What I like about this fix is Justin... he is providing a fix that probably most marine technicians would just say "let me take a look and fix it" at the rate of 1 hour of service or more! I'm sure 90%+ of the time this fix will do the trick. Great video!

This guy is awesome, didn’t think I could get my Speedo to work at my age

Thank you. Not sure why anyone would give this a thumb down. My 200HPDI intake has been clogged up for years with wax and mud. Used the 1/16 bit with vice grips yesterday. Took some time, but worked great. I knew I was good when old filthy water came out. Thanks again.

Awesome brief to the point video! I never Gave a thought as to how my speedo worked or why it quit. I followed Justin's instructions and blew out the lower Pitot tube, still didn't work. Disconnected the tube from the Speedo and that was the problem the tubing had cracked after 16 years and needed to be replaced. Replace for under 20 bucks Amazon next day!! Thanks much!!

Thanks Justin. Exactly the video and help I needed to fix the speedo on my 115 Yamaha. Cheers from Monaco, New Zealand.

What a terrific video. I remember when I choked Austin with my speedo

Thank you 🙏🏼 this was answer to my prayer. I bought a whole new multifunction gauge cause I thought that was the problem. Glad it wasn’t and I glad I did not throw the old one away cause it wasn’t the problem.

thank you, fixed my speedo following your directions.

I;m new to all of this and it had me stumped why my speedo would not work, thank you for showing a bumb one like me how to fix it...

Thank you - I followed your advice to the tee … it worked perfectly. Thank you for your video !!

Tried this, and it worked. Thank-you.

Great Video and put me in the right direction. I have one problem, i broke the 1/16 drill bit cleaning it out. got to agressive. How do i fix it so I can use the motor speedometer?

Very good video easy to follow.

Thank you!

Thank you, Justin. You save me $500

Super helpful tip!! Thank you. I hope it fixes my issue with my digital speedometer.

Fantastic and appreciated

Worked great Dude! Such an easy fix. Thanks for taking the time.

Thanks! It's my first Yammie and I couldn't find the end of the tube. Appreciate it

NOW I know what that broken tube is for. THANK YOU!

Very good.....Actually.....EXCELLENT!!!......no bs instruction. You get a like a share and a subscribe!

Watched video went outside and cleared my speedo

After doing this, is the only way to know if it’s fixed is to get it in the water?

Thank you for video

Thanks! Great instructions. Do you just pull that tube out with needlenose pliers where the air came out at the connection? It's pretty narrow there and I didn't want to break the tube.

thanks for sharing your tips mate,,good job,

Thank you very much !!!!👍

Can you do a video on how to fix rpm gauge on Yamaha outboard 115

Thx mate.

Sir, you are amazing. Thank you. I kept getting this cotton looking material out of it, and was scared to go any further.. Well, it was fully plugged up.. in fact, it was so badly plugged up, it was acting like a little old lady on a straight cheese diet. Appreciate the video!! If you're making any new videos, I'll sub. Just reply back and I'll smash that sub button..

Excellent video.

👀TK. I like the video view 😂

IT WORKED !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! THANKS !!!!!!!!!!!!!!!!!!!!!!

I have a question..... 2004 F60TLRC what is the factory setting for the pilot screw inside the carb? Thanks for the video. I hope to get my speedo working.

Thanks!

Thanks!!!! This video helped solved my issue

Can I blow air from the other side to try the blow stuff out I think there is a piece of metal stuck in mine

Appreciate it!!!

Great video thanks for making it.

Can I blow air from the other side to blow stuff out I think there is metal stuck in mine

My 2015 has a small pin in the middle of the hole ... is that normal

Is this the same procedure for ox66 models? Thanks.

how do you test a tachometer on a Yamaha 150 HP year 2000 2 cycle outboard ?

My rpm are low on my Yamaha 150 where do i start?

how about tach fix

Thanks man!

Thanks

My favorite part is when he uses the blow gun

I tried this the other day and gear oil started leaking out of the speedometer hole on the lower unit😮‍💨

Thank you

What about a cramped hose

👍👍👍👍👍

You rock

Mine has oil coming out of the hole any body no why

I had to watch this video twice, this handsome man that works so well with his hands is too distracting. Find some less attractive people for the helpful DIY.

that cost that poor soul 1000.00

This guy definitely wears tighty whities

Thank you!