You guys should do types of mounts and muzzle devices for suppressors as a video. Would help me out a lot

Until the NFA is repealed, im just here for the sake of knowledge.

I wouldn’t worry too much about the heat/cooling rate, they are built with that in mind and will be able to handle it, tho it’s definitely also a good idea to check the owners manuals to see how much of it they are built to handle. Usually what ever that is tends to be on the conservative side similarly to how barrels that aren’t rated for +P ammunition still need to be able to handle a proof load. That being said, I would choose flow through most of the time for a semi automatic for gassing management (both of the operations system and blow back to the face) as well as because it will be better on the longevity of internal parts. Those aren’t concerns for lever or bolt action firearms and if more likely go with a more traditional baffle cannon one of those.

The comment about flow through cans not cycling subsonic ammunition was a tad misleading. Flow through suppressors do not reduce back pressure below the level of an unsuppressed rifle. If the rifle will cycle subsonic ammo without the can, it will most certainly do so with the can. I think what they mean to say is that traditional baffle stack suppressors help a rifle that isn't set up to cycle subsonics do so because they increase back pressure while flow through suppressors do not.

I dont seem to have issues with tuning. My biggest factors in choosing a can is weight, length, price and lastly noise reduction.

One point I wish had been discussed was comparing internal and external pistons (OR, piston v DI). It seems like an external piston is more suppressor-friendly, since there is (AIUI) less gas being blown back into the receiver.

I'm just beginning to look at centerfire rifle suppressors and it is overwhelming with all the options out there. Your video has been extremely helpful in answering all my questions. Thank you!

Those modular cans also allow you to dial down the diameter. The suppressor base may be able to accept a 9mm for example, but the added baffle modules can bring the exit to a .22 which greatly increases the decibel reduction of that caliber.

I have two builds planned, one an AR-15 SPR in 6mm ARC and one an AR-10 SBR in 8.6mm Blackout. When I finally get to the suppressor step, the former is getting a HUXWRX suppressor and the latter a Q Short Chop. One thing worth noting is that with a supersonic round, you're still going to have a substantial report. The advantage of a suppressor, besides the hearing protection, is that the sound is distorted and diffused. I can't see a flow-through design effecting that, considering that the gasses are being ejected from the can radially.

The suppressor industry is getting a lot cooler as of late. I just bought the new Huxwrx Ventum since that thing just seems excellent all around. Flow through, removable core, etc. Seems excellent for any possible baffle strikes since cores aren’t serialized. Would be even cooler if you could swap different cores for different applications.

This channel always manages to put out a video related to what I’m thinking about buying.

good explanation enjoy it first time listening keep up the good works wiil be watching more

Are we just gonna act like all the big suppressor manufacturers weren't looking down on huxwrx and saying their silencers were gimmicks and then suddenly all the big players are making "Flow-Through" low back pressure suppressors and calling it their innovative idea because I remember. Where is surefire's new suppressor because they have been dormant on new designs forever and shitting on Huxwrx, a few years ago Doug Olson(Retired) from Knights Armament said in an interview that 3D printed suppressors were not the future and look at KAC now, B&T from Switzerland are gonna act like they invented all the baffle tech already used in most silencer yet they were caught copying KAC baffles in the 90s curtesy of HK giving them KAC suppressor tech used on their guns, they're probably also gonna claim they were doing the reduced back pressure cans for a long time before huxwrx.

Love my nomad L on my 9" 300 blk. Super quiet i was impressed

Huxwrx 762Ti ,the 1st test I did was to mount it on the Daniel Defense mk18 with that 10.3 barrel. MK18 way over gas from Factory. MK18 ran like a champ, no recoil that I can feel, no gas to the face. Only fired 3 Mags, but when I got home to clean the MK18, it was like I never fired any rounds suppressed.

Depends on the application. Flow through isn't always the best option with NV.

# repeale the NFA!!!!!!

I really would like to get a supressor, but I just don't trust the ATF not to go. "Na fam, we changed our mind. Turn in your thousand dollar piece of gear or become a felon."

Since suppressors are now legal to own without special permits beyond your gun-license in Sweden, and no tax-stamp, most hunters and sportshooters are getting them -- and we have local brands that manufacture great ones.

I haven't gotten into the suppressor thing yet. I am educating myself with videos like this. It didn't take long for me to have a favorite. I'm a fan of flow through. I'm waiting for the Texas suppressor case to get finalized to see what becomes available in my area. If I have to pay the $200, flow through. I literally moved from Las Vegas to Texas just because of the constitutional carry & Texas suppressor laws.

Very informative, thanks! I need to research to see if there is an ideal can for my 45-70 lever gun + .308 gas + .22 ARC bolt. I don't need 3 separate cans I'm sure but hoping I can find a decent general purpose one to fill the need across this wide array of calibers. I already own the Banish30 but the lever gun of course won't work with that. Keep up the great work you guys!

Only suppressed gun I ever shot was a Tavor... Didn't even get one mag through it and I could barely keep going... Now that owner has a Flow, and I'm interested to see if that changes it.

excellent vid, very helpful. thanks!

Nicely done video, learned a lot

I'd like to see you guys test out adjustable bcg's like the Sharps SAGRS with baffled suppressors. Also best buffer weights for different barrel lengths for 5.56 and .300aac

As far as “first suppressor” goes it’s hard to beat the Mystic X. It’s a great multi caliber jack of all trades like can. And if you decide later to get more niche specific cans than great you still have an awesome 9mm specific can with a lot of versatility.

First time seeing the new intro. Looks great!

Great video Anyway you can do a bolt action rifle surpressor video? Best for a bolt action? Quietest option? For a .223cal bolt gun.

Flow through is the new way to go. . .

It was never brought up ... and I am at the beginning of my suppressor journey ... What about baffle strikes? minimal impact with many suppressors as they have a "removable serial number" section.... Any knowledge to add OP's or Huxworks?

Good stuff guys!

Would a huxwrx flow 762 ti be a good fit for my LWRC m6ic di?

What's your take on adjustable bolt carrier groups like the Bootleg brand that can be adjusted with 4 settings?

Don't forget blast forwarders and so called linear compensators. I've had a lot of relief with larger gas gun rounds like 6mm arc, 6.5g etc using larger linear comps like the magnum KVP and badlands integrated muzzle break. . The large KVP acts like the first chamber of a silencer and the badlands has structures like a quasi flow through. Surely doesn't do as much as full on silencers but man, what a relief for me and fellow shooters vs many other muzzle devices such as flash hiders, muzzle breaks. Granted I'm not typically using an SBR but for 16" it is a huge help. Haven't asked the bucks down range what they thought of the noise but may some day.

How much of the first set of pros and cons apply to a bolt action instead of a gas gun?

I would love to see the huxworks 556k compared with the silencerco velos lbp can.

i wonder how the hux wrx suppressors would hold up and work in a ultra sonic cleaner with the correct solvent as its a 1 piece can and ultra sonic are know to clean quicker and easier

I absolutely couldn’t find any answers anywhere else for this question. So does the length of the suppressor add velocity to the barrel. For example: you have a mcx rattler 5.5 inches barrel in 556 chamber . If you put an 8 inches suppressor on, does the velocity output acts like you are shooting from a 13.5 = 8 + 5.5 inches barrel or it’s just the same as 5.5 inches barrel?

flow thru for if im using a semi auto or automatic gun, but if im using bolt action or single shot guns i prefer baffled

So if the sound at the mussel on a flow through is the same on as unsupressed then would a flow through be louder in an indoor home defense situation than a traditional can?

2questions To clean can you soak and use a ultrasonic cleaner? Can you use the 762 flowthrough for multiple calibers?

Which flow through suppressors would you recommend for 9mm handgun?

"How much are they?" "Well.. you know, you pay for the technology" ... best answer.

All of the still have a flash signature, shoot them in the dark and you’ll see the flash. Some cans do better than others. But still have a flash signature

Love the new intro

Wish you Guys could have had the Yankee Hill Machine YHM Fat Cat R9 , T3 on stage in this comparison , it's a short fat new design on the market. I think the Huxwrx gas forward flow through design is the best thing on the market today.

How about recoil difference between them ?

@ClassicFirearms what is the tall suppressor that Matt was wiping when the video started

I'm looking to get the yhm r9 it's welded baffles and all stainless construction along with price point and versatility for my vector, scorpion and 300 blackout has me convinced it's the one for me.

Im looking for a 7.62 ×39 flowthough for my zastava pap92. I sold my 85 because i dont see the point in short 5.56 pistols. I also need one for 300 blk when i finish my build, but i dont know if a universal can is worth it instead of dedicated. I would save a lot of money, but i want a shorter can, and they are all long. Any ideas?

You will have to tune subsonic loads to your set up or

Didn't know you guys had someone with LE experience working for you. Usually its Military people who honestly aren't that well versed in using weapons CONUS. If I ever go to the middle east I want to hear from Vets. Here state side I want to hear from a variety of LE (different locals, and feds).

Anyone know what form to fill out to purchase and which for to manufacture??

Very informative. Given everything that you guys said, the flow through suppressors are, by far, the better choice. The main selling point for me, is the superior wellbeing of the shooter, and the firearm itself. Any other considerations are secondary.

just bought the HUXWRX Flow 762 Ti yesterday. its gonna be a long wait

I am really new to suppressors. Thank you for a very informative video. However, I did notice that your display had different length suppressors. What affect does suppressor length have? Thank you again for an awesome video.

You can make a HBP can sound really good, and your gun run *RIGHT*, you just have to do more to regulate the gas drive of your gun. Piston guns actually reach a point where they seize up at the piston.... while simply adding lube to the carrier of a std AR literally remedies this issue across thousands of suppressed rounds.

So based on this info do you recommend a flow through for a 300 blackout 10.5” barrel that will be subsonic only?

Why is there no comprehensive parametric filter for suppressors? Silencershop has the start of one but even it is far from comprehensive. Theirs has no option to filter flow or non-flow types as an example of one of the missing categories.

Thanks!

WoW..! This is so simple, so easy to engineer but how hard are they to sale at 600.00 and up?

I have a 204 single shot ruger, can you make a suppressor so I don't have to dumb the bullet down

Question of what task the suppressor has to accomplish. In not civilian circles the operator wants a low signature, aka less sound transported to the threat. That way the target has more problems to identify the location of the shooter. Not ideal for the operator since pressure, gas and sound are more uncomfortable. Civilians want it exactly the other way around.

Is the barrel suppressor ruger 10/22 considered flow through? And mark pistols?

I wish they would have touched on the need for a booster for pistols and do you need a booster for pistol caliber carbines? I don't care about the heating/cooling. I want efficiency in noise suppression.

OSS/HW flow through, the end :)

I learned a lot.

Man I truly appreciate Matt's knowledge. This man must be protected at all costs.

I see no Griffin Armament M4SD II Suppressor, they came up with the flow threw in a way.

I have a X95 as my go to rifle....Its flow thru or nothing!😂😂😂

If you had a recommendation on what ar to get what would you suggest. Price isn’t much of an issue but I’m new to the ar scene and want a nice one. Was looking a Daniel defenses and the new sig spear but open to others

Pistol caliber or boltgun baffles. Selfloading rifle flowthrough

So which design is quieter?

You did not talk about mounting options.

Can I get the list of the flow through models in the caption?

Is there a suppressor that will work on 5.56 and on 308?

How y’all be getting those I won’t one

I'm a rookie when it comes to suppressors. I don't own any, yet. I'm taking in all the info to later decide what to buy. So keep it coming. all info is welcomed.

How much cost?

HuxWrx suppressor’s are full auto rated!

Slip 2000 in high school … lol good one

That's also why planes are also always clean, same with race cars.

So when can we expect to see a few hybrid options 😅 best of both worlds as it may be 🤔😉

flow through just means baffles for your baffles and non sealed front end

So is this an ad for a single company with a patent on it, while only offering it in 4-5 calibers?

Which is better on special operation lpvo or red dot?

In South Africa we have a lot of experience with suppressors on Bolt action Hunting rifles. First Major concern is weight and the second is recoil reduction. • We use silencers that go over the barrel (reflex) to bring the weight a bit closer to the pivot point. • You did not discuss Recoil reduction, and that is almost more important to South African shooters that the noise reduction.

9:10 Decibel to shooter's ear

Flow through from experience.

I think Kai was in the bureau of the small bus about firearms. Lol jk

Flow-through suppressors for me

None..why should I be the atf's sugar daddy 😂😂😂😂

Heat/IR signature?

Guys, you need to look up Bernoulli's Principle. A suppressor isn't trapping gasses in chambers to slow the gasses down. The suppressor is forcing the gas through a constriction to decrease pressure. Sound volume is directly related to pressure. The gasses aren't slowing down. they are actually speeding up

Surefire RC2 is the way for 5.56

Can y’all get Kaya a bigger shirt?

Why don’t y’all do anything about silerenco?

When getting a suppressor, weight is the #1 consideration you should keep in mind (sound suppression isn't a problem anymore). Go titanium whenever possible! ...As for a flow thru VS a traditional baffled suppressor, you should only get the flow thru if your rifle does NOT have an adjustable gas block; otherwise there is no downside to using a traditional baffled suppressor in a rifle that HAS an adjustable gas block.

Hi Guys. If you get a chance, ask HUXWRX if after cleaning with a solution, if blowing out the suppressor with a home garage style air compressor would cause any harm and if not could they come out with a threaded receiver plug to attach to the compressor hose. Just a thought about maintenance. 👍👍👍👍👍👍

Kaya sounds like he has his pilot's license when he talked about ice on an airplane wing.