hanging doors is enchanting
@sowbirasmujo 2 ай бұрын
Gotta love that floral onesie 😃 Go Jess!
@matthewhall435 2 ай бұрын
This is perfect timing im putting some doors in soon for a wardrobe !
@RHEC1776 2 ай бұрын
🤣🤣 Don't ever ever get rid of Jess. She's amazing and hilarious 🤣🤣
@terrywing7229 2 ай бұрын
Great episode, reminds me of having to hang 4 doors when I was working in Tonga 25+ years ago, no router so had to chisel the hinges in. Enjoyed the Prehung door gag, for your next trick show Jess two piece jamb with Architraves pre installed, easy to set up for packing and a bit of expanding foam so they don't move. Another tip, look for 'Jolt' screws, our painters love it when we use them.
@MrLeeziebee 2 ай бұрын
Cools seeing jess involved and great choice in floral pattern.
@Oblimix 2 ай бұрын
I'm liking the new thumbnails. Adds a bit of humor to it.
@fionamonahan8771 2 ай бұрын
Jess is fantastic with the garden and the tools
@tauzortron 2 ай бұрын
As a beginner, I really appreciated this vid :)
@matatattat 2 ай бұрын
PLEASE bring back the merch if possible. My old shirt has seen the abuse of putting in too many doors ;( Love you guys!
@jonathandevries2828 2 ай бұрын
Jess, youre good at stuff!
@MrTherbst 2 ай бұрын
I got some invaluable advice from on old carpenter about hanging doors that l would like to share with other KZfaqrs. He told me its a lot easier to always start on the hinge side first.
@appahman 2 ай бұрын
Scott and Jess, squarespace.. all the things! Jess is great with you on camera Scott :) all I could use now is smoko time, for old time sake!
@mandyleeson1 2 ай бұрын
Have to confess I got a bit lost with how we got to 1989 and 1992. I loved this exciting episode.
@mrglsjr 2 ай бұрын
That extra 3mm came from the floor not being level (9:00 - 9:24 in the video). The jamb on the knob side of the door needed to be 3mm longer. I hope this helps!
@mandyleeson1 2 ай бұрын
@@mrglsjr Thanks Greg that helps alot :-)
@DamienMcGuinnessKiwi 2 ай бұрын
Great video Scott. For the rest of us, if you (or a friend) have access to a 3D printer there are lots of hinge jig designs available online.
@crumpet_ 2 ай бұрын
Fantastic episode. I feel like we've come full circle
@markbray3038 2 ай бұрын
More Jess, really good video.
@laperez1996 2 ай бұрын
Scott, would recommend Jess document and film her gardening journey. My wife is starting a garden this summer and she enjoys Jess bits on the channel. Just a thought, but love the content here in Chicago, IL!
@roadie3124 2 ай бұрын
I've got a pair of those lifter things. They work really well.
@andyraven6219 2 ай бұрын
Awesome episode. In the London it's Hinge knuckle and leafs Door linning = head and two jambs, usually internal Door frame = head and two jambs plus a cill usually exrernal
@wilf.tanser9961 Ай бұрын
Door Lining out of 28 or 32mm material. Stops nailed on only. Door Casing (old properties or external doors) 75mm thick material. (so 4x3 or 6x3) with stops rebated in.
@shootsteel 2 ай бұрын
Great jig design with access for dust collection
@mycoolcar 2 ай бұрын
Great episode
@sheepforwheat 2 ай бұрын
great chemistry in this vid
@JasondenHollander-qj5hp 2 ай бұрын
I like the way u used those two Japanese saws on the bottom edge of the jamb. Nice.
@markarita3 Ай бұрын
3:06 VERY important...nice catch Jess!
@danbrown3460 Ай бұрын
When I am measuring existing hinges I find it easier and more accurate to use a long strip of wood as a story pole and transfer the hinge markings to the strip of wood and then mark the door to be routed
@thebeuks1 2 ай бұрын
I have my grandparents front door that i received after they passed and their house was demolished. It is a solid cedar door. It is 20mm smaller than a standard door here in Aus. 2020mm is the door so i need to fiqure out hot to redo the jam to make it fit or extend the door by 20mm.
@RyanYoxo 2 ай бұрын
I finished my apprenticeship, went off on my own for about a year then got out of carpentry and only been doing the odd job here and there for the last 5 years Almost forgot how to hang a door haha, cheers! Mostly just getting the gaps right etc. I could only briefly remember to add 3mm to the jam hinge
@thecraftiekiwi4919 2 ай бұрын
love your overalls jess.
@umoramayori 2 ай бұрын
I usually pull the exsiting door, use a square to transfer hinge locations to the new door. Especially on entry doors where you routinely have to trim the door slab to fit the opening.
@paul4124 2 ай бұрын
I’ve hung many doors in my life and l have just learnt something that I didn’t know. That there is an angle on the edge of the door. Great video Scott, just goes to show, we can still keep learning.
@lach517 3 күн бұрын
In Aus they aren't. I usually manually put one on. Most chippies here won't though.
@brycecomerwoodworks Ай бұрын
Awesome video! :) Funny that you put a tick on your mark. That indicates to me that i should be cutting on that side of the line. For a centre mark, i'd put a "C" on it.
@JasondenHollander-qj5hp 2 ай бұрын
When I grow up I want a woman who can wear an outfit like Jess’s. Sensational! Edit: that woman at the market making this suits needs squarespace!!!
@SmallWonda 2 ай бұрын
Ha-ha! Hilarious!! Scott, I think you need a custom Garden Suit, too! I guess that's in Nelson? Thanks!
@espnmk 2 ай бұрын
the leaf of the hinge the flat parts, lol thanks for sharing Scott
@Dazza19746 2 ай бұрын
Love your hinge jig with dust port, brilliant idea mate
@garrydickinson4839 2 ай бұрын
Great channel, I wish you had included setting the router depth. What was the gadget you had in your drill when drilling holes?
@MahKryte 2 ай бұрын
Can we have more of "teaching Jess to do stuff" please? Absolutely brilliant
@dutchgray86 2 ай бұрын
Not even a rebate on the head of the lining (jamb) for the sides, let alone the using of a tongue and groove joint that you never see now as it takes too long. Also I was taught 5 pairs of fixings per side, but you only see 3 now as it takes too long, plus we fit the lining before plaster but don't hang doors until later so the linings have to be put in plumb, square, head level, sides straight so that the door will actually fit by the time you get there to hang it.
@MarcusMussawar Ай бұрын
that product drop was fantasic
@markoshun 2 ай бұрын
Great video. Was that a Carhartt garden jumper? Lifelong carpenter. People are often surprised I rarely hang doors and only heritage/specially stuff. By the time you gather all the jigs and tools and then measure, calculate, rout and predrill -and Scott didn't even drill for the lockset here yet- meantime I've already installed all the pre-hung doors in the basement and half finished lunch. And as he said, it's even more time-consuming to do this without all the jigs, stands, and centers.
@chrisburns5691 2 ай бұрын
nice video. That hinge jig is pretty cool, with the vacuum attachment. way easier than having the vac hooked up to the router, which can be a bit clumsy moving it around and being able to see right down on the work.
@kyzenlanx 2 ай бұрын
That's what I was thinking when I designed it, my mate is in commercial and does hundreds of doors a day; much easier not to have to drag the hose around on the tool, safer too I reckon.
@chrisburns5691 2 ай бұрын
@@kyzenlanx nice, do you sell them? I bet once people saw that feature you'd do well.
@tyoung7528 2 ай бұрын
Love those overalls! Beats my Carhartts hands down!
Action C Mini
Рет қаралды 59 МЛН
Xuân Đông Vlog
Рет қаралды 12 МЛН