2008 Subaru Forester Fuel Tank Removal and Reinstall

No video

2008 Subaru Forester Fuel Tank Removal and Reinstall

Рет қаралды 9,495

3 жыл бұрын

My 2008 Subaru Forester Sports 2.5X had an evap leak on top of the tank. There weren't many how to videos on youtube for this topic so I decided to capture my approach. Not a professional mechanic, but I hope this video can be helpful. If I had to do this again - I wouldn't. Cutting a hole in the floor to access these valves is barbaric but that's what I would do. Dropping the tank took 6 hours, reinstalling took 3.

Пікірлер: 22

@samueltrassare 2 жыл бұрын

I owe you a huge "THANK YOU." I watched this video repeatedly and swapped the fuel cut valves today. This video a Chilton's manual really helped.

@ChallengerDood 2 жыл бұрын

Happy to help!

@RedBeardRebass 6 ай бұрын

Glad i read the description too, i'm gonna tackle a fuel leak at the filler hose inlet above my subframe. Dropping the rear end with the rust i've got isn't an option, so i'll probably use a sheet metal nibbler or something to cut an access panel.

@jordanbrayfield531 Жыл бұрын

Thank you so much. I have a rusted through tank and this helps so much

@robertsmith9756 4 ай бұрын

I wish the underside of mine looked like that - we are in the rust belt and I have to do this job, ughhhhhhh.

@Ignaciotellez211 14 күн бұрын

What part or valve you replaced?

@GunsNBudder Жыл бұрын

Any idea what the difference is between the tank in the car and the tank in an XT is? Two different part #'s. The STI uses the same tank as the XT, but I'm not sure what the difference is.

@mb01269 10 ай бұрын

Did you ever find difference

@AdamsTubing 3 жыл бұрын

Hello, i have the same problem. would it be possible to hole cut out the trunk above the evaporation connections? and then replace them from trunk?

@ChallengerDood 3 жыл бұрын

I initially wanted to go that route, but would have had to cut through the tube steel that is where the seats bolt to. Would have been much more invasive than just cutting floor sheet metal like I was initially thinking.

@xcosmicspiritx9178 9 ай бұрын

I am in need of your assistance bud. I'm leaking fuel at the yellow elbow at 14:17 is that a separate piece or is it attached to the fuel tank?

@xcosmicspiritx9178 9 ай бұрын

I have pictures and a video unfortunately I can't post it in comments

@AdamsTubing 3 жыл бұрын

also, you didnt show what was wrong. Was it the roll over evap connections or the evap cutoff valve? what needed replacement? many thanks!

@ChallengerDood 3 жыл бұрын

One of the rollover valves had a crack in it where it connects to the rubber hose. I replaced both rollover valves.

@isaacveil4824 Жыл бұрын

any part number for the roll over valve?

@ChallengerDood Жыл бұрын

42084AE170

@jeroddobos4986 3 жыл бұрын

How long did this job take you ?

@ChallengerDood 3 жыл бұрын

About ten hours

@Doofyy11 2 жыл бұрын

Damn that’s a lot of work for just changing the steel fuel neck 😩

@ChallengerDood 2 жыл бұрын

I don’t believe you need to pull the whole tank just to change the fuel neck. You just need to pull the plastic shield underneath it, disconnect the rubber hose from the steel neck, then you can unbolt the neck and pull it up through the filler flap

@Doofyy11 2 жыл бұрын

@@ChallengerDood Thanks alot!!!!