salaam, I've just encountered ur channel.. MashaAllah.. it's superb..! very clear, simple and easily understand tutorial.. I'm a noob to electronics.. but I always have the desire of learning it as hobby..! Great video.. I've subscribed to ur channel.. you earned it brother.. salaam

Great choice of music. Helps with focusing on the vid actually.

Bro, Ami je koto khushi hoyechi bole bujhate parbo na. Onek din dhore emon ekta tutorial khujchilam. Thanks a lot .

it's superb..! very clear, simple and easily understand

Hi and congratulations on your videos. It could help me. I have a Thes 3251 btp TV and I would like to put the main board universal because the main one breaks continuously. My LCD panel has the number v315b1-L08 rev.c2. Could you please tell me if there is a compatible universal main board? And where to buy it? Thank you so much and sorry for the trouble.

Thanks for the detailed tutorial.

You are a genius; keep up the good work.

hi! what if the LCD panel has a thin flex cable for back light power input not a single 2 pin wire?

The video will be helpful to repair the LCD LED TV.

Your very good,think i will alot of from you,i have alread subscribe!!

What if my TV56 is just switching on/off is it possible that it is damaged or the power supply? My nephew burned it by using 12v2A without noticing it is 12V41

Can a universal board will be done back to its factory setting after flashing firmware but it happened the monitor was broken so that i could re use it to another good lcd tv

Thank you so much very nice explain.

Can you make the monitor wireless ? Without the raspberry pi or any computer.. just with the screen and all the board

can I use this board to replace my dell 2709w board?

all the displays needs inverter? or only lcd without led backlight?

Hi, my display's model is LTN150XD-L02, Panel Type: a-Si TFT-LCD , LCM, Lamp Type CCFL, I don't get the voltage info and will the board you mentioned work? and what type of cable and back-light board will I attach?

A question: In a Lg lcd tv ADJ is paired with A-DIM or P-DIM

"LVDS pin 1,2,3 should give voltage set by jumper." Can this voltage be measured in multimeter before flashing the firmware?

Is it possible to control kodi with the included remote control?

Can I use this circuit for n156bge-e42 led?

I have a big Sharp Aquos lcd Display. Which Converter Should i use ?

I just bought a 8503 lcd controller board, the product readily come with free program driver board so it says no need firmware, but when I power on the screen, only white light and nothing happens, do you have any idea why? how do I check if the board really has a software installed in it?

Help me my inverter got a ccfl but my monitor has a 10 pin led wire.what should i do

Nice tutorial .. & where can I get the firmwares, Thx & Nice Pi, too

What can you do with TPDV1240??plz help!!!

Do these boards come with the firmware .bin files on CD?

Hello, I have a query, my lcd model number is N154i2-l02 according to data sheet I have to use 1ch 6bit 30pin lvds cable, can I use 2 channels 6 bit lvds cable. Also what is the specifications of power supply to be used?

hola muy buen tutorial.tengo una placa tv 56031 y necesito hacerla funcionar con un panel t200w02 de 21 pulgadas y 6 lamparas.las lamparas encienden pero no se muestra imagen.de donde puedo sacar firmwares para probar?gracias

ass,sy punya lcd laptop merk ACER gmn cara bisa di pergunakan sebgai tv ..pertanyyan say mesin yang cocok untuk lcd itu apa ya ? tolong di bantu ya .terima kasih

Do you have Z. VST. V56RJB firmware? I didn't find the firmware

the best tutorial, thanks

how can I get software for vst59s.p89?

well explained video sir 👍 i have display model - N156BGE-EA2 should i use ccfl inverter or not ??

I have board. I wanna install the firmware. I did it exactly the way you did but nothing happen. And there was no blinking? Can you please help me?

Hello I got B141EW04 V3 is this LCD is suitable for this controller board????

Hi, could you help me? I have T.SK106A.03 and 1280x800 15.6 inch LTN154X3-L06. I cant find right firmware, on bangood or anywheare else, the only one i managed to find is for some suspicious 14.1 inch dispay, please help I really would like it to work and I dont want to lose this board by flashing wrong firmware

Mr. Please Help me, how to download the firmware software. the link you gave to video, it can't be downloaded again

Neatly explained. Very helpful for learners.nag.

im sorry, what if my display is LVDS (2 ch, 6-bit) , 30 pins Connector? will any board work?

Great tutorial, thank you! How did you modificate the speaker cable? In my case I have a 8 pin set of 4 speakers and as yours the speaker port of the control board only has 4 pins and I don't know if I can do any modification and use this set of speakers in my project

Very much impressed.TKQ VM

How to enable HDMI-CEC feature in combo motherboards (ru 10.c816a)?

Hi Mr.Rajib, is USB for connection as USB monitor or only USB Media player/viewer ? Thank you in advance. Nice video.

hello friend, very nice video, but I have a question, I have the same LCD board just like the thin board, I try to program it but it doesn't work, you can tell exactly how to download the order of the program , my screen is 15.6 thank you

Where can i find this lcd board's with cables in Bangladesh? for my old laptop screen?

do you use the inverters from the laptop

what the IC (smd 8 position U1) dc-dc step down is at the power input 12v at slot 12v input from adapter (220v-12v)?what the his number-type& (thanks m-r)

If i followed the tutorial but my lcd panel is showing a white screen? What am i doing wrong?

I have laptop display of 40 pins and bought today universal controller board which is having 30 pins shouls i return it or it will work ? I am searching for LVDS connector but cannot find it

Sir in my monitor power supply have no adj it have only b-low,5v gnd ,switch but usme adj nai hai board me yahi 2pin lagni hai blow and adj please help me

Is it compulsory to do all the connections before flashing the firmware or I could flash firmware at any time by just connecting the pen drive and power?

Finally...you are awesome....thanks

very god. After I install one I'll just need to run the power supply to batteries and should be fully portable.

hello nice video but I have a question ...can this work without the backlight ?if it can then does it need any arrangements?or the graphic on lcd panel will be displayed even without backlight with no issues?

What is that vertical line at the center of screen

Can I connect that board to my old laptop screen to use it as secondary monitor for my new laptop.

good morning I have a tv56 card. how can I watch digital channels on it? Iam from México

Thanks this is a very helpful video. Does this Universal Motherboard connect into the TCON board on a Sony Bravia KD55X8005C? The TCON Board connects to two boards on the LCD screen so the universal motherboard can not connect directly to the LCD screen.

Can that be use in a 7 inch 26 pin screen?

can you help in finding firmware for T.VST59.031 to useon M240HW01 V0 lcd panel resolution is 1920x1080. all i get when i hook it up is the orange light and thats it will not do anything. help...

Sir can i use this on my compaq laptop lcd and also tell me where can i buy this product and what is the price

Sir in my LCD panel have RX0- RX0+ ,RX1- RX1+, RX2- RX2+, RXCLK- RXCLK+, RX3- RX3+ so sir where I connect in v56 LVDS pin odd and even I m confused in even and odd. Please help me about this. And sir universal board have clock in even pin no. 15,16 and 27,28 there is no odd clock pin please correct me if I am wrong.

Hi, I have this type of TV, when i turn it on, it shows blue screen for couple of seconds and disappears. audio works but screen black out. after many tries, if it starts to work, then there is no issue. do u have an idea for that, thanks.

does this work with plasma t.v's

Vro amar akta (Samsung S19F350HNW 18.5 Inch LED Monitor)Monitor ase ar jonno kun China universal lcd/led tv board nibo ?

TECHNOLOGY IS GROWING FASTER

I opened 4 monitor, the first 3 was not even compatible by LVDS cable, now I have a monitor which is compatible, but it has 4x 2pin CCFL, so 4 Lamp, but I have a 1 lamp inventer only, how to solve that? can I connect multiple lamps to one CCFL driver?

apakah lcd tablet bisa buat tv/monitor

NIce tutorial , can i message you i need some help to connect lvds cable , theres something ddc power, ddc clock and ddc data , where should i connect this on T.V56.03 ?

very usefull sir

Mera ek screen hai HT140wxb-601.. laptop on karne se backlight nahi aata h.. par picture ATA h. Should I proceed to make a TV with this screen??

mine have different manual for the screen adjustment is working well but the picture is upsidedown so I need the factory setting code please can u help me

hello, do you have the link for firmware? thanks

Hi. in the video you say that you will make a video on how to find the LVDS cable correctly. do you have a good link?

Thank you sir.

where can I find bin file v59 for lcd monitor LTM220M1-L01, please?

Thank u for your video 😊😊😊

hey know of any other projects within the spheres of assemblies that I can run with to make good margins as well as a bridge into parts/products manufacturing (looking for exposure; Iron sharpens Iron)?

good job and thanks.

Sir MAR HD.85.031B a panel nahe marsha up bata sakti us ka price?

How can we know some what more from some chinese panels? Lots of them are simply so short as nothing on what informations concerns.

is this the same procedure on L.A.MV56U.A lcd controller board?

My lcd has 3.3v input,what to do,do i have to use a 3.3v adapter for v56 panel?

apakah bisa untuk lcd tablet 7 inch

Hello Sir! Please help me in a problem that i have encountered. I bought a v29 board on ebay for 10$. I found a bin file for my resolution online and put it on a usb stick. After i inserted the stick the led started to flash and it kept flashing. After 5 or 6 minutes i unplugged the power supply and now nothing works. I cannot reflash it with other bin file. I tried another bin file and the led does not flash. It doesn't want to reprogram. Please help me with my problem. Thank you!

Y en donde se puede compar

Salam bhai 40 pin lvds cable laptop led screen ki universal board kah liye kahan say miljaygi

tv de lcd 32 aoc qual placa se usa e o chicote?

i have an universal lcd/led tv board v 53.03 and screen of 19" resolution 1366*768 can you send me a link where i can download the required firmware

Rajib ji i had hp pro 4410s screen ca i make tb of it

nice one ....send me it via pdf formatt for an ease in learning

Very useful thanks ser

Sir i need software of HDV56U-AS V2.1 I have searched on the internet but can't find it. Please help as soon as possible

is there any version of this support dvb-t module?

una consulta, en el datasheet de la controladora V56 veo que dice Single/dual LVDS. Pero he visto una controladora LCD mas reciente el modelo mnt68676.2a donde tambien dice que es single/dual LVDS pero este agrega un dato extra que dice (8Bits). Mi consulta es: es lo mismo ? pues en la controladora V56 no menciona ese detalle.

Mere pass ltm200kt03 LCD hay kya ye usko support karega kyonki uska firmware nahi mil raha

Can you use monitor lcd? not laptop monitor?

pls give the link wher ei purchase

How can I set the controller board to 5v