How to Rebuild A Hydraulic Cylinder

Рет қаралды 27,625

2 жыл бұрын

Today Pete is showing how to rebuild a hydraulic cylinder. This cylinder is off a Kubota B21. This will work on all of all the Kubota hydraulic cylinders and most of the main tractor brands too. It is the Same as John Deere,International and New Holland.

Пікірлер: 31

@TylerTheFieldServiceTech 4 күн бұрын

Straight up, this was a fantastic video. Very easy to understand and follow with great explanations. You just need a bigger pipe wrench or a cheater pipe. Downward force on the wrench from and elevated position is a recipe for a head injury.

@jimmyhunter8706 Жыл бұрын

Excellent video! Good camera angles where I could see everything. But the main thing is just the ideal amount of conciseness!

@111alien111 9 күн бұрын

Thank you brother, much appreciated for your time. Got to do this tomorrow

@boostedcruiser04 6 ай бұрын

Not a bad idea to run a ball hone down the barrel while it’s apart. That’ll give it a nice surface for them piston and gland seals to seal against and remove any light surface imperfections that could damage the new o rings, wear rings, etc.

@boprosplumbing 10 ай бұрын

Thank you sir. Had to replace a hydraulic hose on the skid steer. Figured I ought to seal the cylinder while the reservoir was already empty lol You also have great attention to detail, noting things that are significant, great how-to guide!

@edhultgren517 7 ай бұрын

Well done sir. I think I might be able to replace the seals on my splitter after watching. Thanks

@Couch_engineer Жыл бұрын

Great video. Quick tip, buy chef gloves instead of those blue ones. They’re exceptionally strong. Better than mechanics gloves. Cheers

@markedmonds6604 Жыл бұрын

Thanks Pete! I had did cylinders before, but I wanted a refresher video and yours we're great!

@cheaphomesteading Жыл бұрын

Thanks for watching

@Greenacres1958 11 ай бұрын

Ok. We gonna try. 2 old women 63 and 65. I’ll let you know how it goes. I wish you were close! Lol homesteading. Can’t afford to hire out. Lol.

@Greenacres1958 11 ай бұрын

Thank you! I’ll check back in when we get it done. In Oklahoma. Hot right now. May not be for a few days. I’m gonna watch this a few times before we try.

@treeclimberdave 7 ай бұрын

@@Greenacres1958 how did it go?!

@spukduk5632 Ай бұрын

@@treeclimberdave they died

@ke6bnl 2 жыл бұрын

I loosen the flange nut while on the tractor.

@cheaphomesteading 2 жыл бұрын

That’s a good way to do it Especially when the flange is super tight. Thanks for watching Man

@homegrowncountryhomeplace 2 жыл бұрын

Good tutorial video Pete. Learned a lot from this video. Have a Blessed Day Friend. Justin

@cheaphomesteading 2 жыл бұрын

Thanks man. Hope you and your family have a blessed day my friend

@randyschmittou8708 Күн бұрын

Great video! Thanks for sharing. Do you use the red loctite? I'm going to rebuild the leaking cylinders on my Ford tractor. The one that's leaking is the bucket cylinder. Thanks Pete and God Bless you.

@onlypixie5929 4 ай бұрын

Excellent video. Thanks a lot for this work.

@ke6bnl 2 жыл бұрын

Good explanation, i just did my Kubota bucket cylinder was just like that. Only thing i did differant was to heat the piston seal to about 200 degrees in hyd. Oil to soften it up.