I created this video with the KZfaq Slideshow Creator ( / upload )
Пікірлер: 41
@ScouTendo9 жыл бұрын
I drove for like 1 year and few months without servo and it was a pain in the ass... After ordering the new relays for 13€ and doing everything you showed right here, it is working again and I can get another 2 year TÜV license! Thanks a lot!
@LiorBD677 жыл бұрын
Thank!! Great Video. Worked fine on my Punto 2001. It is not very easy to un solder the wires (a third hand may help), but saved me a lot of $$$. Thanks again
@adelinobarbosa2056 Жыл бұрын
Thanks a lot for ur video.
@fiatpuntocityservo698510 жыл бұрын
This is manual how to repair City servo by yourself. Any additional questions or if is not clear with anything please left comment. Thank you.
@chandreshwarnaik24492 жыл бұрын
Why wiper controller relay goes off often
@zulu83735 жыл бұрын
Hello first thank you for sharing knowledge and the good welling. Second, Maybe it's stupid question. In my fiat punto 2 2001 model with same hard steering problem (I bought it like that old owner mentioned the issue). In my car I don't have city servo button. Is that signify that my car doesn't have the power steering motor at all or is it the same as your case but without city servo ? Thank you in advance
@robinschneider243510 жыл бұрын
heel goede video , thanks
@lamarjohnson91457 жыл бұрын
Hi, my power steering works fine but only the city servo button light is on. Turning the key (system test) does make the city servo red light in dash light up. But other than that, no respone by pressing the city servo button. Not when standing still nor when driving at whatever speed. Could this be related to the relay? Thanks for the video :)
@fiatpuntocityservo698510 жыл бұрын
Hello mustafa, yes, wires must be connect back. Everything what you unconnected to take old relays off, must be connected back with a new relays.
@PeterFreitag6 жыл бұрын
Thank you
@jasonfree83376 жыл бұрын
Do it need re-calibrating ??
@pablomateu7 жыл бұрын
Hello, first of all thank you for sharing your solution for this problem. I am having the same issue in my Fiat Punto (year 2004). In my case, some times blocks and some times not, but last days is getting blocked more and more often. My doubt is if the solution that you explain in your videos works for my Punto version or not. I have readed in some forum comments that some versions of Punto have different servos... I didn't tried anything yet because I would like to be sure before. Thank you very much.
@fiatpuntocityservo69857 жыл бұрын
Hi, thank you for you comment. I think yes, wil be working on your car as well, but I think you have to buy a new different relay. First take servo off and check the number of relay. Buy on ebay a new one´s. remember, Always change both of them.
@jijidinpipera4 жыл бұрын
Are you talking about the city-mode from Fiat? If yes, can you please explain a little how it actually works ? Technical speaking. Thanks
@Emperion30007 жыл бұрын
Great video! Thanks. Do you think these relays will work for a Panda 1.2 (year 2005) or will I need different ones?
@abuhasan24132 жыл бұрын
I got the same problem with fiat panda 1.2 (year 2005). Did that got fixed?
@zancho1136 жыл бұрын
I have fiat punto 2001 and my relay is tyco v23072 c1061 x127 and not tyco v23072 c1061 a308. Somewhere i saw that those two should be compatible. I would like to know if 4117 is okay to use
@fiatpuntocityservo69856 жыл бұрын
Žan . basically principle of relays is the same. I think you can use 4117 as me.
@zancho1136 жыл бұрын
Thank you :)
@bangalula9 жыл бұрын
Hi, i have build electric car from fiat grande punto. I have a weird problem with servo. When everything is hook up on board computer my servo does not work, and all other things are working. But if i unplug cable from computer my servo is working fine but then my abs and some other things does not work.i have try to remove one by one wire from computer but eventhough if only one wire is connected servo is not working. Is there a way how to fix it? To start servo manually to be active? Weird situation when u give contact with key servo doesn't work but if all the wires are removed from board computer and u give contact servo is working fine :(
@fiatpuntocityservo69858 жыл бұрын
+bangalula have you correct rotor for this car?
@giamar86376 жыл бұрын
Hi,could you tell me which ones are the positive and negative cables?? I think in total are 9 cables,I would like to connect the motor direct to a car battery. Thank you very much
@mira57516 жыл бұрын
You cannot do it. It is a stepper motor and switched by electronic means
@karinchen18 жыл бұрын
Her er reperations anvisningen på din servostyring, jeg har bestilt to relæer, du skiller bare motoren ad so kommer jeg.
@furkandemirci90866 жыл бұрын
Will this work on fiat punto 2003 model and if so do you need different relays or the same you used in the video?
@bjornbach16914 жыл бұрын
Mine is differend 2003, 188b. No relays on top. Servo with Service part 26103598 Displays REV 03A
@daviddr9510 жыл бұрын
Hi, Thanks for the video. Can I desolder the tin with normal welder?
@fiatpuntocityservo698510 жыл бұрын
Yes, I did it with normal welder.
@dravenbryson60532 жыл бұрын
you probably dont care at all but does anybody know of a trick to get back into an instagram account?? I was stupid lost my account password. I love any help you can offer me
@harveyjacoby47252 жыл бұрын
@Draven Bryson Instablaster :)
@dravenbryson60532 жыл бұрын
@Harvey Jacoby i really appreciate your reply. I got to the site on google and im in the hacking process now. I see it takes quite some time so I will reply here later when my account password hopefully is recovered.
@dravenbryson60532 жыл бұрын
@Harvey Jacoby It worked and I finally got access to my account again. I'm so happy:D Thanks so much you saved my account!
@mustafaal-jaibaji268010 жыл бұрын
Hello Thank you for the video, i have the same problem, and will give your video a shot. However, you lost me when installing the new relay, I must connect the wires again, eh ??
@giuseppedardano63986 жыл бұрын
No of course you don't have to reconnect the wires..
@mr-k20248 жыл бұрын
Hi, My city servo works some times in a week, what could me possible reason to this ? do i need changing the RELAYS ?? or some other problem ? thanks
@fiatpuntocityservo69858 жыл бұрын
Dear +rohankebria = this is typicall issue of relays but can by issue also with connection between relays and PCB-board, Let´s say "cold" contact as picture in video 2:00 - 2.03 or One of the relay are not working properly. Typical relays issue - some times working and some times not ( they are sticket on the relay and shocks or different temperature in the night/ day can help to unstick). You need to change relay. Both of them for sure. They are not expensive. 1. Try to reconnect with iron soldering the conections of relays marked in video 2 min. If doesn ´t help you need use step 2. 2. Change relays.
@mr-k20248 жыл бұрын
+Fiat Punto City servo Thanks for your response. What do you mean by COLD JUNCTION ? regards.
@johntennant4596 жыл бұрын
Where can I buy relays for my fiat pinto
@panpan62625 жыл бұрын
I changed my relay both but when you turn left stop working... Only left...
@giovannibergoglio5463 Жыл бұрын
il servosterzo in dotazione sulle vetture FIAT e FORD è di pessima qualità molto pericoloso perché tende a bloccarsi improvvisamente