Changing the Transmission Fluid and Filter on a TH350 Transmission

Рет қаралды 25,592

2 жыл бұрын

The transmission pan gasket was leaking and the transmission fluid on the dipstick looked suspect, so we're changing the filter and the fluid in the 1986 C10
Kudos to the Car Wizard for tips on making things easier: / carwizard
parts used:
Mobil 1 112980 Synthetic Automatic Transmission Fluid
amzn.to/3xIgJhd
AC Delco TH350 Transmission Filter and pan gasket kit amzn.to/3n62qhA

Пікірлер: 32

@ArrowheadGarage 2 жыл бұрын

Getting ready to do this on my FIrebird, thanks for the video... them them coming!!!

@thejustmechannel3298 Жыл бұрын

🎉🎉🎉 thanks so much keep it up. 💯

@MarkBallinger-cd4xm 6 ай бұрын

Good video. Thanks

@jimmycarter9099 Жыл бұрын

Remind me of the nova trans 1974 😊

@rustynutz7158 Жыл бұрын

Clothespins are great for holding it in place while positioning it ... actually clothespins and paint sticks to keep it flat

@OldGrumpsGarage Жыл бұрын

good tip!

@jamesfoster4555 10 ай бұрын

Reading some comments. People can be such jackasses. Good job, this is what I needed. Thank you sir.

@OldGrumpsGarage 10 ай бұрын

Thank you for your kind words

@Outrunninaround. Жыл бұрын

Ty, gotta do this on 69 chevelle.

@Xix305 2 жыл бұрын

Awesome video sir , I had a question how many quarts of oil did you end up using? Only 4 ? Or more after it got to the right temperature to check the level

@OldGrumpsGarage 2 жыл бұрын

Thank you. I ended up using 4 quarts. Once warm I checked it twice and it showed full on the dipstick.

@Xix305 2 жыл бұрын

@@OldGrumpsGarage awesome , thank you for the info boss , I’ll sub your channel

@gjjcgmail9930 11 ай бұрын

Great video. 1) Any leaks so far? 2) cork better than rubber gasket? Thanks!

@OldGrumpsGarage 11 ай бұрын

None. She's dry as a bone. No more puddles on the driveway.

@Camopar87 10 ай бұрын

I had to do the same thing with the pan on my 13 Charger. No drain plug on it either

@ianharvego8978 Жыл бұрын

I'm trying to remove the pan on my 71 c10. I've run i to a problem with the last 2 bolts are completely blocked by the crossmember supporting the transmission. Is there a right and or wrong way of getting to those bolts?

@OldGrumpsGarage Жыл бұрын

loosen or remove the bolts where the transmission mount bolts to the cross member, put a jack under the tailhousing of the transmission and lift a coupe inches

@waynepierce7305 10 ай бұрын

Thanks a lot.. I was stressing this.

@wchodson 3 ай бұрын

But how did you get the pan off? I have all bolts off, but pan will not come out, there is a bar over one side, 72 Cutlass

@OldGrumpsGarage 3 ай бұрын

Are you talking about the transmission crossmember? If so, take the bolt out of the transmission mount and gently jack up the tailshaft of the transmission just enough to slide the pan out

@markmelendez1029 Жыл бұрын

I don't recommend the super glue tip. Big headache on the next gasket replacement.

@ET74019 Жыл бұрын

Not really when he replaces filter it will go with the old filter

@gabrielrivera4929 Жыл бұрын

Yes and no. If you end up changing the gasket there’s no way you could save the gasket but I’m sure if u took a blade to it, it would come right with some elbow grease.

@OldGrumpsGarage Жыл бұрын

comes right off with the lil blue scotch pad ;)

@bobbyeddins1132 Жыл бұрын

I usually use sewing thread to tie my gasket in place using every other hole and a small wire wheel on a cordless drill to clean my pan surface.

@MarkLoganFIB 2 ай бұрын

@@bobbyeddins1132 use the bolts and attach them from the top, when you go to reinstall it remove the bolts and insert them bottom side. You don't need every bolt on the bottom to keep it in place enough to install it so just put as many bottom side as you can handle, the start ratcheting them in. With smart placement you can just slip the other ones in because the other holes will be aligned enough everything just fits.

@carllattimore8227 Жыл бұрын

How many Quarts?

@forceescape3335 18 күн бұрын

@frankjetson877 11 ай бұрын

you don't really know what you're doing. used a screen for a filter and not using a 1/4 drive torque wrench on the pan bolts .

@OldGrumpsGarage 11 ай бұрын

Thanks for watching a d commenting. Be sure to like, subscribe, and click that lil bell 🔔 icon so you can be notified when we post more content. Have yourself a great day!