How to change brake shoes and drums on a semi tractor. Was at the dot legal limit on my rear axle. Went ahead and did both axles.
Пікірлер: 30
@japspeceg7 Жыл бұрын
Catch the center spring first between the drums, install on the hub and then Catch the two small side springs last with a vice grip and a bar.
@CruzTube Жыл бұрын
10-4! I’ll give that way a shot the next time I do them
@kevincooley5201 Жыл бұрын
Put the old shoes up against the new shoes and you'll see that they were only about halfway worn out now that I look at the new one you didn't need to change them
@towikameha76167 ай бұрын
What helps a lot for me is leaving out one of the silver rollers by the two small springs. It closes the gap to more easily install the center spring. Then I run back with a pry bar, pry back and install the other roller then do the last two with the clips at the center spring. Just my 2¢ if you're ever struggling with prying up on the center spring. 8:10
@towikameha76167 ай бұрын
There are also spring installer tools for those two back springs. It grabs the springs and stretches it. One of my buddies has one. Made installing a lot faster.
@CruzTube7 ай бұрын
@@towikameha7616 10-4. Thanks for the tip man. I really appreciate it. Next go around on a brake job I’ll give this comment a visit
@RanjitSingh-ph2oyАй бұрын
Can’t see clearly
@kevincooley5201 Жыл бұрын
Those brake shoes still had at least another 10 20,000 miles left on them
@CruzTube Жыл бұрын
Yes I agree, they were on the first axle. The second axle were at the DOT minimum. I should have shown those instead. I just went ahead and did all of them at the same time so I’m good from here on and don’t have to worry about doing them later down the line
@demetriosanchez7451 Жыл бұрын
You from Arlington
@CruzTube Жыл бұрын
Yesssir
@demetriosanchez7451 Жыл бұрын
Right on how’s Oakley treating you? They keeping you busy.
@CruzTube Жыл бұрын
@@demetriosanchez7451 you from Arlington too? They treat me pretty good man. I’ve noticed this year it’s slowed down. Instead of having a load waiting for me when I empty out, I’m having to wait a while till I get my next dispatch. But they keeping moving and I’m still making money. Once spring rolls around I’m guessing we will be balls to the wall again.
@demetriosanchez7451 Жыл бұрын
Yes sir but I’ve been living in Southwest Kansas since 2016 been trying to move back but I’ve been on the road try to make this paper and on my downtime you know watch a little KZfaq ran into yours just reaching out to say what’s up keep the good videos coming in c’mon
@CruzTube Жыл бұрын
@@demetriosanchez7451 that’s what’s up man. I can have someone from Oakley contact you and give you some info if you’re interested in coming over?
@glackaglack15345 ай бұрын
How many miles was on the truck
@CruzTube5 ай бұрын
Brother I can’t remember to be honest at that time. I would guess around 350k
@GarySmith-dg1sj4 ай бұрын
You guys are terrible you didn’t do an explanation what the heck you’re doing and each step somebody’s watching your video how do you release the break underneath there with that socket wrench
@CruzTube4 ай бұрын
@@GarySmith-dg1sj it’s not a how to video. Just recording day to day trucking content and what it consist of. Thanks for your feedback either way. This was when I first started recording and being an owner operator. I’ve gotten better at explanations since than.
@kevincooley5201 Жыл бұрын
You're doing it the hard way is all you need is a train to put that Center spring on