Sir, is it possible you make a chart or a table for all the requirements for beams and columns, their size, spacing, steel dia, number of steel bars, size of footing, type of footing, depth of footing, sbc, conc grade etc.. for domestic and commercial buildings from G+1 up to G+10? It will be very helpful and we will appreciate.

*That formula is applicable if the column has a pin support and no moment at base other wise you need to include the moment which the porduced by lateral loads such as earthquake and wind.*

Nicely explained The question arises whether the 0.00 level of the building is raised in relation to the ground, e.g. 0.5 m up. How to read the foundation level according to the formula (whether in relation to the construction embankment or in the native soil) E.G. calculated foot depth 1.5m. , whether to count relative to the native soil or relative to the 0.00 level?

Very precise and the simplest way of explanation.Thanks a lot brother.

The assesment of an effective depth of foundation is usually one of judgement or design office procedure but a ratio of width of base to overall thickness of 5 is fairly a good starting point. In rectangular section the width is taken as the shorter side.

First of all I would like to express my appreciation for your support. We are in a proses of building G5. However we are making a mistake when we aligned the foundation column from 5 to 10 cm. The pad is poured with concrete but the columns are not poured yet. Q.1- is it ok to bend the rebar to fix the alignment? If so what is the recommended or the min and the maximum limit to bend the rebar Q-2 how deep we have to chisel the foundation pad to bend the rebars and is additional support required ? Thank you ! I would look forward to get the information

How to calculate the total load(L.L+D.L) for a residential building?

Sir, in practice or at a particular site how to know the value for angle of Repose.

Excellent .. plz can we consedration this formula for thickness of footing or raft foundation in same time ? ..Thx

Great video plss keep it up

Can't get enough of that 'DEPT..thh of foundation'

Excellent. Shukran

Thanks for sharing the video. Please advise us Depth of Foundation and Depth of Footing - what is the difference?

What about stepped footings depth same as rectangle or any other method plzz replyy iam waiting sir...🙂

Whats the depth of foundation should be for a house of modern bricks with 3 bedroom, 1 bath, living, dining and kitchen. Allowance should be considered for putting a second floor in the future with the same amount of unit and considering walls to be the standard height of 9 ft?

Can you please explain if the building having basement...this will apply or any other calculation to be added into it... please clear my doubts

EXCELLENT BRATHER..... GOD BLESS YOU IMMENSELY

how many bags of cement for 1.5 x 1 meters depth footing or how thick should be concrete cement for this footing

Sir the unit of load p should be in Newton and not in kg / m2 because then it's pressure

Very well explained, thank you!

Great job ! Sir

Dear sir, Kindly note.. IS means not Indian standard..SI means International standard.

This vedio is very good for our knowledge. So please do next vedio about desing of slab and beams for building. Thank you so much sir.

That's a very finding solution to know the depth of foundation is clear.base on the sapmle formula to build that.

Thanks a lot

what will be the depth of footing pad for 3-6 storey residential building la?

Excellent my brother .. we hope to make video about dimension of column for 1-8 story .. thx alot

Sir thanks very much for your help. 🙏👍🕋🕋🕋🕋🕋🕋🕋🕋🕋. GOd bless you. INSHA ALLAA YOU WILL BE IN JANNA FARDAWSA .

thanks you so much sir. for your valuable informations

I have learned somewhere that its soil bearing capacity upon density of soil

Sir beam main hum nay L/16 raka hain L is length hain ye 16 kia hain plz explain ?

Watching from Kenya, loving it.

So useful information sir

Is it for each footing of the foundation or that with the most structural load?

very helpful. thanks

Thanks For Teaching Sir

Good n clear teaching

Great schooling thanks!!!

I enjoy your lectures

Mr White Board is invisible????? But u r Formula is Great 👍👌 Use best video camera 🎥 sharp Pictures 📷

Great explanation. 👍

Thank you, very good explained.

You did not mention if there is filling at foundation site

Sir, what is the angle of friction unit ,can you explain plz....

GOOD, TEACHING ON CIVIL ENGINEER IDEA.

Thank you Sir, very Nice lecture

Aselamualykum werahmetullahy my brother,how can determine the depth of foundation for masjid minara?

I understad clearly bro. Thank u

Thank you teacher. Is it possible to receive a certificate

Thank you!!

How do we find the structure load on foundation

Is code to hme v pata hai j batao konsa is code hai

How to calculate structural load ?

Super video

Aijaz sab

hello sir, can I know is this formula applicable for both deep and shallow foundation?

Thank you Sir

How can we determine the bearing soil to place the footing?

Explained nicely but these values ​​from the example of 1500kg / 1m2 are probably a wooden hut with a reed roof :-) Greetings from Poland

Sir what is the depth of foundation and length & breadth for single story house.

Thank you sir for your video

Assalamo alaykom Sir. I'm thankful for your lecture on depth of foundation. My clarification is, would I use the actual information from the fresh soil sample extracted right from the site?...meaning the angle of repose of the soil it actually creates, and the density without removing the moisture content of the soil sample ? Or imperative to bring the sample to a laboratory? Why I am raising this clarification is because there are construction sites the water is with in the range of the foundation depth. Shukran.

How deep should a G+12 building with 300 metre square area should be in good soil condition?

Very good advice

thank you

Building load must be in newton not in gram i think..

Bhai aap likh bada chota rahe hen mobile k through bil kul pda jaraha he font size bdahen

How to know finding a angle of repose in actual.

Well done sir❤️

Wa'aleikum Assalamu!

Bhai aap bohat chota chota likhtay hen dosra ink b light mobile fone per bilkul b pada NAHI jata plz

Thank you Sir, helps a lot.

thank you too much

& also how to find the structural load of building

You have not told any yardstick to find angle theta... How to find density of soil.... How to find structure load..

Wich type of foundation in 6 story. raft, normal, single type of footing

Sir plz solve the problem 1.8 kg / cm2 ×m3/ 1600

Sir pls upload the difference between one way and two way slab and crank bar details

HELLO SIR. CAN THE ANGLE OF REPOSE BE DETERMINED WHEN THE SOIL IS TIPPED BY A TRUCK

Yeshua HaMashiach is Adonai. Jesus is salvation. Isaiah 52:13-53:12 Blessings

how u decide angle of refose is 25....exactly how to find accurate angle of repose

Rankine Formula is not always mandatory to follow for the footing embedment depth requirement it depends on the foundation overall stiffness & arrangement to resist the vertical & lateral loads acting onto the building for the determination of P in the Rankine Equation -- it should be correctly calculated relative to each Column Applied Axial Loads otherwise - the resulted required depth of footing would be so deep & not realistic ! correct understanding & application of the Rankine Formula should be acquired !

I’m not sure - does Rankins formula give you minimum depth of foundation? It wasn’t clear in this video.

Can we use zero depth for raft foundation of a house?

Sir how will know density of different soil wait for reply

thanks alot

How is the situation in India for Muslims

how to get P value?

Thanks

Sir, How will calculate p value.

Thanks sir 🙏

What is meaning of bias

Thank you, sir!

Internal friction is very important indicator of the soil and is found on triaxial cutting samples. Soil has only two indicators cohesion and internal friction... your explanation needs improvement

Your angle of refuse explanation is not proper way. This is depend on the load of str. And this load created more presure to go to out side of fnd. That time this load make a angle and thats call angle of refuse.

👍👍

Mai I know you are using Indian standard code book then please maintain it's code book number what ever it may be

how to build a foundation in a liquefaction area.

Sir what are the types of methods to Find structure load / Building load???

سر پلیز اردو میں بتائیں