Cleanest Built Pixhawk 2.4.8 Drone | F450 frame
Рет қаралды 61,508
4 жыл бұрынThis is the cleanest made drone by me. In this video, I will show you the wire management and component techniques. This drone uses a PixHawk Flight Controller which is a open source controller by ardupilot or apm. it alsl uses a neo 8m gps module with 3dr power module and 433 mhz telemetry. it can be used with a mobile application called q ground control. motors used here are readytosky 980 kv motors with dji white propellers. it uses a orange lipo battery. its build around a f450 frame.
Amazon India
Arduino UNO R3 - amzn.to/2n8NbWi
Ultrasonic Sensor hc-sr04 - amzn.to/2ACHEkl
Arduino Beginners kit - amzn.to/2n6LUPj
Wi-Fi Wireless Transceiver Module for IOT ESP8266 - amzn.to/2M0ttd8
NodeMcu WiFi Development Board - ESP8266 - amzn.to/2LOQgtd
Bluetooth Transceiver Module - amzn.to/2M077sj
37 in 1 Sensor Modules Kit for Arduino - amzn.to/2vysGpA
Servo Motors 2 - amzn.to/2AEeJMO
Arduino Nano V3 with USB Cable - amzn.to/2vxcxRo
Quadcopter Kit Quad Copter - amzn.to/2ADuzqS
Social Links
Facebook - robocircuits
Instagram - / robocircuits
Twitter - / robocircuits
Instructables - www.instructables.com/member/...
Arduino - create.arduino.cc/projecthub/...
@Merc-Rover 2 жыл бұрын
Flamewheels have been around for years and it's great to see them still being used.
@RoboCircuits 2 жыл бұрын
Yes
@kuldipAerotek 9 ай бұрын
I think this is the first step that the drone aspirants would get help
@RoboCircuits 9 ай бұрын
yes...
@marshallallen80 3 жыл бұрын
Thank you so much. One shot in your video Solved my problem.
@RoboCircuits 3 жыл бұрын
Welcome
@RoboCircuits 2 жыл бұрын
Which shot????
@marshallallen80 2 жыл бұрын
@@RoboCircuits I don’t remember exactly. I’m pretty sure that it was a clue regarding the arm switch and ESC calibration. It was something small but critical. Your video was so clear that I could see the issue.
@quattrotz9367 Жыл бұрын
Nice and clean setup. I like the wiring order
@RoboCircuits Жыл бұрын
Thanks!
@ricardpozo5023 Ай бұрын
hello, where on the drone did you put the radio receiver and the battery? by the way, great video!
@electronic7979 4 жыл бұрын
Very good 👍
@RoboCircuits 4 жыл бұрын
Thank you
@supercobrapro7470 3 жыл бұрын
what's the difference between this and Pixhawk Pro version?
@maxkl654 3 жыл бұрын
Did the controller board manage with all the peripherals? Some report issues with this model
@RoboCircuits 3 жыл бұрын
It is made to handle all... No problem at all
@mohammednaved1973 3 жыл бұрын
For pixhawk 2.4.8, which firmware did you select in ardupilot list. Pixhawk 1, cubeblack, pixhawk 1-1m or something else? Please let me know.
@RoboCircuits 3 жыл бұрын
i don't remember but i choose the latest stable one.
@coveben959 4 жыл бұрын
amazing viedo but please can you make the configuration video please ? im stuck in the part of telemetry (the usb stick)
@RoboCircuits 4 жыл бұрын
Okay sure
@cibhiadhinath2759 11 ай бұрын
Never keep the pixhawk next to power cables , it will affect the magnetometer and also use a damper while mounting the pixhawk for a stable flight.
@RoboCircuits 11 ай бұрын
Thank you for pointing out
@deepakcoolm 2 жыл бұрын
Bro where did you buy that battery holder rods? And how much is the battery size u have and how much fly time you get ?
@RoboCircuits 2 жыл бұрын
Battery size is 1100 mah... It flies 5-7 minutes only. Battery holder sticks are known as standoffs these are basically threaded rods. You can find them online
@deepakcoolm 2 жыл бұрын
Nice video to build clean.. BTW, we can also use glue gun to avoid short circuit..
@RoboCircuits 2 жыл бұрын
Yes you can
@Tuonghuyha 3 жыл бұрын
how did you configure the motors in the QGround? what is the RX output mode you used?
@RoboCircuits 3 жыл бұрын
Configure it using reciever
@RoboCircuits 3 жыл бұрын
Pwm for apm .... Sbus for pixhawk
@sala7311 4 жыл бұрын
2:12 , Is it safe to connect all 4 ESC to pixhawk just like that, I read in an article that only ESC with power supply must be connected to pixhawk, the remaining ESC power supply wires must be cut off and then connected, Is that true?
@RoboCircuits 4 жыл бұрын
No its not important. If power is given through power module then esc power gets automatically cut
@GAURAVSHAH12 7 сағат бұрын
bina battery ka uda diya ?
@whitecomet1892 2 ай бұрын
16:00 wow
@RoboCircuits Ай бұрын
Thanks
@shefqetlulja8511 2 жыл бұрын
In my quadcopter i get randomly EKF ground mag anomaly(very danger cause copter acting wired), should i recalibrate it even that the pixhawk has a global magnitude database and no need for compass calibration they said
@RoboCircuits 2 жыл бұрын
You should recalibrate it. Even i had a problem when the compass was working fine on the ground but while testing it was acting weirdly. Most modules are made in china and many have hardware issues. So better to check it first
@arijitbiswas4448 3 жыл бұрын
Hi. I am trying to build a quad with same config, but in mission planner software during radio callibration, there is no signal in the respective channels. Can you help me. Thanks
@RoboCircuits 3 жыл бұрын
are you using a sbus reciever?
@deepakcoolm 2 жыл бұрын
hi bro.. nice video.. I too have this Pixhawk kit. BTW, you didnt add the PPM encoder to your drone. Is it not required or its mandatory? I have flysky transmitter and receiver. Any comments appreciated
@RoboCircuits 2 жыл бұрын
If you have a ppm receiver then you don't need ppm encoder.
@deepakcoolm 2 жыл бұрын
@@RoboCircuits thanks for your response. My flysky fs-ia10 receiver has PPM (as mentioned in the label)
@RoboCircuits 2 жыл бұрын
Then it will work
@ankithbachhu9124 4 жыл бұрын
Im trying to build a drone similar to this. Will this same build work if I add a raspberry pi
@RoboCircuits 4 жыл бұрын
Yes
@bryntotah9552 Жыл бұрын
Hi, I am figuring out what DIY kit to buy. Where did you buy this kit?
@RoboCircuits Жыл бұрын
Robokits.co.in
@asbjchk 3 жыл бұрын
I'm planning to build one too, how different the performance do you feel when compared to those DJI / ?
@RoboCircuits 3 жыл бұрын
DJI is better
@dustinjamal8689 2 жыл бұрын
i guess I'm kinda off topic but do anyone know a good website to watch newly released tv shows online ?
@muhammadrocco5709 2 жыл бұрын
@Dustin Jamal flixportal :)
@dustinjamal8689 2 жыл бұрын
@Muhammad Rocco thank you, signed up and it seems like a nice service =) I appreciate it!!
@muhammadrocco5709 2 жыл бұрын
@Dustin Jamal happy to help :)
@Tuonghuyha 3 жыл бұрын
how did you set up the telemetry radio for this?
@RoboCircuits 3 жыл бұрын
Using ardupilot
@ajayprakash5482 Жыл бұрын
Sir i have a problem in radio calibration when i turn on transmitter it is not showing on mission planner
@RoboCircuits Жыл бұрын
Did you bind the receiver to the transmitter????
@shaan29888 3 жыл бұрын
Sir. Programming video upload please
@piramid53 3 жыл бұрын
what is your control ? remote control or labtop by mission planer program
@RoboCircuits 3 жыл бұрын
Both... Remote and mission planner
@justinboth2684 3 жыл бұрын
how u calibrate the esc with ardupilot ? and how about the setting of radio control ?
@RoboCircuits 3 жыл бұрын
Calibrate it using your reciever...
@justinboth2684 3 жыл бұрын
@@RoboCircuits could i got your tutorials about that , please.
@RoboCircuits 3 жыл бұрын
Sure Soon
@connorjohnson2831 4 жыл бұрын
I'm actually in the middle of a very similar build to this. I'm trying to decide on battery size. What battery did you use, and what is the flight time you get? Thanks
@RoboCircuits 4 жыл бұрын
This one is 3400 mah... Flight time 15-17 min
@creativemind4165 2 жыл бұрын
hello dear, i make quadcoptor using pixhawk microcontroller with gps and fsi6 remote control , in my drone when i armed drone and throttle up then motors are rotating with different speed. i calibrate esc again and again still same problem happening. what i shoud do ? help to solve this problem. please.
@RoboCircuits 2 жыл бұрын
Calibrate accelerometer and check motor number and rotation properly
@jinchengau4225 3 жыл бұрын
Is the Pixhawk 2.4.8 still support? or should I opt for Pixhawk 4 for project purpose
@RoboCircuits 3 жыл бұрын
Yes it supports
@RoboCircuits 3 жыл бұрын
Pixhawk 4 is awesome... If you can go for px4
@talhamaster8550 3 жыл бұрын
Ready to sky motors from were u got
@RoboCircuits 3 жыл бұрын
Robokits.co.in
@Tuonghuyha 3 жыл бұрын
so i built the drone with the exact same components like you had. Apparently, when it comes to test fly for the drone, my drone couldn't take off. when i move the throttle, the drone is kinda flipped. it looks like to me that the drone is not in balance. do you you what the issue here of the drone?
@RoboCircuits 3 жыл бұрын
Whatsapp your drone pictures to me on whatsapp 8813083500
@puttalewis 3 жыл бұрын
ake sure ur fan blades / propellers are installed in the right direction
@Tuonghuyha 3 жыл бұрын
@@puttalewis yea that was the issue explained why the drone couldnt take off. thank you
@zlatanzlatan7361 2 жыл бұрын
@@RoboCircuits Hi. What is your country dialing code? Help me please
@sun.madeshwaran 2 жыл бұрын
@@zlatanzlatan7361 +91
@HieuNguyen-yt4sc 4 жыл бұрын
Can I setup RC without 433mhz telemetry?
@RoboCircuits 4 жыл бұрын
With usb cable
@SudiptaMandalsuri 3 жыл бұрын
how did you carry it in your backpack?
@RoboCircuits 3 жыл бұрын
Hehehe I carry it in my hands
@tharunjavalimn 3 жыл бұрын
Hi I recently purchased pixhawk 2.4.8 and a hexa frame S550. I am facing some problem with it. Please help me 1. Main out 3 of pixhawk seems to be the problem. Whatever ESC I connect I am not able to spin motor. But with other Main out's I am able to spin. What could be the problem here? How do I resolve? I had flashed Hexa firmware, Octo firmware and quad firmware. None of these firmware worked for me on main out 3 . But main out 3 was working fine before. 2. As I am not able to use main out 3, I had to flash octo firmware for the pixhawk on my hexa frame. So , I could use main out 7 and able to spin the motor. Now I am able to arm the drone. But when I try fly , it leans or drifts towards left side. I am not able to control it and I have damaged my hexa frame. I am using FSi6 transmitter. Do I have to trim? or Do I have to calibrate comapsss. How do I handle levelling issue? Please help me.
@RoboCircuits 3 жыл бұрын
Join me through whatsapp
@tharunjavalimn 3 жыл бұрын
@@RoboCircuits I could finally fix the problem and fly the drone smoothly. Thanks for your support and help
@dronauticaltech-fun3485 3 жыл бұрын
Bro please use a shock absorber under the Pixhawk.
@RoboCircuits 3 жыл бұрын
I used 3 layers of double sided tape... It acts as a shock absorber
@emrebulut4495 3 жыл бұрын
@@RoboCircuits Was it enough? I was also hesitant to buy a shock absorber.
@michaeldupreez5341 4 жыл бұрын
Hello, I have built a drone using the Pixhawk 2.4.8 and am having issues with the final touches of it. I cannot get the motors to spin above 5 or 10 % even if I turn the throttle all the way up. I am using Mission Planner. I would really appreciate any advice or assistance you could give me. Thanks.
@RoboCircuits 4 жыл бұрын
You have to arm it
@RoboCircuits 4 жыл бұрын
Before flight Drone must be armed
@RoboCircuits 4 жыл бұрын
Check how to arm a pixhawk
@MrNams 3 жыл бұрын
I have “Pixhawk 2.4.7 PX4”, when I go to “Mission Planner 1.3.74” then I see there are two option to Install Hardware 1) Install Firmware -It has all Firmware Named as “Copter…” When I select “Copter 4.0.5 Official” then It ask for Platform,Version and Firmware. 2) Install Firmware Legacy - It has all Firmware Named as “ArduCopter…” I am confused how to proceed to setup my “Pixhawk 2.4.7 PX4”. Please help.
@RoboCircuits 3 жыл бұрын
Select platform as pixhawk Version latest stable firmware
@MrNams 3 жыл бұрын
@@RoboCircuits you mean pixhawk 1?
@RoboCircuits 3 жыл бұрын
No pixhawk 2.4.8
@MrNams 3 жыл бұрын
Unfortunately I could not calibrate ESCs even after lot of search, so I have installed PX4 latest firmware.
@creativemind4165 2 жыл бұрын
hello sir. i make quadcoptor using pixhawk flight controller. in my drone goes only one direction and it not takeoff properly. can you halp me ?
@RoboCircuits 2 жыл бұрын
Message me on instagram. I will guide you there
@creativemind4165 2 жыл бұрын
@@RoboCircuits ok
@shaan29888 2 жыл бұрын
Bro my drone fly only right side. Transmitter throttle up drone fly right side
@RoboCircuits 2 жыл бұрын
Your calibration is not proper. 1. Calibrate motors properly 2. Calibrate gyro properly 3. Make sure all motors are at correct positions and correct motor numbers 4. Make sure flight controller is at exact Center and facing forward
@animechannel8584 3 жыл бұрын
What is difference between pixhawk 2.4.8, 2.4.7, 2.4.6, 2.4.5 ???
@RoboCircuits 3 жыл бұрын
its device versions.... company constantly improve its product so they keep on releasing different versions
@user-or3or1un8g 4 жыл бұрын
can we power Pixhawk from BEC of ESC?
@coveben959 4 жыл бұрын
this is the circuit power of the pixhawk es.aliexpress.com/item/32960292856.html?spm=a2g0o.productlist.0.0.2561561a4nvOrH&algo_pvid=5822b3b9-18c6-4151-acbe-4ac0d13c0085&algo_expid=5822b3b9-18c6-4151-acbe-4ac0d13c0085-0&btsid=0ab6fa7b15916713722368611e5dfb&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
@RoboCircuits 4 жыл бұрын
You have to use a power module
@user-or3or1un8g 4 жыл бұрын
@@RoboCircuits ty for answer
@jvlogs7917 3 жыл бұрын
did u register the drone ?
@RoboCircuits 3 жыл бұрын
No
@gagandeep1714 3 жыл бұрын
sir i made a drone using kk2.1.5 , now i am planning to use other flight controller . with which flight controller should i start with apm2.8 or pixhawk can you please guide me
@RoboCircuits 3 жыл бұрын
Pixhawk is good
@aredits7311 Жыл бұрын
Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk
@RoboCircuits Жыл бұрын
Place the flight controller in exact centre of the drone… make sure it is levelled and pointing in right position…. Calibrate gyro properly. If you have gps use a gps stand.
@aredits7311 Жыл бұрын
@@RoboCircuits i have done many times properly but facing the Same issue
@aredits7311 Жыл бұрын
@@RoboCircuits how can i contact you bro ??
@RoboCircuits Жыл бұрын
Send pictures on my email
@RoboCircuits Жыл бұрын
Or instagram
@droneguy69 2 жыл бұрын
What's your PID settings?
@RoboCircuits 2 жыл бұрын
Automatically set by the software
@droneguy69 2 жыл бұрын
Mine just shot 50' up in the air and couldn't control it. Then it landed on its own.
@vijayanalsubramaniam3696 10 ай бұрын
Bro can give circuit diagram for this pls
@RoboCircuits 9 ай бұрын
search for pixhawk circuit diagram
@umangkalra8212 3 жыл бұрын
Dude, anti-vibration mount to use kr leta. Vibration damping ke bina Pixhawk control lose kr deta hai. Kitni baar mera quad crash ho chuka hai!
@RoboCircuits 3 жыл бұрын
i used 4 layers of double sided tape
@abhicutelaugh 2 жыл бұрын
whats difference between pixhawk 2.4.8 vs pixhawk 4?
@RoboCircuits 2 жыл бұрын
Pixhawk 4 is powerful and runs new firmware
@abhicutelaugh 2 жыл бұрын
@@RoboCircuits do you mind sharing the url for pixhawk along with the Adriano stuff shared in your description?
@RoboCircuits 2 жыл бұрын
Check my website robocircuits.com .. you can google "pixhawk robocircuits.com" to find articles
@vnagaravi 3 жыл бұрын
Can you upload your parameter file i need mine not working
@RoboCircuits 3 жыл бұрын
sorry i dont have that right now
@arpitofficial7653 3 жыл бұрын
What is flight time
@RoboCircuits 3 жыл бұрын
12 min
@arpitofficial7653 3 жыл бұрын
How to increase the flight time
@spotdoit6047 4 жыл бұрын
What about previous project about dji frame drone.
@RoboCircuits 4 жыл бұрын
That is another project That will be completed slowly
@spotdoit6047 4 жыл бұрын
Ok, but try to make that fast because this all are gets common today, try to make them different.
@sz72909 4 жыл бұрын
Useless!! No sound, no explanation!!
SKYWARD DYNAMICS
Рет қаралды 20 М.
Joop Brokking
Рет қаралды 103 М.
Viral Science - The home of Creativity
Рет қаралды 424 М.
Beginner's Tutorial: 2KG Pixhawk Drone - Assembly, Integration, Flight Testing & Basic Tuning #drone
Karthik's Tech Time
Рет қаралды 7 М.