Chris, lots of good information to explain the process and get started. Hopefully you will expand on this. I have worked on getting a good M600 replacement in Klipper and have been using the one in RATOS since the last version upgrade. It is very simple as all of the work is done in a macro M600 Here is the printer.cfg entry [filament_switch_sensor runout_sensor] pause_on_runout: False switch_pin: PG15 # also known as e4stop / e4det runout_gcode: M600 # The M600 code does all of the movement of the carriage and retraction of the filament, It also makes sure that the bed stays on. This use of the M600 enables it to be called from gcode for filament changes during printing.
@ChrisRiley10 ай бұрын
Great Dave, thanks for the info!
@chrislmink7 ай бұрын
Chris thank you so much for this video. I have been racking my brain trying to figure out why it would never pause when the sensor was triggerard and after watching your video I figured it out. Thanks again for ALL your great videos I really do learn a lot from them
@ChrisRiley7 ай бұрын
Happy to help! Thanks for watching
@tonykyle265510 ай бұрын
Thank you for this video. It allowed me to get my Ender 5 Pro EZOUT working. I had identified the pin but did not (yet) research the rest. It worked without issue all thanks to you and this video.
@ChrisRiley10 ай бұрын
Glad it helped!
@charlescarey587410 ай бұрын
Another great video Chris! I'm setting up Klipper on the Artist-D Pro and your video made the code for the filament runout sensors very easy. Thanks!
@ChrisRiley10 ай бұрын
That's great, thanks for watching!
@nobblynoel10 ай бұрын
Thanks as always Chris. I like a deep dive.. ❤
@ChrisRiley10 ай бұрын
Thank you!
@JayDmx10 ай бұрын
Hi Chris, greetings from France, you helped me a lot understanding Marlin and now putting Klipper on my Enders. Would you make a video about configuring the speeds and accelerations into slicers please? I'm a bit lost doing trial and error, even after changing some values, my print time is not so shorter, maybe I'm missing some points. Keep it up and thank you for the great videos!
@ChrisRiley10 ай бұрын
Thank you! Yes, these can be very hard to understand on how to actually make things faster. I will see what I can do to put all this in a video. Thank you for watching!
@Abyssaal110 ай бұрын
Cool video!
@ChrisRiley10 ай бұрын
Thank you!
@winandd864910 ай бұрын
Exellent! I'n just about to implement my btt smart filament sensor after the marlin to klipper switchover
@ChrisRiley10 ай бұрын
Cool, let us know how it goes!
@TheButchersbLock10 ай бұрын
11:22 I would love a video on going deeper into macros and all that confusion. For someone who doesn’t understand much about code it is like a whole differ language 😂. Very helpful video as always Sir 👍🇦🇺😊
@ChrisRiley10 ай бұрын
Thanks! More to come
@MarkRouleau10 ай бұрын
I would love to see more detail on preventing an issue if you accidentally press resume. Why does it even allow you to press resume if there is no filament?
@ChrisRiley10 ай бұрын
Yes, I think we would have to build in some more complicated logic in the macro to make it fact check the sensor to keep this from happening.
@enosunimАй бұрын
Yeah, that's cool. But I recommend installing filament movement sensor instead of this useless switch. Which is much more versatile and a must have in my opinion. You can make it from a bearing and an optical sensor. Plenty of models on the web.
@ChrisRileyАй бұрын
I have played around with them and done some videos, I might look into making one myself.
@peterr.47689 ай бұрын
Thanks alot for this detailed infos. Possible to get your configuration file as a reference?
@ChrisRiley9 ай бұрын
Here you go. drive.google.com/file/d/107AKfb9pdSrDl3zWpGUwOQBPdlGNTGDt/view?usp=drive_link
@jluvs2rideАй бұрын
Wonder if this can be done with an optical sensor. I have one left over from a TAP project.
@ChrisRiley29 күн бұрын
I'm sure it would work. It would be best to create a mount that uses a flag to trigger the sensor rather than the filament itself.
@Todestelzer10 ай бұрын
11:00 isn’t it -5mm not 5%? Looking forward for your next video. You did a tap install on Vorons or other printer with Klipper already?
@ChrisRiley10 ай бұрын
I THINK that would be 5% of the move, but I will confirm. I haven't done the tap install yet, but I do intended to do a video on it for the Trident.
@marlboromage6 ай бұрын
If you want to have Klipper check the runout sensor before the print starts, and cancel the print before it actually prints, try placing this code into your start_print macro just before the purge line is drawn: {% if not printer["filament_switch_sensor "].filament_detected %} RESPOND TYPE=error MSG="No filament detected, aborting print" #replace with M117 if you have klipperscreen CANCEL_PRINT {% else %} RESPOND MSG="Filament detected... continuing print" #replace with M117 if you have klipperscreen {% endif %} This code Is driven by the sensor state, and not by a trigger event. It should be included in main Klipper in my opinion.
@ChrisRiley6 ай бұрын
Awesome! Thanks
@FreeEnergyNerd10 ай бұрын
hi chris! very interesting video.. but you got me a little confused. If everything is set up correctly, and i run out of filament, the system will pause, do what ever i tell it and i hit resume once the new filament is in place and it will restart.. OK, i got that.. But if i run out a second time? it seemed to me in the video that it will not stop but continue? or did i misunderstand? Luc
@ChrisRiley10 ай бұрын
Hey, as long as you reset the switch after it runs out, it will trigger again. So filament runs out, it will pause, you load more resetting the switch, then hit resume, everything will work as it should. Next time it runs out, it will do the same thing. The only time you run into an issue is if you hit resume with out resetting the filament switch.
@Andre_M_3D10 ай бұрын
I have filament runout set on my sv06 plus. It is running on a pad 7 with klipper and we'll I have to say it is not reliable. It seems to work when it wants to. I noticed that it will work sometimes and keep bed warm and other times it will not keep bed warm and then require a home before you can resume. And guess what. If you hit home it will crash into the print. Lol. So my trust in the option is not so good. I had no issues with it on marlin.
@ChrisRiley10 ай бұрын
I'm a big fan of Marlin, thanks for watching!
@MrPatron10 ай бұрын
Chris. What if u have a ptfe tube all the way from the hotend to the sensor? And the sensor is a regular endstop switch with a lever? Won`t the filament collide with the lever when u retract that much?
@ChrisRiley10 ай бұрын
Yes, it can, I have run into that before. I have seen printer where they leave the PTFE loose on the extruder side so when it backs out, it will push the tube out of the way.
@RinksRides10 ай бұрын
I just bought two of the BTT sensor v2 for a tronxy x5sa and an Octopus Pro board, cant use it though, the TMC 2209's refuse to work without throwing errors and disabling themselves.
@ChrisRiley10 ай бұрын
Strange, what type of errors are you getting?
@SpectraV3i10 ай бұрын
I am trying to get klipper to work for the 12 time. Installing on a Dell Wyse 3040 Thin Client with Debian 12. 1st issue is no wifi, and during setup of configuration, wifi is seen and i add my PW to log in and click continue but it takes me back to choosing my ssid, which i choose and go through it all again
@ChrisRiley10 ай бұрын
Hey George, my guess is Network Manager isn't starting, not sure if this would be helpful. kzfaq.info/get/bejne/q9JymLFq1ay2dWg.html
@SpectraV3i10 ай бұрын
@@ChrisRiley Thank You
@kapunchino814710 ай бұрын
TFT E3 V3 FIRMWARE UPDATE, please.l can't fix my printer, and I think that is the problem