Hi Shane I've found cleaning barrel now and again does improve my Springer but I only do it when it starts to shoot off a bit 👍

I always clean a brand new barrel because a lot of new guns have anti corrosion gunk inside to stop corrosion while shipped/stored. Only cean after that if accuracy drops off

With a new rifle or pistol I’ll pull through between 10-20 times before the bore is clean, amazing what comes out- then every 200 pellets - Napier pull through and power oil too! You need three Napier patches for .22 and two for .177 to do a good job!

Pull the pull through down about an inch then put a bit of spray down the barrel then pull you will get no gunge shit at the business end of the barrel so it won't matter if you use cheap wd 40. Looks like it did the job

A new rifle needs a clean to remove all the preservatives from the rifling grooves. Then clean only when you notice a decline in accuracy.

Hi Shane, cleaning barrels is a mute point, Matt Manning off the airgun show says he's never cleaned the barrels on his guns, and they say it takes at least a couple of hundred pellets to re lead them, I must admit I have never cleaned My barrels, and as far as I'm aware have had no problems.

Probably needs 30 or 40 shots to" lead in" again after a thorough cleaning.mine likes every type of pellet(7 up to now)great little budget gun.

Try the h&n field target pellets, Kral allegedly use them as a test pellet in the factory. I used to have the same gun and found the head size of the pellet(4.51) made a big difference. Ended up getting penny sized groups at 35yrds with qys streamlined heavy pellets in 4.49. Good luck with the testing.

If pellets are dirty why not clean them?

I followed the advice from Pellpax and used some fibre pellets and use one per tin. Air arm Diablo Field 8.44 give me shot on shot at 50 feet.

Yes please, remington next.

hi Shane try trying it without the silencer and with a different silencer as some pellets/rifles are silencer fussy . i know it sounds silly but its true . i would imagine you should be getting clover lea groups without a silencer and a pellet it likes then take it from there . i have riffles that wont entertain dome of my other riffles silencers . you also need to keep your silencers clean , then theres' a case of is the pellet clipping the silencer. in my experience the longer the silencer the more risk of clipping occurs due to tolerances in the threads and silencer adaptor fit , i loose fitting adaptor is a no-no if it slops around when the grub screws are loose it really needs packing with foil or tape equally around the whole barrel until the adaptor just slides on without any wobble, which should in theory at least true-up the adaptor which should intern true up the silencer or make it more central which improves consistency/accuracy .. food for thought Shane .

My NP02 sub 12 22cal loves Polymag shorts for ratting up to 25 yds, group opens up after that but if i use JSB then they are good to 30 yds. Barrel cleaned when new then haven't had to clean it after at least 2000 shots

Hi Shane, wash your pellets first before you do any shooting

you want to lead a barrel, it improves the seal on pellet. I'd try different pellet brands to improve accuracy, and then if necessary weigh pellets. I get less than 4 fps spread in 10 shots, with a chrono, with unwieghed pellets that suit my rifle.

Hi Shane, I clean my barrels every 150-250 pellets and it surprising how much muck comes out- it’s best not to use WD40 though as it eats O rings and creeps inside the interior of guns.

Shane i use the VFG cleaning felts, put two in and a pellet behind for a bit of resistance.

Hi Shane, top tip clean rifle upside down then no oil should get in transfer port and inside

Hi Shane just come across your channel so I don't know what you've tried or haven't,but the QYS pellets are supposed to be very clean,washed at the factory,bad point they are expensive,👍

Show muito bom parabéns.

Hi mate, try jsb 10.34 gn. I use these in my np02 work really well out to 53yrds

Good shooting shane you would do a rat or wood pigeon head with that group.

Hi Shane, great vids👍 What gun stand are you using?

Very informative video. What gun stand do you use?

Nice vid . Is that gun fussy on pellets ?

Bonjour mon ami je suis très fier pour toi car pour ta santé le pcp est fait pour toi et évite beaucoup de fatigue très beaux cartons tu est sur la bonne voie très cordialement jpb (prend bien soin de ta santé) un papy de Normandie !!

Had one of those napier kits until the little loop broke, made a replacement out of strimmer wire. Instruction on utube.

I’ve booked a table at the greyhound on the 9th about 3 , I’ll look out for you mate ❤ , why do people clean the barrel then fire a few hundred out before checking out the statistics again 😂

Hi Shane. Could it be that the barrel is dirty because you've been putting dirty pellets through it.

One mistake you made was you left the gun in fire you should put safety on 1st before you cock it and cleaned it not having ago but safety 1st 👍

No way would I use that for hunting maybe rats at sub 20yards but I wouldnt have much confidence in it, its either very pellet fussy or its at its capacity.

Don't like those pellets at all, try H&N or Air Arms Diabolo.

Try different pellets