Cheap and Easy Wasteboard, Fence, and Clamps for your cnc router

Рет қаралды 26,342

4 жыл бұрын

In this tutorial, I'm going to teach you how to make a super cheap and easy wasteboard for your cnc router. Next, well install a set of scrap wood guides, and finally well go over a few methods for securing your workpiece, including 2 different tape methods, and scrap wood clamps.
Surfacing bit - amzn.to/3tG2nu1
Check out www.fullsteamdesigns.com, and be sure to visit the makers resource section to find cnc router files and other info.
/ fullsteamdesigns
/ full_steam_designs
/ fullsteamdesigns
fullsteamdesigns.com/maker-re...
If you enjoy my content and would like to show your support on a more personal level, please consider checking me out on Patreon. Thank you!

Пікірлер: 48

@northwestgaming4049 Жыл бұрын

Actually I am getting ready to run my first flag for my dad. I bought a shapeoko3 to make little signs for my fence company. My mom asked for a sign for her office door. Couldn't say no so I watched you and couple other to find a flag design to disgn it and then tile it to run on my machine. Paint is a little tacky still (kinda good cuase I am hesitant to run). Your videos have helped me alot. I run a cnc punch for a manufacturer but you have helped become comfortable with my machine so I thank you.

@amandapolynone4485 3 жыл бұрын

Thank you for this video. I was feeling overwhelmed and was going to buy everything to make the threaded wasteboard I see everywhere. This is honestly more up my alley and will work perfectly for me. Thank you for saving me the time and headache!

@ChrisPowellFSD 3 жыл бұрын

That was the first thing I did when I got mine. What a mistake that was.

@granthultman2914 4 жыл бұрын

Well done!!! Sweet dust boot! Great instructional audio and tone.

@Celtundrica00 4 жыл бұрын

You are an awesome teacher dude. Thanks for this.

@jeffcowden7079 4 жыл бұрын

Great video and thank you for the information, keep up the good work!

@kurtc9687 4 жыл бұрын

Thanks for the video. Creating a waste board is my next project.

@williamgibbs4119 4 жыл бұрын

Awesome video. Thank you for sharing this. I hope you post more how to videos on the CNC. Just purchased an XXL and eager to learn more about it. Brand new to the CNC world.

@cliff5240 4 жыл бұрын

Great video!!!Just got my machine last month so still learning

@miketrent7976 4 жыл бұрын

Very informative! Looking forward to the tramming video

@tribal283 4 жыл бұрын

Excellent video man 👌🏼

@davidbarton87 4 жыл бұрын

Looking good!!!

@brittond14 4 жыл бұрын

Good Video sir. Thank you for the instruction! Some of your techniques are quite original and all are well thought out. Cheers!

@ChrisPowellFSD 4 жыл бұрын

Thanks! I’ve tried a few different setups, and this just seems to be the one that works best with my workflow.

@rogdotcom1 3 жыл бұрын

Informative and easy to follow, great job on making this video, really appreciate it 👍

@ChrisPowellFSD 3 жыл бұрын

Thanks for watching!

@botoepfer8588 3 жыл бұрын

Great video Chris, I messed up my first waste board by surfacing myself in to a hole,, Like what you did here

@ChrisPowellFSD 3 жыл бұрын

Thanks. I’m working on another style right now for the Frankenpoko. Should have a video out about it soon.

@stephenfrisby2194 3 жыл бұрын

Just an extra step that I have found it very effective is to use diluted varnish/sealer for the base board especially as The MDF or Chip Board is very sensitive to Humidity. Honestly it makes a difference also keeps board looking nice and easy to clean. I actually use 2 pack automotive clear, seal edges first and back of the board, flip it over mount and install insert nuts ect, Do a suface cut then seal top and edges again give a light sand and one full coat of clear at 10%. All just brushed on and throw brush away after. I live in Melbourne Australia so our humidity changes a lot in a day.

@ChrisPowellFSD 3 жыл бұрын

That sounds like a good idea. I might give that a try on my next one.

@JohnColgan. 3 жыл бұрын

Great hints, thanks for sharing

@ChrisPowellFSD 3 жыл бұрын

Thanks for watching

@MalletCNCWorks 3 жыл бұрын

Nice work and information

@ChrisPowellFSD 3 жыл бұрын

Thanks!

@Todd-W 4 жыл бұрын

i hit the like and subscribe button but funny thing happened when I hit the subscribe button: A KZfaq message popped up and said "If you follow Chris Powell any closer, he will be forced to file stalking charges against you. Please refrain from hitting the subscribe button more than 27 times, otherwise you're playing with it." LOL.. always good and thorough videos Chris.

@ChrisPowellFSD 4 жыл бұрын

Someone at KZfaq must have it out for me haha.

@FormerlyKnownAsAndrew 3 жыл бұрын

Great video! Thanks. At 3:34 did you take any sort of measurement to align the wasteboard before screwing it down?

@resorter66 4 жыл бұрын

Chris great video i am ready to do a nes waste board and squaring rails. Good tip on making sure the squaring piecers ar square ti the router.. Did you just put the bit in and set a depth and start the router an jog it manually.? And that was an 1/8" bit right. Also I see that you have one of the rear dust port dust shoes I have one also and am having trouble attaching the hose to something solid on the back side to keep the hose in place. Could you share ho you hold your in place . Thanks Jeff

@ChrisPowellFSD 4 жыл бұрын

Thanks. Yea it’s an 1/8” bit. I just got it close by eye and touched off on the top of the guide. Then I just lowered it and jogged it manually. I just run it up the back and use a hose clamp to secure it to the top z axis pulley cover.

@resorter66 4 жыл бұрын

@@ChrisPowellFSD Thanks

@mikesapp755 3 жыл бұрын

Nice video. What do I need to do if I am making larger 32-33 inch projects? I am going to try your method.

@ChrisPowellFSD 3 жыл бұрын

The max travel these have is 32x32, but the wasteboard would have to overhang in the front.

@resorter66 3 жыл бұрын

I am watching this video again .Chris looks like you have a piece of mdf that has tee nuts in it that the new board you just installed over it . is the one with the tee nuts in it the original bottom for the machine or a second piece of mdf Jeff

@ChrisPowellFSD 3 жыл бұрын

That’s in the original wasteboard. I made the mistake of installing those when I first got the machine, and never used a single one.

@resorter66 3 жыл бұрын

@@ChrisPowellFSD Does the new spoil board come up to the top of the front and back rails so you can do tiling if you have a project that calls it. just wondering I make custom cabinets for a remodeler

@resorter66 3 жыл бұрын

that are longer than the cutting area on the xxl So I use the tiling tool path in VCarve Pro.

@ChrisPowellFSD 3 жыл бұрын

@@resorter66 I just put them in the machinable area so the whole surface can be surfaced. Otherwise you wouldn’t be able to tile a project.

@KYWT 3 жыл бұрын

Nice vid....hey what dust shoe is that? I've always wanted to try a back hose like that! John S from SO FB group btw.

@ChrisPowellFSD 3 жыл бұрын

Thanks John. It’s a PwnCNC

@donniehughes7054 3 жыл бұрын

Do you have a video on design for Carbide Create?

@ChrisPowellFSD 3 жыл бұрын

Tons of them. Here’s the whole play list. kzfaq.info/sun/PL6BcRGh7FY3AHUgVGnBcyhlyFWdASm1j3

@ChrisPowellFSD 3 жыл бұрын

This is a good one that covered a lot of the tools in CC. kzfaq.info/get/bejne/npyTppuY0KusiHk.html

@FloppyHatPhotos 4 жыл бұрын

Hello Why not make the waste board as big as the cutter can cut? Have a great day. Patrick

@ChrisPowellFSD 4 жыл бұрын

It’s just a little within the max size. You don’t have to come in a full inch, you just need to make sure you take the radius of the bit into consideration.

@dasfreakster 4 жыл бұрын

What is that circular saw setup you were using?

@ChrisPowellFSD 4 жыл бұрын

That’s a Wen track saw. Best $130 I’ve ever spent.

@kimberlyashcraft7841 2 жыл бұрын

I’m crying!! I can NOT get the spoilboard right. Countless failed attempts and I have no idea what I’m doing wrong. I’m so sick of rpm, ipm, Chip load, post processor, zeroing repeatedly. Seriously about to throw away this Onefinity cnc that I wanted so bad and waited forever for. I’m sure it’s not the machine, but operator error. I’ve watched ever KZfaq video and read every forum. I’ve never felt so dumb.

@ChrisPowellFSD 2 жыл бұрын

What’s going on with it? Shoot me an email or message me on Instagram and we should be able to figure it out.