There JX lineup prior to these ones are badass! The JX500/1000’s are still maintaining there value pretty well. This one is a no brainer you can use and hold onto for years!!!

Where are the 5 and or 6 channel JDs,

I find JX amplifiers online but impossible to find JD. Are they différent ?

Damn good amp. Im using it to push 2 w0v3 15's & it sounds amazing. Amp barely gets warm during extended run times.

Yea..I just wanted to ask about the no need for line out put-convertor ? So just cut the plug off the end of a r.c.a. cable &. tap into a rear speaker wire? ( I’ve actually done this with a J X 500.1 - it worked ,but had sound quality issues) And if I don’t use a line out put convertor ....and my car a 07 Honda Civic with factory h.u.... not sure if it has a factory amp or not..but the bass on factory speakers goes down as volume goes up... so question is “where” to the signal from.....speaker wires behind factory head unit? Or at the end of the run at the rear speaker wire in the trunk? I’m a fan of JL Audio and currently have a JL 500.5 in MKZ & a JX 500.1 with 10bass wedge in my Mustang GT...and plan to add the JD 500.1 with single 12 bass wedge in Honda Civic..I have never had any problems out of any of their equipment & in my opinion it sounds fantastic for the price...Any information regarding how to eliminate need for l.o.c. would be greatly appreciated..But more than likely I will end up getting it installed & mounted by a authorized JL Audio dealer so I won’t void my warranty ...

Just replaced my JL Audio 360.2 to the Jd500/1 today. Oooooo, she slaps!!

Buenas tardes amigo, vivo en México, y megustaria si puedes desirme qué amplificador es mejo, el RD400/4 oh, el JD400/4 Lo usaria con un set jlaudio C2.. MUCHAS GRACIAS..

Hi can anyone tell me JL a4300 amp Where is the fuse located?the amplifier does not light up when plugged in, so I wanted to check if it has an internal fuse.Thank you for all the information

Jd series is going to be the beez kneez for jl audio

Hi I have purchased the JD500/1 to power a 10w3v3. I will be running it using speaker level. The issue is the output voltage from my factory speakers goes as high as 12volts at higher volumes and the JD high level input is maxed at 8v. Would this be a problem or would you recommend me getting the LOC22? Many thanks

I got the rd because I thought it was better, but I think I should've just went with this

With the new JD series I am struggling to see any differences between the JD and RD series (at least for the 500/1 mono block variants of each) other than aesthetics and an extra $100. Can you provide any input on why the RD are better from a performance standpoint or should I just save myself some money and get the JD?

Can you 1 ohm a jl audio jx 1000d/1

Hey Davis. Just bought a JD400/4 and the clipping LED never lights up. Is this ok? Even at full gain? Everything wired correctly and good sound coming out from the speakers. Just wondering if it is possible to be at full gain without clipping. Car is a Fiesta ST with Sony unamplified head unit.

Just bought a 12w7ae with the HO box for $1.2499.99 and the jd1000/1 amp for 389.99.. Cant wait untill it all gets here! My wallet is a little salty tho..

How much tho?

The jd series 400x4 channel amp does not have a clip or protect light nor has any fuses! Not a fan any more.

Man f y’all that say this amp not lout or this thing shit I had this amp and boi it preform better then most and they can take the heat man never overheats or go in protect mode and I can tell you for a fact 💯

My jd 1000 smells burnt any idea what it could be ?

That amp is garbage people don’t buy the jd amp I put one in my friends car 🚗 it has no power get the jx