You will probably never see this comment but brother, I appreciate you. You just took all my fears of tracing this electrical bug on this 2014 silverado. I am super appreciative of you to the fullest extent. You got a like and subscriber for this!!!

SIR, YOU ARE, TO ME, A GENIUS!!! My SON'S DODGE DART HAS JUST ABOUT DRIVEN ME ABSOLUTELY INSANE. FIR TWO WEEKS, I HAVE BEEN WRESTLING WITH THIS ISSUE. THANK YOU, SO MUCH FOR DOING THIS TRAINING SESSION. ICALL THE VIDEO A TRAINING SESSION, BECAUSE, IT IS SO MUCH MORE THAN A SIMPLE VIDEO. ANYONE, THAT CAN LEARN, WILL BE RICHLY INVESTED BY WATCHING YOU SESSION. THANK YOU AGAIN AND MAY GOD BLESS YOU, SIR!!!

👏👏👏👏👏 I wish my techs were that confident and knowledgeable about their equipment!

As much as I despise electrical issues in autos, just watching you go through how you found the problem , I have a bit more faith that I can do this.. Thank you for this video..

Thank you! This is probably the only video I could find that goes into so much details for electrical issues.

this sure helps make those dreaded no comm problems a bit less mysterious. thx for posting this steve.

Just found this gold mine!!! Thanks so Much!! I have a 014 denali 4x4 for a stuck in 4wd. Was testing front actuator and encoder motor and now I lost com with multiple modules. Not sure if it came in with all those faults but at least I have a path to get results. You made another sub. Thank you Sir!!! Keep these coming!!!’

This is a fantastic video. Very informative and thorough. Thank you for posting this style of content

Best video I've ever seen. I am having an issue with me 2010 silverado1500 4x4 5.3. First it just went to no crank no start. With code P1682 so I put ignition switch and tumblers in. Then went crazy with crankshaft position sensor, low circuit temp, U0100 and U0109. I just learned how to completely test my truck. I will be commenting soon to thank you again.

Awesome diagnostics, thank you so much for sharing your experience, it was watched with pleasure ❤❤❤🎉🎉🎉

Awesome video and explanation, just super informative. Thank you so much for sharing the information as well as showing the level of detail. This also helps explain lengthy labor costs related to repairs.

This is the best video I have watched in ALONG TIME! I am having this exact issue on a 2009 Silverado… thank you for your time and knowledge

I saw your video until the end, and appreciated your technical support and knowledge.

Thank you for this. I'm tackling a U0122-00 Lost Communication with Vehicle Dynamics Control Module on my 2008 Suburban. I'll try to report back with my findings.

A very nice real world diagnostic video. Thank you for sharing.

Great troubleshooting, I'm working on a 2012 Silverado 2500HD, am not a mechanic but have many years of industrial electronics experience and I have the same "Alldata"? schematics along with correct probes and test equipment. Your MOST important point is to disconnect the vehicle battery BEFORE doing anything, no one wants "Card Fryer" added to their name. Again, a well thought out and documented presentation troubleshooting wiring/components on an automotive network, GMLAN in this case but your logical approach is valid for all others...

Absolutely paid attention the whole time. Great explanation and break downs. You should be an Instructor at UTI or wyotech because you did it better than my instructors did while i was there!!

I have spent 8 months looking for this breakdown. I have O.L. across 6&14 and til now I hadn't any reference for procedure. (Felt like an idiot out just replacing parts till it works, ecm and fuel control) Many videos but few articulating so clearly Thank you, confident I can get it now. (Although it's got a mitigating factor: Federal Conservation duty equipment removal rewiring has faulty solders RJ Hart

This is one of the best and most valuable videos I've ever watched

Your awesome. Loved everything about this video. You’re an excellent instructor. Definitely a subscriber.

Excellent video! Great troubleshooting lesson!

I'm having problems with my alarm and lights this video showe me what to look to for in the wiring system to find the short or missing curcuit thank you for the education I'll be seeki9ng you out again

u helped me diag a chevy for lost communication with fpcm THANK YOU. customer will be back on the road soon

Excellent video, thank you! I am chasing an intermittent U-code problem with a 2018 Yukon. I have a much better idea of how to break this problem into pieces and isolate the network segment(s) that are the most likely based on the error code clusters I am seeing. Thanks a LOT!

I have had work done to my vehicles at this shop and they do very good work. Enjoyed this video and would love to see more of these.

Sir, this is a great on the job, no special tools, instruction. When you are a Mom and Pop service, when you are mobile service, this is the way it's done and it is very much appreciated. Now, if I could borrow a cup of flexibility for my body I would really appreciate that also.

This is an AMAZING video!! I was literally can bus illiterate before, now I have a better understanding of it thanks so much…. Liked and subscribed!!!

awesome video having communication issues on a 2011 malibu now i’m super eager to tackle it

You just got yourself a new subscriber. Outstanding !!!

excellent walk through thanks.

thanks for sharing all this. great to have a walkthrough

Definitely new subscriber this will help me a lot with my gmc sierra diesel 2017 THANKS 🙏

good stuff great work,,,

Excellent video Steve!!!

They do help with diagnosis but they also stabilize the can bus signals.

Thank you perfect video learning a lot

Great freaking job 🙌 good stuff 🤠

Great video I wish you were close to me id bring you my 2009 tahoe that is giving me a world of issues

Very informative video!

Great Video Steve, Great Work!

Very awesome video thanks so much

Would a can bus tester been able to identify the problem too?Still admire the narrowing down through circuit testing though.

awesome excellent jo job

Thanks for this video I have a u0100 ebcm code. No lights on just showing up on the system scan. Hope i can find the problem with the help of this video.

Thanks for the video.I like to know how much can we charge for the job like this.Thanks again.

Nice Job! Quick question is that why resistors are there? For Diagnoses? Have a great day!

Where can I find the wiring diagram for a 2014 Silverado so I can diagnose the same type of issue?

THANK YOU SIR !!!!!

Mine is going through the same thing got stolen when I got it back same thing ECU is not communicating with the truck.

Very good job 👏👍 sir could you make videos on chevrolet Equinox 2020 about Radiator fan please

I’m confused shouldn’t that be check plugged in . With the in and out com lines ?

Like fixing Christmas lights. The problem isn't obvious

The only thing I don’t understand sis what are the pins that he jumps and is there any resistor in the wire that he uses to bypass ? 🤔🤔🤔help me out

What were the syptoms the customer noted before bringing it in? I'm having an U0073 and P069E code popping up on my 2011 suburban.

where can i find this wiring diagram

Hello im having problems with my 2015 silverado im getting a u0073 ebcm communication fault but im getting 60 ohms at the aldl could it be the module itself is bad no abs light have replaced wheel speed sensors, but im still having the fault and poor performance

Thanks for the vid. Did you post those schematics anywhere to print out?

Where did you find the electrical schematic? Im looking for one for a 2008 gmc sierra extended cab 5.3 and am having a tough time

Did the trailer brake controller throw a code on the DIC? My 2019 HD is throwing a service trailer brake on the DIC and service engine light is on. Took it to Autozone and scanner only shows fuel pump communication loss yet engine starts fine. Not sure if this could be the same issue with mine. I changed the trailer brake controller and the module above the spare tire and still no change.

Enjoyed your video are you going to post again soon? We miss seeing them!

2017suburban rabbits chewed some wires my mechanic fixed it then a couple of days later lives on dash on but no crank no start is now at dealer and am told ECM is bad $2900 does that sound right?

Great video on the testing/troubleshooting. I have a bad connection at PCM/ECM itself. Where can I get a wire diagram so I know what pins I am testing? (2017 Traverse) Are most cars like this with the resistor paths or is this specific to Chevy? Thank you for sharing your knowledge!

Electrical Work, Every Mechanic's Nightmare... I'm NOW SURE that Automotive Engineers Hate Us..

Shouldnt you check the ebcm powers & grounds before condemning it?

What was the outcome on the Chevrolet Equinox oil consumption video you did? I’m trying to resolve the same issue. TIA

Is it possible that the junction box acts up intermittently? I was getting about 98 ohms with it connected then when I disconnected it I’m getting about 120 ohms I’m not able to jump the wires like you did I just connected my multimeter to pin six and 14 where you would connect, your scan tool

excellent

Where are these kind of mechanics in my area??

Where can I find this printout of the wiring diagram? Same vehicle just diesel.

Hello. I have a problem with a can bus. No u codes. I can communicate with all the modules but i can't get live data. As soon as I try read the live data on any module, the scanner takes me out and display a message of no communication. I have literally done everything. I don't really know what else I can do to diagnose the can bus system.

Good afternoon Steve I was going to ask you I have a problem with my 2005 GMC Sierra 2500hd having code u1096 no communication with cluster I’m lost I check the cluster replace batteries clean ground on batteries and remove after market components. Do u have idea what it could be ?

u1041 u1026 is what I'm getting on my 04 gmc yukon and horrible fuel mileage 8mpg

Nice. Found. 😮😮😮.

BUS LIN U1501-00 ??? Check engine On , the car has no faults, but not work remote start on my Chevy Colorado 2018.

I hate those Mac lights!

Where are you located I am having code u0073 and u0077 and p0171 on my 2014 Chevrolet impala ltz 3.6L and I can’t figure it out

What if you have ol that’s means both sides are bad

Master

This for U1096.

Hello , I have a problem with my journey ? Can you please reach out to help ?

I be more than happy if you can work on my actually let me know if I can take it over to you

U1510 code anyone???

Very good diagnostics. I'am troubleshooting a 2000 c5 vette u codes 1016,u1064,& u1301 have cleared all, the u1301 & u1016 where (H) History codes & did not return,the u1064 (Loss of communication w/BCM) returns after a drive cycle. Also the U1128 (Loss of communication w/Radio returned a week late. It's been a journey but after seeing this I'am Diggin in. Best, G. E.

Hello, please can you help me because I have U and P errors for the automatic transmission, in a 2013 Malibu LT 2.5, but I can't find it, I'm attaching the errors, I would really appreciate it if you could help me. Car Scanner ELM OBD2 Version: 1.110.0/401100/GP DTC report Connection profile: Chevrolet OBD-II / EOBDDate: 20/08/2024 07:07:26 p. m. ============================ OBD-IIOBD-II DTCs: 10 ---------------------------- P0700 [0x0700] Transmission control system, MIL request - circuit malfunction Estatus: Confirmada ---------------------------- P077C [0x077C] Output speed sensor - circuit low Estatus: Confirmada ---------------------------- P07BF [0x07BF] Input shaft speed (ISS) sensor/turbine shaft speed (TSS) sensor A - circuit low Estatus: Confirmada ---------------------------- ============================ Unidad de control del motorUnidad de control del motor DTCs: 2 ---------------------------- P0700 [0x0700] Transmission control system, MIL request - circuit malfunction General Electrical Failures [0x00] Estatus: DTC supported by calibration, Current DTC, Test failed since DTC cleared, History DTC, Current DTC since power up ---------------------------- P077C [0x077C] Output speed sensor - circuit low General Electrical Failures [0x00] Estatus: GM failure record ============================ Unidad de control de la transmisión #2Unidad de control de la transmisión #2 DTCs: 2 ---------------------------- P077C [0x077C] Output speed sensor - circuit low General Electrical Failures [0x00] Estatus: DTC supported by calibration, Current DTC, Test not passed since DTC cleared, Test failed since DTC cleared, History DTC, Test not passed since current power up, Current DTC since power up, Warning Indicator Requested ---------------------------- P07BF [0x07BF] Input shaft speed (ISS) sensor/turbine shaft speed (TSS) sensor A - circuit low General Electrical Failures [0x00] Estatus: DTC supported by calibration, Current DTC, Test not passed since DTC cleared, Test failed since DTC cleared, History DTC, Test not passed since current power up, Current DTC since power up, Warning Indicator Requested ============================ BCM Los códigos de fallas no son detectados. ============================ EPS / TDM Los códigos de fallas no son detectados. ============================ ABS/EBCM/ESCABS/EBCM/ESC DTCs: 3 ---------------------------- U0422 [0xC422] Invalid data received - body control module Invalid Data Received From Body Control Module; Invalid Data Received From Body Control Module Message Counter Incorrect; Invalid Data Received From Body Control Module Bus Signal Checksum Error Bus Signal/Message Failures: invalid serial data received [0x71] Estatus: DTC supported by calibration, Current DTC, Test not passed since DTC cleared, Test failed since DTC cleared, History DTC, Test not passed since current power up, Current DTC since power up ---------------------------- U0402 [0xC402] Invalid data received - transmission control module (TCM) Invalid Data Received From Transmission Control Module Message Counter Incorrect; Invalid Data Received From Transmission Control Module Parity Error; Invalid Data Received From Transmission Control Module Bus Signal Checksum Error Bus Signal/Message Failures: invalid serial data received [0x71] Estatus: DTC supported by calibration, Current DTC, Test failed since DTC cleared, History