I've watched a lot of long eq videos for orchestral mockups. This is by far the most clear and concise one. Keep this type of tutorial format. Great job!

Thank You! 🙏🤍🙂

I'm writing an orchestral track for my friend's birthday. I found your video just in time! Thanks! :3

Best tip was using eq on each track of the template instead of group track. A major difference. Thank you.

Thank you sooo much for showing this! Your channel is really informative and to the point, more than any channel that I have seen. A big thank you!!!

Very helpful

Excellent Mark! Thank you so much.

Thank you Marc for sharing! A lot of hard work went into this and I greatly appreciate as do many others I'm sure.

Super helpful, Marc! Thank you for sharing these great tips!

Thank you so much for this! Really helped me approach mixing in a more efficient way

Thanks Marc!! Always so interresting!

You have a great way of explaining things! You helped a lightbulb go on for me lol! Thank you

Nice one, Marc.

Fantastic tutorial! Very helpful

Apart from Dennis Sands full mixing course (worth every penny 😊) this is best video covering the subject of muddiness on YT. Down to the point. No BS... And yes, FabFilter is a must !

It's precious tips... I'll use in my mixings... Thanks 👏👏👏🎵🎶

Many thanks Marc this was so helpful. 10/10 *****

Thanks; very instructive!

Holy sh*t. This is so well explained and demonstrated. You are a legend.

I'm really late discovering this, but just a quick note to say "thank you, Marc" - what a generous and well explained presentation. I learned a lot, and I've been doing it a while! 🙏🏼

Thank you so much. I learned in a few minutes what I’ve been trying to figure out for a couple of years now. Specifically about the software instrument stacking the room noise. Now I can focus on learning EQ instead of cutting instruments. May I apply to be your student?

This was very useful. Thx for the video.

Yes, but how we can unsterstand what kind of equalization every instrument needs?? Is there a chart for every single instrument ?

Oh wow thank you very much for this lesson really helpful 😊

Incredible work! Your content is really helpful.

wow, that is a great video, thx! can you name the sample-libraries that you use in this video? is there a list? thx again!

Super helpful, thank you!!

Thank you!

Amazing video!. Now I need a video on Compression For Orchestral Mockups 😀

man i love you

Thank you!

Marc!! cuando haras clases en español??? Eres increible, veo todos tus videos

Great video! I’m curious… Why did you EQ the horns in order to hear the cellos and not the other way round?

Hmmm you said that you preserve all low freq for the double bass but in your separate double bass video, you use high pass, since the most important for DBass is around 100hz?

Hi Marc! Do you ever use mid-side eq to center the low frequencies? What's your opinion on that? Thanks!

outside of voice recording where closed headphones are needed, do you recommend open headphones for sound monitoring only?

Excellent

Hey Marc, you havent mentioned the drums, if you do very low high pass on dbass, where do you low cut the drums pls? If you leave it as it is with dbass, shouldnt they fight for the space a lot? When i am writting i always have problem deciding what should be more in the sub, bass or drums…

Hi Marc, I have different sample libraries. Some have their dynamics to "Symphonic" sound, in which they can do mezzo-piano, pianissimo while others like Albion One, East West Hollywood or Metropolis ARK 1 that can do higher dynamic range up to forte-fortissimo. My question is how (because sections were recorded separately) to set each individual section to match other sections instruments in a specific dynamic range so they can all have equal volume in each section and not go above others. Usually the default settings have the Violins section sounding way too loud. Thanks

Wow!!!!

Why this string sound so "Hiss" in high end??

No matter how much I try to equalize the horns they still put pressure on the ears, unless, of course they cut out the entire middle! And if you also write a part of short violas under them, it gets even worse_)

These videos are wonderful and remind me of why I hire an expert to do this. I really cannot hear the things you hear!

How to use articulations?

Hi marc, what strings r u using?

This gentleman seems as though he is very knowledgeable and an expert in what he does. I have heard that he has courses that can be purchased. Has anyone on this post purchased a course from him and, if so, what is your opinion?

Wow! From the Clarity of speech, the very condensed and well presented knowledge to the the whole production quality with the lighting, color grading, sound quality and the little tension music in the background. Literally EVERYTHING in this video is just outstanding. Bravo! 👏

what string library is that?

Sorry but a lot of this advice is misguided. You don't need to highpass everything, the phasing you create far outweighs the inaudible amount of room tone you'll remove. If you can't hear any issues in the lows of your mix you shouldn't be reaching for those highpasses. You should also cut/boost as much as a sound needs and not stop arbitrarily at 3db. If you move a microphone around a room you will get drastic changes in the spectrum far exceeding 3db, why would EQing be any different? Some rooms have large resonances that need cutting, some libraries have notes that are improperly balanced, you should cut and boost according to ear always whether you're going for a natural sound or not.