*✅ Tools HERE* 👉👉 https:movilone.eu

Warning (which should have been verbalized): Before removing the screen, go to the end of screen removal in the video where you can see the back of the display. Note that there are flex circuits stuck to the back of the screen. There is a large one at the top with a large connector that goes out to the side and there is a skinny flex circuit that runs from the center (button) up about 2 inches. You cannot shove a card in deep in any of these areas or you will rip the delicate flex boards, especially the large on at the top. Note that in the video, they work from the bottom (side not absolute bottom) and pry the screen off from the bottom so that by the time you get to the delicate large circuits at the top, you may not need to use the cards or pics to break the glue. You might be able to just pry it apart at that point, avoiding hitting that circuitry. You might have to reheat the are repeatedly, front and back, to get the glue to let go easy enough so that you do not break the screen trying to pry it open. But back at the bottom where you start, you need to also be careful to not go too deep with the cards. You are safe in the area where they show you start... working a card under that metal frame. That area has no flex circuits. but that is the only area that has no flex circuits. In all other areas you can only go in shallow with a card or pic, if at all. With all that in mind, maybe make a little sketch of how that display looks from the back, and use that sketch for your strategy. And re-watch this part of the video (screen removal) with all that familiarity now. Now the details of penetration etc will make more sense. Doing this a second time would not be so hard, but on first try, you will probably destroy the flex circuits unless you pause when it is time to remove the screen, and accept that you are not close to done yet. You will have to take some time and strategize and watch that part of the video more than once. I gave the video a like, but then a dislike when I finally finished and had destroyed my flex circuits glued to the screen. There should have been emphasis / a caution about this. YOU DO NEED A HEAT GUN, though I have seen other videos where they use some kind of solvent to weaken the glue. I think the solvent was called "KONTACT PCC". They bleed the solvent into the cracks, and then add more solvent once there is a wider crack. You should look for that video if that is going to be your tactic. But this heat gun method almost worked for me.

I think you're the only one I've seen come through the back like that what a great idea!

Dude I don't know why this vid doesn't have more views. Awesome job!!! Over vids say you can't replace USB port without breaking screen. Thanks you really made my weekend!

And all this time i thought it's impossible to disassemble the screen without cracking it Great job man,i learned a lot!

lol ok i need to just buy a new phone

Thank you so much! Now i can repair my own phone. Question though, why did you have to use a heat gun at 15:30?

Sir I have no words to give complement to this amazing work. Hats off.

This is the best step by step breakdown of a s7 egde, wonderful video bro.

Amazing guy, very patient & resilient! But, no, thanks, I will pass. I can still charge and use my phone by taping the cord's end (to take the free movement/slack away) just after being inserted into the port. Yes it is non-sense laborious to do that but what you have gone thru to change the port is a complete removal of all components from the casing. Ayayaya, this is crazy... should be avoided at any cost.

This work is very difficult for beginners. .. Thank you

Many thanks for your great video, which glue do you use please?

Amazing job!! I am about to attempt this now..... Hopefully I can be as good as you

Good job, but it's much easier to replace just the charging port, not the entire dock connector. You save a lot of time and avoid the risk of braking the LCD.

You are too good at explaining others get lost in the dialogue instead of teaching. You are very good!

thanks ,your video is very helpful, which type of Glue do you use? my S7 Edge does not work because of water, how can I be sure which one of these is damaged/ charging port, Battery or main board , I mean to test??? thanks anyway

Hello great work please do I need to replace the screen while changing the charging port..thnk

You have crazy skills to remove the screen without breaking it! Are you able to do that consistently? If so, do you want to look into repairing the pink line issue? I believe all you need to do is once the screen remove, put adhesive or tape onto the Display's ribbon cable and the pink line will be gone.

You guys deserve a complete Like.. There you go (y)

Awesome work man! One question, does the glue you added (B7000) makes the phone waterproof again?

Much thanks ! You guys are wonderful. ...

I recently replaced my s7 edge screen and audio jack, but the audio jack is still unresponsive. When I plug headphones(they're not faulty headphones) in, the sound comes out of the phone speaker. Could this be a problem with the charging port part? Also the "recent button" is also non responsive. It was working before, but I might have damaged it. There are no cracks or tears that i have noticed.

Uffffff que laburo viejo te felicito por la prolijidad 👌

excellent video

Thank you! You made this easy peasy.

Great video, nice and close to view. The battery removal with the playing card was great. Others tend to pry it up with tools. Cheers

, how much do they usually charge to have that fixed I'm currently having this problem and only can use the wireless charger and it sucks cuz it's kind of slow even if it's a fast wireless charger

Really good job

ótimo vídeo,parabéns!!! qual o nome das colas que você utilizou?

That is impressive, but so much work. I think I'll just live with mine and use some tape to hold the cable in the port just right until I can buy a S9.

You must remove screen also?? Wust be way better to use soldering instead of stressing the screen and maby waterproofing even more.

Outstanding video!

Its not needed to remove the old glue before regluing back in place?

All them ribbons 😮 I'd for sure bend a pin trying to snap it back on

Thank you bro very nice

I wayched all the video because I want to know what makes the cellphone water proof, I got one I scare about get it into the water but at the same time I want to do it because i had a s5 and I remember I got it into water and was awesome, can you help me with any answer or something?

This is such a challenge to get done but i will try it just please tell me can i use a hairdrieer to remove the back plate and the screen

I lost one of the two screws holding the usb port... My buttons came without adhesive on...

What's the temperature are you applying? 60 C or 100 C for back cover removal? and for the Lcd ? Thanx in advance

What is the yellow glue he is using .. Or is a cleaner

Great work !

Nice vid, but I have one concern....you did show if it was charging after it was all put together. I could see that there was no indication that it was "charging". I stopped the vid at 21:10 and there was no "charging" indicator on the battery indicator. So, this doesn't show if you repaired the issue with the charging port or not....just saying....

Super

i noticed u were using 2 different types of adhesive on the front and black glass what kind of adhesive is that?

They didn’t mention this in the video, but I want you guys to be careful when taking off the screen and going through the adhesive, don’t poke too far in near the lock button because that’s where the cable for the LCD is and it’s very sensitive, i accidentally ripped mine because I didn’t pay attention to how close the cable was to the edge. Not blaming the video maker, it was my mistake, just don’t want anybody else to make it and have to spend $150 for a new LCD

This video is a Full Disassembly; there are several other videos that do not remove as many components and take less time.

Nice

What glue are you using?

hey what is the white and blue cable one of them is broken in my edge, first day there was no connection problem but next day i have lost network connection. is it antena, if it is why it is two item.

awesome...nice Job.

Will this fix "USB device not recognized" in Windows 10? I installed the Samsung drivers and am using a Samsung cable already.

great work

Amazing...

Great bro

Good job

Could this repair be done without the glue just heat?

Is is the phone still waterproof?

Is there one with a usbc port out there?

This is righteous, dude. You're a pro

The screen removal almost seem impossible,but I will be careful with my track pad next time, because I just cut mine.

Can you please make a video to how solve the pink line problem in s7 edge

Hi... does the fast charging work again?

Sir I have Sam s7 edge for which normal charging is working, but fast charging and USB connection is not working, I've also checked with another device for which fast charging is working with same cables

What are the bits that curl around to the front glass? Do we really need them? ✂️✂️✂️

Type of glue?

Does anybody know where can i find the just the black plastic that cover the back and menu bottom that goes on the lower part of the screen?

Adhesive?

what is the name of the Glue you are using?

Charge port had attach touch buttons left write as well????

You missed some parts with glue.

ta vidéo est tro bien sil-teplai refais une votre vidéo sil-teplai

GOOD

Why fast charge in video not work ??

I need to do this to my s7

Bro without removing screen can we change it

Sir mai v apna s7 edge ka charging port change krwana chah rha hu bt koi nhi kr pa rha h

👍👍

Hi

i have replaced so many screens and ports over the years. I told my friend I would fix her port and this scared the sh*t out of me. Damn it this is going to suck balls.

What is the price of this charging port

Damn, the stuff that happens around 11:20 is pretty crucial. Just broke my S7 screen into 100 pieces, phone goes in the trash. Wish I knew where in your channel the video without removing screen was before following this guide. Can't find it. Oh well, have to use a new phone instead!

My S7 edge won't charge with any cable or adapter. Is the USB port the problem?

How do I fix the usp port on it my son's bottle spilt on it and now it won't charge

It pays to replace a Galaxy 7 socket today

Sir

Pop

Hii

No wonder these cell phone repair places charge so much money. Look at all the components you have to remove and put back.

holy shit thatts too much. my phone's charging port does not work so i was thinking of replacing it but after seeing this video , nooo man. no. im good with wireless charging

Братан нагрей Арарат нормально не мучяйся у меня чуть енфарт не случился

Why is it so difficult to do? Why do you need nifty fingers? I can't do this otherwise I'll break something

Les ingénieurs Samsung ne sont pas compatissant, ils auraient pu nous faciliter ! Ca aurait été plus commode pour nous "les Clients". Autant changer de téléphone

They really don't want you to take apart these phones do they. Honestly,my patience would probably run out and I would smash the phone into a million pieces.

Tools :1deck of cards lol.

Tried it, turned the phone back on and the LCD's ruined. $350 for a new one, the same price as a new phone lol

Agar aap kr denge change to visit kr sakta hu aapse apna contact no. De

I do not have the patience or will ti do all that. I will just buy a new phone. Im 65 now and i'm lazy . Ha ha😊

Kids... Don't try this at home. 😵😵‍💫😱

cringe. u don't need to use force so much if you use the heatgun more. u likely damage the parts with the way your removing them

Please remove the baterry flex firsly you can't work like that please do a better job you can't desconnect de lcd flex wen the battery is still connected