Choosing Chainsaws! // 500i, 661, 881 // Chainsaw Milling// Alaskan Mill
Рет қаралды 15,772
Жыл бұрынThere was a comment a while back about what saws i run, hopefully this scratches the itch for you!
I can go further into it, types of chain, Sprockets, set ups ect if its of intrest
Drop bellow what you want to see more of!
Ive nothing to do with Stihl fyi.
Find Me On Instagram: / the_peoples_tool
www.thepeoplestoolco.com.au
Email: Jack@thepeoplestoolco.com.au
Disclaimer:
These videos are intended to provide information and entertainment only. If you choose to imitate, duplicate or copy anything you may have observed in these videos, you do so at your own risk. The Peoples Tool Co Pty Ltd Or Jack Martin does not take any responsibility for your actions taken as a result of the information or advice on this KZfaq channel and shall not have any liability in respect of any injury or damage that may result in any form.
@brendanhose1065 5 ай бұрын
great vid thanks. good to see you get the safety squints up. always good to see people operating these big saws safe lol
@user-ex7lq1tp1s 5 ай бұрын
I’m loving the honesty of “when your 881 is broken your f&&ked” 😂 great comparison!!
@em4703 Жыл бұрын
For milling, 880/881 by far, even if you're cutting only thing 25-30" across. You don't get just substantially more longevity out of the tool, but also faster cutting speed than 100cc or smaller saws. The most important thing is tuning the carb for milling, I had to put my 881 H jet 1/2 turn out from the stock maximum richness to make the mixture rich enough for milling and to keep the temps down. I also use 33-25:1 mix ratio with synthetic oil, that also makes a big difference in milling longevity. Probably the biggest impact by far.
@ronkuzyk3836 Жыл бұрын
I can tell by your comment that you have never milled anything.
@Stump51 Жыл бұрын
What octane fuel are you using.89?..
@Mark-uh4zd 8 ай бұрын
The 881 makes sense, a whole 30 more cc’s over a 661
@soil-aint-dirt4903 Жыл бұрын
Excellent approach on where/when to use these saws. Thank you.
@babbuzzifirewood 7 ай бұрын
Nice review! I just bought a 661 for firewood/milling so I guess we have the same opinion about it. I had chance to see the 500i and try it and have to say it's really light compared to its power. Anyway I like the 661 very much.
@alexanderdaughtry4491 7 ай бұрын
Sounds like the 661 would be best for me. Lots of fire wood and i plan on building my own cabin plus i mess around with carpentry work more times than not. Ive got some old saws that need a full update so that can be used for cross cutting and fire wood if i have the 661 hooked up to the mill constantly
@MrDeano-eu9rg Жыл бұрын
Whered u get that milling attachment mate?
@archienelson9129 Жыл бұрын
would be cool to get a vid on rear handle saws vs top handle
@cbtmed1 3 ай бұрын
How do you sharpen your chains?
@nickcollins4268 5 ай бұрын
You'll feel it in your gut😅
@rrssmooth6643 Жыл бұрын
Some protective gear would be nice, can not take it back ( the moment) once it has happened. Like your review still the same.
@xxxchurch100 6 ай бұрын
No safety gear … no cred.
Surviving Ringworm
Рет қаралды 96 М.