changing oil, changing coolant, and replacing the clutch on a 1g or 2g sv650

Рет қаралды 12,828

3 жыл бұрын

Пікірлер: 84

@0x7FFFFFFFFFFF 3 жыл бұрын

These videos are amazing, there's a lot of knowledge being shared in these, even just little things like the tools used, i.e long funnel and cookie tray, will help me with doing my own servicing. You asked about suggestions, I would personally really like a video on servicing the front suspension!

@Mad8vCycles 3 жыл бұрын

that's a plan. just waiting till i need to do forkseals on something

@Mad8vCycles 3 жыл бұрын

kzfaq.info/get/bejne/mt-KosihrLamf4k.html

@paulj1873 3 ай бұрын

Great video! Going to likely have to replace the clutch on a 2nd gen and this answered all of my questions. Thanks!

@braverabbit 3 жыл бұрын

I really like your videos!! Thanks for taking your time to make them as it has been very helpful, learned to do my clutch watching this video. Also you are very clear, good teacher.

@Mad8vCycles 3 жыл бұрын

I appreciate the kind words. I do know i need to work on some things with speaking (lose the ums for example and stop flubbing sentences!)

@samboles3670 3 жыл бұрын

Dude you're channel rocks!

@TheBluetoo99 Жыл бұрын

Thanks so much. Really helped me. All my questions answered. I measured my old spings - they were significantly shorter than the new ones. I suspect most clutches that seem Ok will be spring issues. My plates looked fine but the clutch was slipping badly. Old gasket was fine too :).

@headbangersvg 7 ай бұрын

Thanks for teaching us :) This video is exactly what i was looking for

@valeriantattoo 3 жыл бұрын

Great video again!

@131601 2 жыл бұрын

Great job, thanks

@matttriestodothings 11 ай бұрын

Currently swapping clutch plates and going a little nuts not finding the round wave washer at 20:08 you're talking about. I'm looking at the 2001 vs. 2005 exploded diagrams, and part 21471-17G00 "SEAT, WAVE WASHER" is not present on the 1st gen. Great vid--thank you.

@Punischar 4 ай бұрын

Torq for the spring bolts are 10nm for de 2nd gen for the 1gen are these 5.5nm

@ploughable 2 ай бұрын

After all, I changed the coolant pump, so I changed also the 2 small o-rings for the pump. Since the coolant left some calcificatioj around it, I had to clean it well before mounting the new ones. The gasket went well, I fitted on the engine. I used 10 Nm for the bolts, but I have small leakage, maybe I will tork the bolts after I will drive the bike for a while

@genarocabrera2869 3 жыл бұрын

Great video and your willingness to being clear with audience, as always. Is it usual that those springs can last several clutch changes?

@Mad8vCycles 3 жыл бұрын

unless proven otherwise there's no reason to replace springs i think? at least i dont

@rileyjacob5463 Жыл бұрын

So I've got coolant in my radiator but not filled to the top, however the tank on the left side has no coolant. So do I just continue to top off until that side is filled up? Not sure if that makes sense and if that's what you were just doing. I'm extremely new to riding and trying to find videos on maintenance. Thanks!

@Mad8vCycles Жыл бұрын

Top the radiator, burp the system, then top off the tank.

@noahgallagher9728 3 жыл бұрын

Do the first gens not have a wave disk spring? My old XJ550 had one just like that but none of my first gens did. 🤔

@Mad8vCycles 3 жыл бұрын

doesnt look like it... diagram on the parts site doesnt have it? www.ronayers.com/oemparts/a/suz/50d411cbf8700230d8b510e0/clutch

@Johnnyreengo 4 ай бұрын

I have this exact same symptom, top of 3rd and 4th seems to slip. I recently installed a new worm gear, could that be the cause if adjusted to tight?

@Mad8vCycles 4 ай бұрын

if it's adjusted wrong, it would slip and wear the plates. but if the plates are worn no amount of adjustment will help

@ralphvalkenhoff2887 2 жыл бұрын

Great video! Thank you Can you swap a single arm rear fork please. I want to do one on my 08.

@Mad8vCycles 2 жыл бұрын

I will not :p cause i dont want that weight

@a_frost. Жыл бұрын

After replacing the clutch plates do you recommend or does the service manual recommend clutch cable adjustment?

@Mad8vCycles Жыл бұрын

Of course. Cause it's now a different stack thickness. It's easy, i have a 5min video for it

@damonmcleod7114 2 жыл бұрын

I need to replace the seals in my water pump, do I need to remove the clutch cover in order to do that?

@Mad8vCycles 2 жыл бұрын

Yep, theres a snapring holding it from behind

@dennisbanks706 2 жыл бұрын

So what would be the torque in ft lbs or inch lbs?

@Mad8vCycles 2 жыл бұрын

No clue off the top of my head. Grab a service manual online (it's everywhere)

@frecciabic28 5 ай бұрын

Hey love your videos they are great! I recently bought my first sv (99) and i rebuild it and now i notice that the clutch sticks. When its warmed up its not so bad and it doesnt stall but every time its cold it does. I will do an oil change now but do you think i might have done something wrong with the clucht? I dont rember seeing the spring disc you talked about in minute 19:52 when i disasembled the clutch and put it back together.

@Mad8vCycles 5 ай бұрын

1g is a little bit different. this was a 2g. try the full clutch adjustment (i have a vid for that somewhere)

@frecciabic28 5 ай бұрын

@@Mad8vCycles thank you. I already adjusted the Freeplay and there is no more play but nonetheless it does not disingage. I can see the pressure plate move away from the plates but they still stick

@Mad8vCycles 5 ай бұрын

@@frecciabic28perhaps the basket is notched and the plates have trouble moving?

@WildWelshBoyz 11 ай бұрын

Why not just swap the complete housing instead of stripping it down to rebuild bro? Just wondering because mine is slipping from 4rpm but I was just going to put the complete clutch from my old engine into my new engine?

@Mad8vCycles 11 ай бұрын

why swap baskets when plates are all it needs? you have to do plates to do the basket, so why do the extra steps?

@ploughable 4 ай бұрын

I 'm having coolant leaks from the pump, did you changed also the o-rings for the pump? Thanks! :)

@Mad8vCycles 4 ай бұрын

I didnt need to. But water pump seals are a common job. Basically the same as what i did in this video plus removing a snapring off the pump gear to get it off

@ploughable 4 ай бұрын

@@Mad8vCycles thanks, I will look into it

@themiddleman7322 6 күн бұрын

What is the torque spec in foot pounds?

@Mad8vCycles 6 күн бұрын

@@themiddleman7322 grab the service manual online. I dont have the useless units memorized

@themiddleman7322 7 күн бұрын

Is draining the coolant needed for a clutch rebuild?

@Mad8vCycles 6 күн бұрын

@@themiddleman7322 on 2g yes. On 1g if youre just doing plates you can do it throught the little cover

@farmoboy83 3 жыл бұрын

how many kms on that clutch? Mine is 60000km and clutch still seems perfect

@Mad8vCycles 3 жыл бұрын

track/racebike... so no idea >< but it had a hard life because of launches etc.

@genarocabrera2869 3 жыл бұрын

For some reference, original clutch in mine is 55 K miles, quite hard urban life with plenty stop lights along the route. Still pulls strong.

@davidgallop484 8 ай бұрын

Why didn’t you fit the basket as you had bought it!

@Mad8vCycles 8 ай бұрын

the clutch basket came out of this bike... it's fitted as it came

@astrojay9782 2 жыл бұрын

Did you add water with water wetter inside that gallon there or is it just water wetter it self? And if so was it distilled water?

@Mad8vCycles 2 жыл бұрын

distilled with water wetter. just wetter by itself is concentrated so it wouldnt be very good.

@astrojay9782 2 жыл бұрын

@@Mad8vCycles thank you so much man you are so reliable! Keep it up🙌 I have one more question... About the 2 rings in the clutch, I think you said something about a spring ring goes first and the one that's a straight spring goes second?

@Mad8vCycles 2 жыл бұрын

@@astrojay9782 i think i made a mess of that. but there are 2 round things behind the plates. one is basically a washer and the other is a spring (it's like a dished washer). i for the life of me can never remember which way it's supposed to face.

@astrojay9782 2 жыл бұрын

@@Mad8vCycles did you run into any issues after?

@Mad8vCycles 2 жыл бұрын

Not really. Either i got the orientation right, or the spring plate doesnt matter that much

@urgranny6913 2 жыл бұрын

Great video, I would add you should also put oil in the oil filter so there isn’t a dry spot and you should soak your gasket in oil too for a better seal and it will also keep it in place

@Mad8vCycles 2 жыл бұрын

I always do the wipe the oring w oil on the filter (or did you mean the side cover gasket?). Never really bothered prefilling it since i just top off after running the bike.

@urgranny6913 2 жыл бұрын

@@Mad8vCycles both, just like the o-ring, wetting the gasket will also help with a better seal. And I’ve always prefilled my oil filters so the cams get oil immediately after cranking the bike and there isn’t a dry spot.

@Mad8vCycles 2 жыл бұрын

I like the gasket idea. Will try it next time something is getting opened up again

@jimsnow8004 Жыл бұрын

Some say don't prefill the filter because that (admittedly small) volume of oil goes through the engine unfiltered on startup. Others say the few seconds of low oil volume while the filter charges causes more damage than the potential crap in unfiltered oil. Take your pick....

@urgranny6913 Жыл бұрын

@@jimsnow8004 I’m sorry but that makes no sense, for one, it’s fresh oil so I doesn’t need to be filtered. And two, none of the oil you are pouring in your engine is filtered 😂, maybe I’m not understanding what you’re saying

@seyedmohsenmirmobini591 2 жыл бұрын

Thank you for the video, I just changed my dl650 clutch which has a similar engine to your sv650. But even after I changed the clutch it slipps even worse do you have any suggestions

@Mad8vCycles 2 жыл бұрын

Do the full adjustment procedure? Using a jaso ma or ma2 oil?

@seyedmohsenmirmobini591 2 жыл бұрын

@@Mad8vCycles I did the adjustment and I took it for a ride after 20 min, it was slipping so bad that it wouldn’t go more 20 mph. I made sure the clutch was not engage. I used Super tech 10w40 full synthetic and new oil filter

@Mad8vCycles 2 жыл бұрын

Is it a car oil or a bike oil?

@Mad8vCycles 2 жыл бұрын

Also when you replaced it, was it oem plates or something else? Did the stack thickness change?

@seyedmohsenmirmobini591 2 жыл бұрын

@@Mad8vCycles it’s motorcycle oil 10w-40 motorcycle full synthetic