Chain Drive Spool for Crosskart/Mini Buggy/Go Kart: Affordable Easy NO LATHE (part 2)

No video

Chain Drive Spool for Crosskart/Mini Buggy/Go Kart: Affordable Easy NO LATHE (part 2)

Рет қаралды 36,201

Күн бұрын

Check Description for links to plans, detailed build series, FaceBook build group and more!
A year of development has led to this; A super strong Center Carrier for any IRS application without the need for a lathe. Built from readily available off the shelf parts along with accurate laser cut parts so you can assemble yourself for a fraction of the cost. This is what you have been looking for! I know this because as a builder I've been trying to find this for almost 20 years. Plans below show the required parts with part numbers for a complete IRS setup for 420 or 520/530 chains, .dxf files to upload for laser cutting, measurements for all parts, every single nut and bolt needed for assembly and plenty of pictures and walkthroughs. This setup is appx 56" hub face to hub face and has proven 15" or more of travel without binding. This has been missing for the home fabricators for too long. Enjoy!
-Kyle
Plans available here:
kj-raycing.dpd...
100+hp Build Series Here: • 100+HP Crosskart Build...
Budget Build Series Here: • Inexpensive Crosskart ...
2 Seat Crosskart Build Series Here: • Two Seat Crosskart Bui...
VF-1 Plans detail and Materials needed
• Crosskart Plans: KJ Ra...
Custom length chassis
• Inexpensive Crosskart ...
JD’s garage: / @jdsgarage701
Preferred tubing bender and notcher
Roguefab.com
Facebook KJ Raycing
Once you have the plans come join the build discussion
Facebook Build Group (KJ Raycing VF-1 and VF-2 Kart Builders) / 905565813954510
Instagram @kjraycing
Storefront kj-raycing.dpdcart.com
DISCLAIMER
Videos are for entertainment only, work performed in the video should only be accomplished by a professional technician. KJ Raycing will not be held liable for ANY personal injuries.

Пікірлер: 68

@user-hy7sf9xx3z Ай бұрын

I have been watching for a center setup and drive hub set up for a small industrial project . This would work very well

@profesonalantagonist 4 ай бұрын

For drilling the 4 on 110 perfectly, create a drill jig with the 4 on 100 12mm, then at 45* create the 4 on 110 10mm. You only really need 1 pattern laser cut, then you can drill both hubs before removing the 12mm studs. Perfect spacing and centering.

@KJRaycing 4 ай бұрын

Check out part three 🤓. Or look in your plans. Thank you so much for joining in on the fun, you are going to love this.

@KJRaycing 4 ай бұрын

Go Kart / Crosskart Drivetrain Made for HAYABUSA Power!!! kzfaq.info/get/bejne/fJdyqquKysjXfqs.html

@georgecain5362 Жыл бұрын

My new favorite channel I'm officially hooked

@KJRaycing Жыл бұрын

Wow what an awesome compliment. Thank you so much!

@doughpop9189 Жыл бұрын

You could use send cut send to make you a drill guide to transfer the new hub pattern.

@KJRaycing Жыл бұрын

Thank you so much for this!!! Can’t believe I didn’t think of it! You’re the best!

@WennieBAno 7 ай бұрын

I love this channel very useful

@GrahamCam 2 ай бұрын

How does using this rear end change the fabrication for the rear A arms in the VF-1 plans if at all?

@MatthewHeiskell 5 ай бұрын

This rear drive is what really sells it for me! WOW!

@KJRaycing 5 ай бұрын

This was a big one! Over two years to get this one to you guys. Thank you! 👍

@user-hy7sf9xx3z Ай бұрын

U-joints and cv joints require approximately 10deg offset to keep hard wear down (makes the rollers work) . That offset could be rearward making a slightly longer wheelbase or downward making lift

@KJRaycing Ай бұрын

Lots of guys have done that, the a-arms are flippable left to right so you can change the modes, if built correctly.

@rattlecan13 Жыл бұрын

Always keeping it budget friendly. So awesome Thank You again!

@KJRaycing Жыл бұрын

I’m really proud of this one. I hope it helps the dreamers out there get their creations made.

@johanpotgieter4318 7 ай бұрын

Thanks. Me and my son will be building one😂😂😂

@KJRaycing 7 ай бұрын

Man I love hearing this so much 🥰

@nicklepage3842 Жыл бұрын

I use a 6 spline PTO shaft and 4 bolt bearing blocks on my setup. The blocks attach to a slider bracket with bars with heim joints as adjusters. Hoping it'll hold up to the 20hp I have planned for my 3 year olds first car lol

@wisconsinbush2940 Жыл бұрын

Heim joints are the way to go

@DeathGEAR00103 Жыл бұрын

I know this is about affordability but I would just use wheel adapters. This way you would have more room for what ever wheels you want to run, if you are placing the brakes at the wheels.

@dannyberg4294 Жыл бұрын

Love the channel and all the info you provide! Definitely building one of these when I’m done with my drift car. On a side note; ditch the plates for your press. Those ones in particular (the ones that come with HF presses) are cast. They can and do explode when you put enough pressure on them. I think Swag off-road has some gnarly pictures on their site from that

@KJRaycing Жыл бұрын

Thank you and I will definitely look into new plates! Good luck with the drift car and can’t wait to see your build!

@DaneSaysStuff Ай бұрын

Yamaha Blasters have a 4x100 rear wheel bolt pattern. Wheels are available.

@jakesautofabrication Жыл бұрын

hey great video I enjoy them all I like the end game big savings to I did notice your axle explained E break ring Is a ABS wheel speed sensor tone ring or what ever lol but not a big deal all your work looks top notch!!!

@KJRaycing Жыл бұрын

Thanks! I assumed it was some kind of wheel sensor thing, I didn’t care too much as I was just getting rid of it anyway 😁

@isaneterrier6678 8 ай бұрын

Hy, you make a super kit for building the rear transmission. But I live in France, and with shipping and custom, it will be too expensive. Very nice job. Kris

@alessiofantei6077 6 ай бұрын

Perché? Sono italiano e vorrei costruirlo pure io. Che problemi ci sono?

@davidowen888 3 күн бұрын

Excellent ✌️

@TheMaddcrash 2 ай бұрын

Luv your work!

@JermaineLeeBlueprintAuto 11 ай бұрын

Hmmm i see part 2 is giving answers...

@brentmeyer6569 Жыл бұрын

Golf carts use 4x100 or 4x4” pattern same as a lot of go karts they are very easy to find wheels for.

@KJRaycing Жыл бұрын

Sweet! I have 5 crosskarts that all have 4x110 bolt patterns so it was very useful for me to convert the hubs.

@brentmeyer6569 Жыл бұрын

@@KJRaycing Definitely makes sense in your case. My comment was more for anyone building a kart from scratch they can look for 4x4"/ 4x100mm wheels and skip the lug pattern adapting step.

@apexaero Жыл бұрын

The Cog is for a wheel speed sensor.

@KJRaycing Жыл бұрын

The cog should be cut off no matter what it is used for 😉. The miata axles are perfect for these builds in my opinion.

@masoudseifallahian 7 ай бұрын

Hello, friend, I have a question, do the rear wheels stay the same at the corners?

@KJRaycing 7 ай бұрын

You don’t need a differential, check out all the driving videos I’ve made. These are not 3 thousand pound cars or trucks.

@hawksfb42 10 ай бұрын

Do you have plans for the front and rear a arms?

@elyazidzaidi6194 Жыл бұрын

very good my friend

@KJRaycing Жыл бұрын

Thank you very much

@306GokartsCustomBuilds Жыл бұрын

Nice.

@KJRaycing Жыл бұрын

Thank you 👍

@JermaineLeeBlueprintAuto 11 ай бұрын

Lol u answered it in the video 55.5 inchs hub to hub

@slotterhauze Жыл бұрын

I'm building an ultimate Wheel Horse mud mower with 4 wheel independent suspension and a snow mobile engine.

@KJRaycing Жыл бұрын

Well that is going to be an absolute riot!

@slotterhauze Жыл бұрын

@@KJRaycing I forgot to mention that it's going to be four wheel drive. I can't wait till I can take it to the trails and hills!!!

@KJRaycing Жыл бұрын

Yes! I can’t wait to see it!

@RedPill.Action 3 ай бұрын

I have an old honda xr600r engine i am thinking of putting in one of these builds. Do you think the gear shifting in the xr600r engine affect the performance of the car as opposed to running the belt clutch setup?

@KJRaycing 2 ай бұрын

They are faster with gears but fun no matter which way you choose to go.

@raulroque2484 2 ай бұрын

What are those shocks?

@JermaineLeeBlueprintAuto 11 ай бұрын

Chinesse kart rear independant suspension. Gkm200

@gabbo8304 7 ай бұрын

hi I hope you answer me, I want to ask you where did you buy this transmission block?

@KJRaycing 7 ай бұрын

If you watch the entire series on the Homebrew rear you will get your answer 👍

@JermaineLeeBlueprintAuto 11 ай бұрын

Whats the part # on that rear carrier?

@danielnunez3518 11 ай бұрын

Just wondering do you design your buggies so that the frame bottoms out before the shocks do?

@KJRaycing 10 ай бұрын

That is a suspension setup rather than a chassis design. I cover that in a separate video. But short answer they are set up to hit the bump stops just before the frame touches as the rule book states.

@wakeUPdummies 9 ай бұрын

Impressive. Algo tickle

@michaeldelke4190 Жыл бұрын

Kyle.... I tried closing all programs before trying to upload to send cut send but still no go. I have deleted the file and re-downloaded it and the same thing. I looked at the files in fusion 360 and they look great there. Just having trouble at Send Cut Send. I even tried multiple zip programs just in case. I am befuddled.

@KJRaycing Жыл бұрын

Message me.

@JermaineLeeBlueprintAuto 11 ай бұрын

How long is that hub to hub?