I still get questions about this old issue two years later regarding the fix specifics. I was able to locate the shop invoice and read that the main cause was a broken pin (number 29 in my case) in the connector to the electronic control module (ecm). Additionally the fuel sending unit was bad and was replaced. The shop technician spent 12 hours troubleshooting my root issues and even replaced the ecm itself (which turned out not to be bad) as part of the troubleshooting protocol.
@jonnyone24 Жыл бұрын
My skid steer was in low power mode was driving back through a field hit a big pile of dirt, with the bucket engine bogged down and shut off and now it will not start.
@daven11515 жыл бұрын
What did you find out? Mine was throwing around 30 codes and it was the wiring harness. Then it was popping the instrument cluster fuse and it was a wire by the starter grounding on the engine block. That 1 was my fault where I made a butt connector repair years back and wire came exposed.
@ozranch94793 жыл бұрын
I am having similar problems. Was hoping you had an easy answer. Mine always starts but shows a code prior to starting and won't come out of limp mode. I've noticed that the glow plugs cycle when it;s going to work and run right. Guessing there's a wiring problem somewhere. 2013 SV300 1500 hours. I think the electrical component installers at the factory were careless or incompetent.
@nathanjenkins91183 жыл бұрын
I know this is probably really late but anyways. What I noticed when you hit the power button, your supposed to get a clicking noise, this being the fuel pump. Every machine is different, but from my experience, when power is on before engine crank, there is a clicking noise. You might also get the glow plug light illuminated followed by a countdown. In the keyed variant, this just allows the engine to crank. I’m not sure about the keyless version if the solenoid clicking is for the starter, but has a protection feature disabling the starter if the fuel pump is not working. I don’t know much about trouble codes, and I could be way off from what the problem really is/was, just thought I’d share my experience. Let me know if that was the issue if you’ve got it fixed by now.
@jamesmatte45482 жыл бұрын
I'm having a very similar problem with my 2016 SV280. Just clicks in a couple different places, sometimes it'll just fire up and everything works fine till it sits overnight or a few days. Isn't the battery. I bought a new one for nothing. I'm hoping to tilt cab tomorrow and see something obvious but I doubt it
@j.alanmorgan2 жыл бұрын
James, have you checked your master power relay? On my TR320 its in the cab at my left foot.
@rogerspegal93774 жыл бұрын
I have a question I have a TV380 and it runs great but as soon as it starts the stop light will come on and the machine won't move the lift works. The only fault code is 4745. Please sir help
@nathanjenkins91183 жыл бұрын
Roger Spegal only thing I somewhat know about this is something to do with hydraulics. I’ve been looking for answers too, my main theory is hydraulic oil level is low or overheating
@curtissawyer5128 Жыл бұрын
Loose battery cable was 1051 code on my skid steer
@j.alanmorgan5 жыл бұрын
Hi Curtis, I did get the TR 320 working properly. Had to have it trailered to the dealer and after much searching.....found out that an electrical connection to the main controller unit needed to be soldered and secured properly. Over $2k including transport to fix. Yikes....but she is working fine!
@funnyklown15 жыл бұрын
Have had similar issues with a case. Great machine other than it randomly doesn't start. Bypassed the seat sensor from behind the seat. Any chance you could make a video on what and how they fixed it so we can all see exactly what went wrong?
@ntotheb97374 жыл бұрын
@@Jayybub I'm with ya. Can you post the work order or something similar?
@phillips10032 жыл бұрын
@@caseybrehm1242 did u figure urs out , I have the exact same issue ur describing
@hermancm5 жыл бұрын
My 05 430 shut down while plowing now won’t crank. Lights work, found a 15a lockout (or whatever you call it again?) fuse blown, replaced- nothing .. Checked fuse again not blown. Battery is new, connections good. No clicks. LCD’s go dark when key in crank then says ACC when detected to run. It’s stuck in a neighbors driveway... any ideas?
@nathanjenkins91183 жыл бұрын
Curtis Hermanson check for corrosion in the fuse boxes and wires inside the cab. If you have no clicking when the key is turned, and there is power, it’s the fuel pump
@hermancm3 жыл бұрын
Nathan Jenkins It turned out to be the tilt interlock solenoid. I unplugged it and ground off the plunger point on it so I could use the skid until I got a new one.
@96z28camaro15 жыл бұрын
Mine is doing almost the but unsure how to tilt the cab since I cant start it to raise the loader arms.
@bs563 жыл бұрын
We removed the bucket & loosed the hydraulic lines and on the cylinders and pushed it up until we could get the safety installed on the cylinder. Made a mess but the cab is up now.
@96z28camaro13 жыл бұрын
Mine had water in the fuse box and 2 bad relay's
@paulolondra66423 жыл бұрын
Respuesta
@andrewbyler81015 жыл бұрын
What was wrong mine is doing the same thing and the same codes are coming up
@legacyfarmsllc85115 жыл бұрын
Close the door😂
@ZR1Terror2 жыл бұрын
How do you cycle through the error codes? What button did you press?
@j.alanmorgan2 жыл бұрын
I had several codes that cycled every few cycles automatically. I see in my manual that you can push the aux/override button to try and clear a code. Maybe this will cycle too? Hope this helps.
@jeffersonbueno49594 жыл бұрын
Boa noite , conseguiu resolver o code 1005/1906
@jamesolexey38224 жыл бұрын
Can you please reply? I’m have a similar issue.
@j.alanmorgan4 жыл бұрын
Hi James, my issue was with a loose/broken connection at the main control board. I was not present when the service technician fix it but I was told that he soldered the loose/broken connection on the main control board. I will call the service center and see if they will tell me the exact board and connection they fixed and post the response.
@vincesmith5846 Жыл бұрын
@@j.alanmorgan What control board? Fuse BOx? Same machine and same codes.
@j.alanmorgan Жыл бұрын
@@vincesmith5846 I had the machine taken to the Case shop as this issue was beyond my fix it myself willingness. The service manager told me “pin 29 on the main control board was broken and that they located this after several hours of technicians searching”. I have no further details than this. I do not have any electrical diagrams to ID the main control board.
@robertdurham37665 жыл бұрын
Sell it. I have one that has given me wiring trouble from day one. Two wiring harnesses and numerous services calls. I hate to bust your bubble but they are the worst machine made. Mines sitting behind the shop waiting on a new owner.bought a cat 289d. Won’t ever buy another brand. The cat is light years ahead of everyone else. You will have wiring trouble with the case from now on
@ZR1Terror2 жыл бұрын
Good thing I saw your comment because I was about to pull the trigger on one with 700 hrs.