Chasing my own Tail(stock)

Рет қаралды 304,043

Күн бұрын

Thank you Incogni for sponsoring this video! Take your personal data back with Incogni! Use code INHERITANCE at the link below and get 60% off an annual plan: incogni.com/INHERITANCE
The lathe has been glaring at me for 4 months, it’s time to put it to work. And by "it", I mean me.Which, as you might expect, never goes quickly. And while I can’t promise a super satisfying reveal, can I tempt you with a negative side project total? Who would have believed it?!
#inheritancemachining #machineshop #hobbymachinist
Patreon - / inheritancemachining
Drawings Store - inheritancemachining.com/?pro...
Merch - inheritance-machining.mysprea...
Instagram - / inheritancemachining
Amazon Store (affiliate) - www.amazon.com/shop/inheritan...
Thank you again to the Micrometer level Patreon members listed at the end of the video!
TIMESTAMPS
0:00 Intro
0:55 Two Is Better Than Zero
2:04 Simple is... Boring
3:37 I Overthunkit
6:18 A Little Over Dressed
8:22 sniff sniff
10:08 Spring Break, Baby!
11:33 What's that tickin' Noise?
12:52 Gettin' Smok'd
14:56 Hyperbolic, Dontchathink?
16:58 Rookie Mistake
18:27 Indecent EXPOsure
19:45 Hot Date
FAQ
Drafting Equipment (affiliate links): amzn.to/3P0HvMe
A/V Equipment (affiliate links): amzn.to/3Pi45jB
Editing: Final Cut Pro X
Intro Song: Way Back Way Back When (Instrumental Version) - Gamma Skies
www.epidemicsound.com/track/S...\
This video was sponsored by Incogni.
• Chasing my own Tail(st...
© 2024 Inheritance Machining, LLC. All Rights Reserved.

Пікірлер: 652

@InheritanceMachining Ай бұрын

Thank you Incogni for sponsoring this video! Take your personal data back with Incogni! Use code INHERITANCE at the link below and get 60% off an annual plan: incogni.com/INHERITANCE Also, I apologize in advance for how loud the phone ringing is in the video. Probably should have given this a listen with headphones before uploading 🤦‍♂ Please excuse my negligence!

@badasson8825 Ай бұрын

That’s some smart advertising ngl. Those scam calls really put me off and right in the middle of my therapeutic machining video session of the week! Bold!

@nikkiofthevalley Ай бұрын

As an electrical engineer, your handling of that motor caused me significant distress..

@drinkmorecocacola Ай бұрын

LATHE MODDING? *creams*

@ivarsande3746 Ай бұрын

Great video as always! Filming, project, humor, narration; all of it. I laugh and I learn. Was that Paul Sellers I saw sawing (pun intended)?

@jaysuthar8749 Ай бұрын

If you don't keep paying them then incogni can just sell your data back to the scammer now it is a 2 way business

@dimitar4y Ай бұрын

Curse that generous patreon dude that gave you a spindle! He deprived us of an entire side project video! D:

@Critter145 Ай бұрын

🤣💯

@wompastompa3692 Ай бұрын

I'm just counting everything about the second lathe as a side project.

@HappilyHomicidalHooligan Ай бұрын

Relax... There WILL be more Side Projects... Be patient Padawan... 😄😁😆😅😂🤣

@brettfontaine4681 Ай бұрын

@@wompastompa3692 inception!

@cezarysawicki4541 Ай бұрын

Shame on him!

@gdude2775 Ай бұрын

I love how with the community giving parts and such he is in a way continualy inheriting machines.

@duodot Ай бұрын

The Constant Grinder

@douglascodes Ай бұрын

The real adventure was the machines we inherited along the way.

@noxious89123 22 күн бұрын

Inheriting tools and machines to help him restore the other tools and machines he's inherited and going to inherit.

@leftistagitprop Ай бұрын

I love your content; I have cerebral palsy, so I'm unable to work, but it's so relaxing to watch. I love your dry humor.

@drinkmorecocacola Ай бұрын

wtf is my excuse to watch these without doing any shop work...

@ponyboyjl13 Ай бұрын

@@drinkmorecocacoladon’t compare your struggles to anyone else’s. We all have our own shit. You have yours and I have mine.

@Manufacturingsite1 Ай бұрын

Amazing videos

@unironicaluser1867 Ай бұрын

dude what he was making a joke@@ponyboyjl13

@bluecraney1 Ай бұрын

If you think his humor is dry add a little “magic sauce”

@joshholmberg2346 Ай бұрын

Smash cutting the video because you have a date with your wife that’s more important is so sweet. My new favorite outro ever

@InheritanceMachining Ай бұрын

Priorities!

@deamonengineer6107 Ай бұрын

@@InheritanceMachining should of made the new live centre increase the side projects after that call though

@user-ru3im9rd6b Ай бұрын

He was enthusiastic about the date. I'm guessing she asked him to taker her to a tooling store to shop for live centers and other tool centric paraphernalia.

@mooreevair Ай бұрын

@@user-ru3im9rd6b man's gotta bore what a man's gotta bore

@Koushakur 24 күн бұрын

@@user-ru3im9rd6b To a store that sells heat treatment ovens more like it

@bogeyoffear Ай бұрын

"... gave up the ghost" :D As a german I can confirm: That spring definitely gave up the ghost.

@RNMSC Ай бұрын

As did it's first replacement. I wonder if the earlier clean up work pulled the conductor off the contact, and that's why the first spring opened up. (It was designed to hold the contact in place, not carry the load.)

@duodot Ай бұрын

Die shpringy shproingy hast die geist aufgeben.

@TheMilfMoncher Ай бұрын

I thought springy sploingy was literally the German name for a spring lmaoo. It’s so on brand 😂😂

@janoschk.5730 Ай бұрын

@@TheMilfMoncher But then you looked it up and found out that spring actually means Feder in German?

@tngdwn8350 Ай бұрын

Is "gave up the ghost" actually a common saying in english?

@dedede9664 Ай бұрын

"one restless sleep of lucid dreams later, I think I know what's going on" I feel like these are the words of inventors of the past, those great men whose inventions and discoveries changed the way we live

@7LegSpiders Ай бұрын

I watch this channel at normal speed on a big screen, never sped up and never on my little phone. Some content deserves that, and I deserve to treat myself to good content in that way.

@InheritanceMachining Ай бұрын

wow, thank you! 🙏

@trillogy998 Ай бұрын

And i watch his videos in VR for that ultimate experience

@ardesignsrc Ай бұрын

The fact that you can rebuild that motor simply and efficiently is the reason why old stuff is so cool. It's like the creators designed it this way. Anyone with some mechanical knowledge can repair it. Not like the trash created today

@Q.7 Ай бұрын

I wholeheartedly agree with this comment.

@mvadu Ай бұрын

That's why right to repair should the norm everywhere!

@dimitar4y Ай бұрын

this comment exactly describes the bane of my existence, ESPECIALLY WITH CARS. Repairing anything on them is prohibitively expensive due to the parts being artificially overpriced, and needing the engine block to be taken out and stripped almost completely.

@spdcrzy Ай бұрын

I was JUST about to say this! It's SO nice that it was obviously designed with self-repairability and longevity in mind. Not like shit today. It could be! That's not an issue! But it's not.

@zyeborm Ай бұрын

I don't think it was "designed to be repairable" as such. It's mostly the cheapest way of assembling things at that quantity at the time.

@Particleking Ай бұрын

PSA: I realize the fake spam calls were just joke segues, but a reminder for anyone watching that you DO NOT want to decline spam calls, you should let them finish ringing. Muting them is also fine. By ending the incoming call you are confirming that they reached a live person. Ending calls early can lead to being prioritized for more spam calls.

@dMb1869 Ай бұрын

This comment should be pinned.

@TheStealthbob 25 күн бұрын

Truth

@EnricoMarangonJunior Ай бұрын

It is a real delight to see you care and refurbish all the amazing equipment, the tools, your Inheritance. With your knoledge and skill. Thank you. You honnor the Machining way of thinking.

@InheritanceMachining Ай бұрын

Thank you for being here as well!

@stevespra1 Ай бұрын

I love the way you show your love for your wife. Too many of us complain about our wives constantly, taking for granted how truly blessed we are to have them. And especially that they will have us. Oh, and nice machining content, too!

@amazeddude1780 Ай бұрын

That box of springs will be just the ticket for your spring cleaning project.

@InheritanceMachining Ай бұрын

niiiiice

@TrailerTrashBuddah Ай бұрын

When the grinder started up 7:48 all i heard was R2D2 screaming 😂

@InheritanceMachining Ай бұрын

😆

@britneyfreek Ай бұрын

the pitch kept going up. i was waiting for it to blow up.

@KingCobra459 Ай бұрын

There's no way you only replaced the one of those two springs bindings 😆Fair play wanting to get back to the main project but... c'mon hahaha

@nordishkiel5985 Ай бұрын

Just my thought. it will never be as easy to do the other one. It´s just as old...

@beerdygeek Ай бұрын

My thoughts exactly. You already have it open and cleaned up with the new pieces ready to go. Just do both and give yourself peace of mind.

@InheritanceMachining Ай бұрын

Somehow it literally never occurred to me to do both until now 😆

@KingCobra459 Ай бұрын

@@InheritanceMachining 😅 I know you would have because I can picture your voice from other videos saying "And while I'm here... may aswell give this other connection the same treatment" but I was giving the video the old side eye in those moments haha

@KryptLynx Ай бұрын

@@InheritanceMachining Now you will suffer until you replace the second one :D

@RedDogForge Ай бұрын

my heart was in my throat for you during the whole malfunctioning grinder incident..i love my dumore ( ive got the lil brother to yours ) and while theyre built like tanks electricky has always mystified me ..i was like " oh no NOT THE SMOKE??!"

@InheritanceMachining Ай бұрын

😂 i was literally thinking, man... everyhting is going so smoothly. Then POOF! all that wen't to hell!

@hidef9265 Ай бұрын

I love it when things are simplified to "settling on the happy only ground". 😂

@AlexMusayev Ай бұрын

"Dressing the wheel" moment was brilliant 🤣

@ElectroTree01 Ай бұрын

Even though I’m not a machinist, I enjoy your videos and definitely get something from them.

@julianholcroft9625 Ай бұрын

I love the spring box I work in a multi generation precision machine shop and we have a spring drawer just like that in our tool room.

@InheritanceMachining Ай бұрын

they key is to have them all in one place haha

@intellectualiconoclasm3264 Ай бұрын

Well, today just became even better.

@JohnChuprun Ай бұрын

I think the spring is the main electrical connection in most of these designs, it was in the drill I refurbished that is a universal motor like this one. I think it just needed a larger diameter spring to support the inrush current, but of course soldering it directly is even better!

@LaxianKey1 Ай бұрын

The best 21minutes and 51 seconds of my Friday morning (Cutting Edge Engineering is 31:32) :)

@izsaf Ай бұрын

Wanted to throw out a minor tip: though it probably doesn't matter too much given the size here, it's generally bad practice to blow on solder joints. It causes it to cool faster and therefore become more brittle and prone to failure in the future.

@D3nn1s Ай бұрын

Thanks, i didnt know that! I usually do it when solding small things because im quite bad at soldering and dont want the rest of the board to overheat :P

@thegoodlookinorange1986 Ай бұрын

Yeah ya jinxed it. Can’t get away without at least 5 side projects. 👍👍❤️

@TobaccoTooling Ай бұрын

Hell yeah! Been waiting for more content on this beautiful lathe 🔥

@Lamefoureyes Ай бұрын

*How are they such a cute couple even when it's only one of them in the video???*

@G89- Ай бұрын

4 month already :o times flies past so fast Was looking forward to another restoration video/ episode :D

@InheritanceMachining Ай бұрын

You're telling me! 😂

@andyspillum3588 Ай бұрын

I am having SO much fun living vicariously through you, imagining I have even a fraction of your tools. And watching you build stuff is cool too, I guess (that last part was sarcasm). The best part is watching you actually get the stuff you take apart back together working

@rupunzel6299 Ай бұрын

Keep this in mind as you're working on this Hardinge HLV-xx clone. These lathes have a dove tail bed with the power feed on carriage. This means as the power feed runs the carriage across the dove tail bed the forces will be applied at an angle to the carriage moving on the dove tail bed causing the corners of the carriage to wear in a "crabbing" pattern. Other issues to be aware of, wear pads under the carriage/tail stock. The Hardinge HLV-xx lathes have become a "desirable" lathe in the same way as the Monarch EE, yet there are designed in problems with these lathes users/owners need to be aware of.

@evannewman3997 Ай бұрын

Wow, I hope he sees your comment.

@mantis0427 Ай бұрын

Your videos just make my fridays. Or at least every other Friday! Keep up the good work 🎉

@DavidSmith-jc4yk Ай бұрын

Hey awesome! You installed your outlets the correct way...ground prong up!

@alanmckinnon6791 Ай бұрын

See that light switch inline with the power cord to the motor? That's your problem right there Brandon! Horrible things, hate them

@dimitar4y Ай бұрын

Having replaced a fair few of those on the older lamps, I too feel that pain. Don't know how they make them so poorly.

@pingwuan_works Ай бұрын

The lathe is just sitting there....MEANCINGLY lel

@intellectualiconoclasm3264 Ай бұрын

Tools you can work on are THE BEST!

@neilward9932 Ай бұрын

Was going to comment about you not cleaning up the commutator when the motor was stripped, but I see that you eventually did, before the final assembly. Cheers

@FunctionalPrintFriday Ай бұрын

I know the lathe spindle wasn't on when you put the towels there, but try aluminum foil instead. You can crumple it up with the waste in it when done, and if you DO turn the spindle on, things are a lot less dramatic if the spindle grabs the foil. It just tears rather than turning into spinning death. EDIT: you did turn the lathe spindle on with the towels there :P

@dimitar4y Ай бұрын

but the foil gives nasty papercuts :c

@user-ym4xy6us5e Ай бұрын

@@dimitar4yWhat the hell kind of foil do you buy?

@dimitar4y Ай бұрын

@@user-ym4xy6us5e all the foils cut ;(

@VenTGM09 Ай бұрын

i swear if i see people complete the video without skipping when it's LITERALLY 19 MINUTES SINCE IT'S BEEN POSTED

@dekutree64 Ай бұрын

Some of us watch at 2x speed.

@fakename287 Ай бұрын

@@dekutree64 damn, tiktok is really burning out the kids' brains these days, isn't it?

@VenTGM09 Ай бұрын

@@dekutree64 speedrunning

@_Jester_ Ай бұрын

@@dekutree64 Why on earth would anyone want THAT? No attention span for 21 minutes?

@dekutree64 Ай бұрын

@@_Jester_ Gain twice as much information in those 21 minutes. It may not seem like much, but if you watch a 21 minute video every day for a year, that's 64 hours of time saved to do more important things.

@copescale9599 Ай бұрын

The box of shame is adorable I always knew he would be a good character!

@dimitar4y Ай бұрын

it even went

@APOC1385 Ай бұрын

I would recommend a side project. You should make a guard for the tool post grinder's belt. Not that lathes are safe in the first place but seems like a non obtrusive way to CYA

@Testingturbo Ай бұрын

It's so nice to see what you make in your manual machines. Im so impressed. I love your videos and the precision you are able to do there. Thank you.

@NoEngineerHere Ай бұрын

In awe of the box of shame's role in this one. Raw talent.

@cristinelcostachescu9585 Ай бұрын

Wait, what? Negative side-projects count now? Amazing!

@InheritanceMachining Ай бұрын

When you make the rules, anything goes!

@robinisthereason Ай бұрын

Not only an Inheritance Machining video, but one about grinding? As a manufacturer of high precision CNC bore (among other applications) grinding machines, I loved watching this. Not what our bore grinders do, but still the same as what my bore grinders do, if you get what I mean. There's just something special about doing it "by hand". And if you like the surface finish, I wish I could show you around the metrology lab over here. 😁

@jmiddlefinger Ай бұрын

Always great stuff, Brandon. It’s been awesome watching your channel grow!

@vis7139 Ай бұрын

It's so clear that you put as much time and effort into your videos as you do into machining. I'm fairly new to this channel, and the more I watch, the more I can see how much precision goes into every element of these videos. You've got a subscriber in me xox

@chrisb8783 Ай бұрын

Loved it! Thank you.

@vaultboy2270 Ай бұрын

Absolutely love the content. Please keep it coming!

@InheritanceMachining Ай бұрын

Thanks!

@florisberents8971 Ай бұрын

I randomly stumbled on of your videos one day. And now i watch every single one your videos. There just so satisfying and calming.

@stevelamperta865 Ай бұрын

I just wanted to thank you for taking the time to make these videos ! I have a small machine shop and just started machining 4 years ago. Ive learned a lot from your videos ,..thank you.

@InheritanceMachining Ай бұрын

My pleasure! Thanks for being here. Happy machining!

@ThatcraniumguyNet Ай бұрын

Seeing you lean over the grinder with the belt running gave me goosebumps. I would recommend fabricating a belt cover for that thing if you don't want your shirt getting sucked into it.

@Ben_R4mZ Ай бұрын

The button is the cherry on top of this channel. Always there to punctuate a satisfying moment.

@Kris_at_WhiteOaksFarm Ай бұрын

Love your gentle humor, voice and clear explanation of mistakes and fixes. I don't have machining machines, but the thought process is worth the watch and education. Thanks!

@InheritanceMachining Ай бұрын

Glad you enjoyed it! Thanks!

@mumblbeebee6546 Ай бұрын

Nice of you, Mike!

@garychaiken808 Ай бұрын

Great job. Thank you 😊

@williamgrizzle8480 Ай бұрын

Your ad reads are freaking fantastic.

@charlespetitjean3961 Ай бұрын

Now THAT is a pleasant surprise on a Friday afternoon! Thank you for the awesome content!

@InheritanceMachining Ай бұрын

My pleasure! Thanks!

@ragnoon Ай бұрын

awww yeah, I love it when a new video comes out

@benruniko Ай бұрын

Wow those springs in the motor were holding on by a THREAD! Also wow convenient you had that replacement just hanging around lol Also yes the spring has partly to do with easy construction, but it also was meant to be able to withstand more high speed vibration over a length of years of duty than just solder alone.

@kylehandyman 29 күн бұрын

I've been waiting till the best time and enough time to watch the whole video Keep uo the good work

@Valisk Ай бұрын

I love a good machine resto project. Looking forward to more lathe stuff!

@InheritanceMachining Ай бұрын

😁 thanks!

@Yakjzak Ай бұрын

The best and wholesome way to finish this video :]

@roylucas1027 Ай бұрын

Love your videos. Incredibly entertaining and despite myself I even learn something.

@InheritanceMachining Ай бұрын

I'll count that as a win! Thanks!

@temmieisthehoi3287 Ай бұрын

So much fun getting a notification while im at my manufacturing job and knowing i can watch inheritance after work!

@anonymousaccordionist3326 Ай бұрын

Ha, I love the use of the Polly Pocket jacket to "dress" the wheel.

@crsirbs215 Ай бұрын

The fact I’ve seen every video is crazy to me. The channel has become so classy. Long live inheritance machine

@adamhotrod Ай бұрын

Great job on this. As a cylindrical grinder myself, I'd have used a flow of coolant into the bore while grinding. This creates mess galore though so I suppoe we pick our inconveniences.

@ryanwiltz5145 Ай бұрын

Your videos are great and the sound Quality is the best of any maker video I have seen. EXCEPT for that darn phone ringing!!! Keep up the great work and sound level sound!

@alexxustube Ай бұрын

Thank you for the smile on my face. I hope, your grandfather is watching you and smiling from above, too

@lw8882 26 күн бұрын

The noise from the grinder when trying it after the first spring, and then trying it a third time both made me laugh like a madman.

@rodolfocastillo8025 Ай бұрын

Nice job!!! Keep posting I had same problem with my lathes tailstock, since i dont have toolpost grinder used a Mt2 finishing reamer which gives good results, not has shinny ,but work better than before

@benriser4018 26 күн бұрын

THANK YOU UNIVERSE! It’s been bothering me since you cleaned up the rest of the grinder that you didn’t change the filter!

@wolfparty4234 Ай бұрын

I like how you ended this video, very creative, Sir💪🏼🔥🔥🔥👍🏼😎

@jacmac5058 Ай бұрын

DAYUM. Good video as always

@kbowen2251 Ай бұрын

Watching this is a great way to start the day off of work!

@zer0reaction313 Ай бұрын

It is always a good day when IM uploads. Really like to watch your videos before sleep (not because they bore me to sleep, but rather calm my mind)

@ishersingh5759 Ай бұрын

Dude that was the best ad transition i have ever seen. Love ur vids btw

@InheritanceMachining Ай бұрын

It's quite a divided approach 😂 thanks!

@jozefdoyle4621 Ай бұрын

superb ad read!!

@kgregory666 Ай бұрын

Another great video. I have been machining for 15 years professionally and 3 months ago I started CNC cylindrical grinding. Let me tell you, there is a reason they call it an art. It's been a lot of fun to learn so far and in my limited expertise, you did a great job. I look forward to your videos every Friday. Keep up the good work!

@InheritanceMachining Ай бұрын

Very cool! And thank you. The learning is the funnest part!

@scottjones8664 Ай бұрын

Great video as always. Not only do I usually learn something, but it's always entertaining!

@InheritanceMachining Ай бұрын

Thanks, Scott!

@nolansprojects2840 Ай бұрын

Bro. The build up to that ad was genius.

@InheritanceMachining Ай бұрын

I liked it, but opinions are divided 😂

@dimitar4y Ай бұрын

@@InheritanceMachining some people hate ads because they don't use adblock and they already get bombarded with 30+ ads before the video.

@wmillios Ай бұрын

My dad told me that when one headlight goes, make sure you replace both, because it wa salmost guaranteed that the second would go pretty quickly after the first, and most likely in a rainstorm or snowstorm. For that reason, I would have replaced both springs on the grinder… I love your channel!

@klulnes Ай бұрын

as always-nice video. thanks

@johnwiley8417 Ай бұрын

13:55 Holy cow! What's this? A KZfaqr with an appropriately sized soldering iron? I'm very impressed!

@mfox2011 18 күн бұрын

Project idea: custom guards for some of your tools. You mention having guards for those belts in another video. How about something that also prevents an external grinding wheel from exploding into your face? You've got a unique challenge to keep things camera friendly, too. I'm curious what you'd come up with

@grumpygreg7505 Ай бұрын

HA !! That ending was super. I didn't even realize I was approaching the end of the vid. Then bam! A good LOL. Thanks.

@TheOfficialArgo Ай бұрын

Mike has good taste in optics!

@kudosjeg Ай бұрын

As always, I love learning from the master! Dayum!

@tik-tokar Ай бұрын

The motor runs on white smoke)) There is not enough white smoke, fill the motor with white smoke and everything will be fine)) Thanks for the interesting videos!

@giovannicintolo89 Ай бұрын

You are quickly exceeding the skill level of many life long machinists. Bravo, beautiful work as always

@Hyo9000 29 күн бұрын

Huh. After visualizing the conic section… you’re right, the trajectory of the indicator tip is hyperbolic in shape

@drachenklaue07 Ай бұрын

Have fun on the date

@altf4cerrarventana Ай бұрын

just the side project of repairing that motor could´ve been an entire video on its own that I would love to watch

@RobertBrown-lf8yq Ай бұрын

Nice ‘Exit stage left’ there mate 🤣🤣 Looking forward to the next instalment . Regards Robert

@majorrsoul2466 Ай бұрын

HOWZ THAT !! Good catch 👍

@kentswan3230 Ай бұрын

yea team!!! 😁 Your side projects are almost as much fun as your main goal. Happy to see you've got MT's whipped.

@InheritanceMachining Ай бұрын

It's all part of the fun!

@jbrownson Ай бұрын

Great video, love your style

@swampy1584 Ай бұрын

Great video as always thanks

@MrPancake0825 Ай бұрын

Your voice reminds me of Tom Bodett. You've probably heard that a million times. I enjoy your work. You make it look simple.

@pauloalvesdesouza7911 Ай бұрын

Seriously? C'mon man! You left us hanging without knowing... Kudos to the patreon who gave you the tool. Please just don't leave us waiting on the outcome of this Morse taper conundrum. Happy Easter.