Installation assembly cover brakes brembo. necessary: silicone, scotch tape, diluent, cutter INSTAGRAM / cars_and_furious_ FACEBOOK bit.ly/2fdn7Fo TWITTER / carsandfurious_ If you love cars you should subscribe
Пікірлер: 121
@TZAK4u6 ай бұрын
Great video. Thanks for posting
@carsandfurious_6 ай бұрын
You are welcome 🙂
@leonardfedillaga3 жыл бұрын
What i do i put heavy duty magnet all in place👍👍
@danrook57573 жыл бұрын
Can I do this on my monte carlo
@danrook57573 жыл бұрын
Can u use heat silicon that is red used on fireplaces
@carsandfurious_3 жыл бұрын
It can also work that silicone. Not sure if the grip is strong
@richardbrowne36419 ай бұрын
What was the name of your sealant? How long did you let the sealant set and dry? I just bought a set of Chinese Brembo caliber covers.
@carsandfurious_9 ай бұрын
Hello, the sealant is the Bostik poly max original express. i did the work in the evening and next morning you can travel perfectly
@richardbrowne36419 ай бұрын
@@carsandfurious_ 👌
@carsandfurious_9 ай бұрын
@@richardbrowne3641👍
@moha49173 жыл бұрын
Witch size should I buy for my MK7 TDI ?! Btw than you for vide . 👌👌
@carsandfurious_3 жыл бұрын
Hello, these covers in the video are: front 27 cm length, check the length of your brake caliper. Thanks 👌
@moha49173 жыл бұрын
@@carsandfurious_ thanks 😎👍
@carsandfurious_3 жыл бұрын
@@moha4917 👍👍👍
@expertopinion8111 Жыл бұрын
The large covers about 10 inches in length and the med about 7.2/7.5 ?? In length put 2 small screws in them instead of all that glue
@richardbrowne36419 ай бұрын
I bought mine on ebay.
@MrArjanOskam4 жыл бұрын
Is it now hard to replace brake pads with this mounted?
@carsandfurious_4 жыл бұрын
Hello, no on some cars you don't have to disassemble you can replace the same. on other cars just cut the silicone to remove them
@MrArjanOskam4 жыл бұрын
Ah Thanks!
@MrArjanOskam4 жыл бұрын
@@carsandfurious_ I am pretty sad tho, I have like that metal rod design brake... Which means I have a metal rod coming out of it...
@sarahromero73763 жыл бұрын
Will fit 2017 Dodge Durango r/t
@carsandfurious_3 жыл бұрын
Hello, I think so. however the largest measures that make these covers are: front 27cm rear 24cm. If your brake caliper is longer it will not fit
@eneatipo9Ай бұрын
y con ese pegamento soporta el calor de los caliper?
@carsandfurious_Ай бұрын
Hi, yes yes perfectly. Just think, I had those covers and the car for 4 years, never any problems
@nullgamer19765 жыл бұрын
But when you Want to change the brake did you must do this again every chnage of brakes
@carsandfurious_4 жыл бұрын
Yes, on some cars you have to redo everything every time you change the brakes. on others not.
@nullgamer19764 жыл бұрын
Okay thx
@marcosalerno34473 жыл бұрын
Crazy. What if it detach? It is not safe
@carsandfurious_3 жыл бұрын
Hello, no the important thing is to position them well. Assembled 2 years ago and still are there.
@ciprianslatineanu4403 жыл бұрын
@@carsandfurious_ did you replace the brake pads ???
@carsandfurious_3 жыл бұрын
on some cars you can replace the brake pads without removing the cover@@ciprianslatineanu440
@ayenunu Жыл бұрын
He will fix it again...He's a Genius.
@savage_han3 жыл бұрын
I ordered a pair from eBay and got the small- medium. I drive a Scion xB and they won’t fit!! What size are these?
@carsandfurious_3 жыл бұрын
Hello, message arrived late, these are large and medium size
@arod93713 жыл бұрын
How do you change your brakes?
@carsandfurious_3 жыл бұрын
Hello, when you need to change the brakes remove the cover. on some cars it is not necessary to remove the cover
@AlvlUpSavedMyLife3 жыл бұрын
Anyone know what ones will for a 98 Audi A4? Thank
@carsandfurious_3 жыл бұрын
These fit for audi A4. you have to choose size M and L
@localmediaMY3 жыл бұрын
What glue did u used? Was it silicone glue?
@carsandfurious_3 жыл бұрын
Hello, yes from Bostik BOSTIK Poly Max Original Express. Very good product
@azo0oze_86 жыл бұрын
How can I change brake pads after installing brembo
@carsandfurious_6 жыл бұрын
just cut the silicone with the cutter.then he resigns
@carsandfurious_6 жыл бұрын
cut the glue with the cutter.
@zaoulboodhun71375 жыл бұрын
Thanks
@carsandfurious_6 жыл бұрын
no heating of the brakes.no problem
@expertopinion8111 Жыл бұрын
Better way us just put to small drill holes and screw it to caliper easier and a lot less time
@carsandfurious_ Жыл бұрын
Hello yes also so. But I can tell you that by doing as in the video, I've never had any problems, none have ever come off, zero problems
@GIOX96K8 ай бұрын
Where i can find this cover?
@carsandfurious_8 ай бұрын
Hi, they were easy to find before. I bought them at a car tuning shop
@mysteriocodm84007 ай бұрын
Questo silicone è ad alta temperatura???
@carsandfurious_7 ай бұрын
ciao, non so esattamente che temperature riportava, parliamo di un video di alcuni anni fa, però su varie auto ho utilizzato questo e non si è mai scollato
@yokev_56116 жыл бұрын
Looks nice! But it’s a waste of time. You will basically get rid of it, every time you’ have to change your break pad. What if one day you’re driving on the high way and this thing comes off?!!!
@carsandfurious_6 жыл бұрын
Put putty for glass windshield. it will never come off.
@mbahjenggotvloq10 ай бұрын
😅😅😅😅
@bradz24516 жыл бұрын
kinda makes me nervous that this would over heat the brakes.
@carsandfurious_3 жыл бұрын
no problem for two years
@rosalvoneto80 Жыл бұрын
The rotors will not be affected by this.
@mathlengachhangte24123 жыл бұрын
How much time required the silicon to get hard?
@carsandfurious_3 жыл бұрын
Hello, 3-4 hours, but you are advised to work in the evening and you can use the car 100% in the morning
@oropeza1905 жыл бұрын
SOMEBODY COME GET THEY MANNNNNS WHOO TF WHOOOOOOOS MAN IS THIS 🤷🏽♂️
@davidcharles46363 жыл бұрын
Where did u get these?
@carsandfurious_3 жыл бұрын
Hello, on ebay, but now I can't find them anymore. I needed others
@srtmacmx43103 жыл бұрын
Link
@carsandfurious_3 жыл бұрын
Hi, unfortunately I bought them in the store. try to see on aliexpress
@marontinko95393 жыл бұрын
Side
@shawndenman9413 Жыл бұрын
What a great idea stick them on with silicon 🤣 Best way is drill two Holes screw them on then when you change the brakes you just unscrew them far better than sticking them on hoping they won’t come off
@carsandfurious_ Жыл бұрын
Hi, I've now sold that car, but I've had the silicone covers for 3 years and they've never come off, even doing a lot of km.😅
@juliem79693 жыл бұрын
No thanks I’ll stick with painting mine thanks
@jamiewilliams75846 жыл бұрын
If your going to fake it at least put the break fluid drain at the bottom
@carsandfurious_6 жыл бұрын
NOOO!real brembo, fluid drained at the up. always!!!
@plantfittermobilerepair91254 жыл бұрын
High performance callipers always bleed at the Top buddy
@robabrnts90574 жыл бұрын
Every Caliper
@AlvlUpSavedMyLife3 жыл бұрын
Yea put it at the bottom so no air comes out when you bleed it. Great thinking Williams xad
@mohammedmuneer63763 жыл бұрын
It is should be upside down
@carsandfurious_3 жыл бұрын
Hello, no no you must always mount with the bleeder (the screw with the cap) at the top
@mohammedmuneer63763 жыл бұрын
@@carsandfurious_ I’m 100% sure it should be the opposite
@marontinko95393 жыл бұрын
Up-down...
@carsandfurious_3 жыл бұрын
Hello, they must be mounted with the tube below and the bleed screw above
@donmak1443 жыл бұрын
Fake it till u make it
@carsandfurious_3 жыл бұрын
😄😄Many just like aesthetics
@VERIFIED_COMMENT5 жыл бұрын
Wrong way to install these go on (red memory) channel he puts them on the right way no glue
@carsandfurious_5 жыл бұрын
With this type of silicone there are 2 years do not detach
Red memory did them better but he installed them upside down 😂😂😂
@kanatipz61476 жыл бұрын
just save the money and buy real calipers you need to pay attention to the safety
@dflex41802 жыл бұрын
okay you give us the $400 for them lol vs $20 no safety issues w covers
@henrykwodek4039 Жыл бұрын
😭😭😭😱
@roybm31246 жыл бұрын
Are you 12 years old?
@dougwall6752 жыл бұрын
Too bad audi brakes are way different than American cars
@dflex41802 жыл бұрын
lol again how? brake pads, calipers and same shit my u are the negative one
@dougwall6752 жыл бұрын
@@dflex4180 they are not the same dude lol. Take a look at other cars.
@gianlucacavalieri52625 ай бұрын
sto male
@sumikaa702 жыл бұрын
What? 😂😂
@MrEnteng07074 жыл бұрын
Pimp my ride low budget
@danrook57573 жыл бұрын
Carl Poppa : is this ultimate cheapskate
@Luccas36803 жыл бұрын
Why???🙈🤮
@carsandfurious_3 жыл бұрын
😄They are whims
@saby87653 жыл бұрын
Wait what? This is fake!
@juanosoriorosales13846 жыл бұрын
que ganas de hacerse pendejos jejejeje
@carde933 жыл бұрын
Quindi ci voglio 20 min per mette un cazzo di silicone porca troia che nervoso Maremma cane
@carsandfurious_3 жыл бұрын
si, poi devi aspettare che secchi il silicone. ti consiglio di farlo di sera, così il giorno dopo sei sicuro che tutto ok
@itechuknet6 жыл бұрын
eBay specials 😂😂.. who uses glue??
@carsandfurious_6 жыл бұрын
high temperature glue. no problem
@yammakashi3 жыл бұрын
Seems dangerous to use.
@carsandfurious_3 жыл бұрын
Hello, no no problem. Fitted a few years ago never unglued.
@dougwall6752 жыл бұрын
Also wouldnt ever suggest putting any type of glue on your braking system ever. This is coming from a mechanic
@dflex41802 жыл бұрын
its silcone lol as a mechanic you should know this DOES NOT mess anything up in the breaking system...its on the exterior
@carsandfurious_2 жыл бұрын
@@dflex4180 True. mounted for 2 years no problem 👍
@robloxunspacecommand1935 Жыл бұрын
Trolled
@raffaelebonazza11063 жыл бұрын
A parte il fatto, anche fossero pinze Brembo originali con quei cerchi non li vedrebbe nessuno, ma scommetto che alla prima discesa ,appena si sono riscaldate le pinze il caro polimax si è scollato e la cara coverina si distrutta tra il cerchio e la pinza stessa, bello schifo di video.
@carsandfurious_3 жыл бұрын
Ciao, no le misi più di 2 anni fa e non si sono ancora mosse, ora l auto non ce lo più, ma la vedo in giro con ancora le cover. Io ho pulito bene le pinze e nessun problema.
@MartinAston003 жыл бұрын
DO NOT DO THIS!!! If you have to GLUE, you got the wrong ones, or they just don’t make any that fit your calipers. ...but NEVER glue them to your calipers! ...smh... 🤦🏽♂️
@carsandfurious_3 жыл бұрын
Hello, I glued them 3 years ago and they still haven't come off.
@biohazdarx6 жыл бұрын
Ridicule
@yokev_56116 жыл бұрын
BIO a oui je pense la même.
@saltdog555 жыл бұрын
LMAO these covers don’t fool anyone! Never seen anyone work so hard to install a piece of plastic that COULD fall off while driving, then what?