View the steps to install a ShelfTrack closet system.
Пікірлер: 223
@Madebyjustina4 жыл бұрын
This lady makes it look so easy and I’m over here covered in drywall dust and desperation 😔
@londonthebaddest4 жыл бұрын
Justina • im cryinggggg😂😂😂😂😂😂
@Jusderrick3 жыл бұрын
London Kennedy 😂😂
@1985cheryl3 жыл бұрын
😭😭😭😢
@mikkot.47583 жыл бұрын
I feel you on that drywall dust!!!!😅😅😅
@nosirrahm3 жыл бұрын
She gave me hope that I could do it myself. I haven’t even figured out the layout yet. ☺️
@Thanatoast2509 жыл бұрын
Note to buyers: the Shelf Toggles on the back say "drill a .25" hole" instead of 1/2 inch hole. Be sure to use the 1/2 inch, not the .25 inch, or else the toggle will not fit! Learned this the hard way!
@freelow32663 жыл бұрын
Nice. Thanks a lot
@ds79003 жыл бұрын
When installing the standards onto hollow wall, use 3/16" x 3" toggle bolts. The 3" bolts will be long enough for the toggle to catch the other side of the wall. It will make securing the standards a breeze.
@goingnuclear7265 Жыл бұрын
I had to make trips because this video sucked
@josetteskinner4200 Жыл бұрын
@@ds7900 Thanks for the advice. For some strange reason I seem to have a crap load of bags of those toggles 😅. Glad I can finally put them to use.
@TranTheClever4 жыл бұрын
Great job! Been looking for a better garage storage system! I think I'm going to go with this on at least two walls! Thanks for sharing your project! 5:32
@cosmiccowboy18 жыл бұрын
I like this Closet System...I installed 2 in my friends Apt. Rental...She didn't use a level the Hang Tracks? I used Blue Painters Tape to map out the inside closet wall to see how the closet system would look when complete...A second benefit is the ability to make marks on the Blue Painters Tape, then screwed the metal directly brackets directly over the tape, and remove the pieces most of them were invisible so i just left them hidden....good tutorial!
@MsNameGoesHere7 жыл бұрын
The tape trick is brilliant!! Thank you for commenting this :)
@myobinc7 жыл бұрын
Closetmaid impressions
@MukeshKumar-ji4lr6 жыл бұрын
im4coupons es ez an am
@ClosetMaidOfficial6 жыл бұрын
Thank you.
@aTechnicalFriend5 жыл бұрын
The Tape Trick - I wish I'd heard this about 30 minutes ago..... but I'll keep it for the future. You - deserve to win the ENTIRE Internet for this idea! Or a Nobel Prize! BRILLIANT!
@TranTheClever4 жыл бұрын
Loooooove this one! If you ever have to do more drilling through thick wood like that they have a bit called a hole saw which basically cuts out a cookie of wood! Blew my mind when I found out that exists. 😂 1:15
@dmccalldds3 жыл бұрын
My advice when installing by the HangTrack is to hold up the HangTrack with a level and best guess your location, and mark your holes. Put the track and level down and punch through each with a very small bit. If the drill falls though, it’ll need a toggle bolt, so mark that hole with a “V”. Drill 1/2” holes where you marked Vs, install the bracket with the bolts, and tighten as you keep the bracket level and fine tune height. THEN drill your holes that will be in studs. Stud finders aren’t totally accurate, and this method keeps you level and drilling minimally.
@martinzenk4504 Жыл бұрын
My toggle bolts are not quite fitting through the 1/2" hole, does it need to be forced through?
@montrayehoward11446 ай бұрын
Great advice !!! Ty
@dmccalldds6 ай бұрын
Sorry, Martin. I didn’t see this. I usually have to tap the toggles through with a hammer. Those corners always bind on that circular hole!
@chanteljohnson8934 Жыл бұрын
Started small with re-doing my coat closet. A few minor miscalculations that had me exchanging racks but I’m happy
@elimelechs.l32465 жыл бұрын
OMG I love this idea for my house
@Prettypeachtulips4 жыл бұрын
She makes it look so easy and it's not. The toggle bolts were a f'n pain in the ass. I did have 2 studs but they were not aligned with the pre drilled holes on the main hang bar, so I had to drill my own holes. I used 3/16 toggles with 3" screws. For those that said the screws just keep spinning...you have to pull the screw with your free hand while screwing it in. Pain in the ass...took me 4 hours.
@erinbrooke15783 жыл бұрын
I was wondering how the heck I was supposed to tighten the screws! I though about doing this and came to the comments to see if anyone else tried first lol
@chrystalsnow1453 жыл бұрын
Excellent video! I need these shelves to replace my shelves I have. My old shelves used for a pantry made of wood bent from the heavy weight of cans... I want to know if these shelves are sturdy enough for a huge pantry?
@marinadesantis29147 жыл бұрын
Thank you so much for sharing your video, now I know what to do. god bless you kind lady
@repmiamiprojectpat8 жыл бұрын
Pretty simple thank you
@simonollivierre9475 Жыл бұрын
Thank you lady , you made look so easy
@EsEN1013 жыл бұрын
I promise you people. It’s not this easy
@RatedAwesome213 жыл бұрын
it really isn't. how did yours go? did you screw in all the holes on the standard, or did you just do the top and bottom?
@TaylorGreenlittlemissmuffet2 ай бұрын
Yo facts 😂 it’s been 90 min and I’m still at her 1 min mark
@pogoli8 жыл бұрын
A 36" shelf (2283) that comes with exactly 2 brackets can only be mounted on two standards. In order for each standard to be no more than 4" from the end, the spacing of the two standards must be at least 28" apart. According to this video, the maximum distance between standards can be no greater than 24". Now either the 36" shelf comes packaged with 1 less bracket than required to meet their mounting specifications, or their mounting specifications are not correct.
@JazzoRenee11 жыл бұрын
You know what sucks, when the directions instruct you to drill a 3/8 hole for the toggle anchor insertion and the youtube video uses a 1/2 drill bit. Closetmaid needs to fix their direction.
@rbaraj3 жыл бұрын
Thanks for the heads up
@lesmith273 жыл бұрын
I learned the same thing after just buying a 1/2 in drill bit! Thankfully I haven't opened it yet!
@misskellyngo2 жыл бұрын
Which one is the correct hole? I just tried a 3/8 hole and my toggle doesn’t fit
@Sigmagod417 Жыл бұрын
Wow she make me very happy i was worried about how to install ❤️❤️❤️❤️❤️❤️❤️❤️❤️
@FranciaMichelle11 жыл бұрын
Just put one up using this video. :) It looks nice!
@Kentacus4 жыл бұрын
I avoided the shelf track and toggle bolts altogether. Install the standards over studs directly (there is a stud ever 16" or 24") Reduce your cost and increase the strength.
@djxxxplicit4 жыл бұрын
Was exactly what I was thinking.
@ricknelms4 жыл бұрын
Yes i thought the thing that would be emphasized would be attach the standards to studs?
@Kentacus4 жыл бұрын
@@ricknelms Why emphasize that you don't actually need something if you are just going to make money off it lol. This was designed for closets that the studs just landed in the wrong spot and you need some sort option to spread out the weight.
@tonadickerson3873 жыл бұрын
Great idea. I am going to do this.
@draycotthooke98963 жыл бұрын
I agree with eliminating the shelf track, except that if you use the shelf track, you only have to level that one piece. The standards all hang off of that leveled piece and your shelves will all be level. If you don’t use the shelf track, each standard has to be level and inline with the others. You can do it, but you have to be careful.
@andrewvorwald93732 жыл бұрын
This video is values making the job look easy over actually being instructional. If you install the drywall toggle like she does, your shelf will fall out the drywall as soon as you put weight on it. KZfaq "drywall toggle" for useful information on installing that type of drywall mount.
@andrewvorwald93732 жыл бұрын
Better yet, use the included drywall brackets. A toggle can be overkill.
@dilciaenid579 жыл бұрын
My order didn't include the hang track. How come?
@ermac9647 Жыл бұрын
Nice!! done and done!! 👏🏿
@lisahochman49362 жыл бұрын
Just to be clear--if the studs are not 16 inches apart on center, and I anticipate a problem using the horizontal piece, I can simply use the vertical bars (hitting the studs), right??
@meltmyfaceoff5 жыл бұрын
Um thanks Megan for showing me how to install my closets
@raflessia0711 жыл бұрын
i wanna try it.. i must get from hardware shop rite...
@mlm3982 жыл бұрын
I installed my wife's closetmaid with the screw nut wings amazinggggg 💪, but custom
@turbo_stryker2124 күн бұрын
I’m just trying to figure out why the hang tracks and shelving aren’t uniform lengths. Why do they sell a 72” shelf with an 80” hang track? That 8” of open hang track space drives me crazy. Why not make everything in uniform intervals of 12”? Why couldn’t they make the lengths 72” or 84”? The Rubbermaid FastTrack system does even 12” intervals but it’s literally double the price.
@KEVINfromCALI3 жыл бұрын
What is the load capacity of these shelves? I’m thinking of getting them for my closet pantry
@chrystalsnow1453 жыл бұрын
Yes I need to know also - for a pantry with heavy food, cans...
@jimsterling9357 Жыл бұрын
@@chrystalsnow145 Have used 'em in the pantry for =YEARS= with lots of canned goods and weight. No problem!
@drichardson0078 жыл бұрын
I just put a large shelf in. Thank goodness there were multiple studs to drill into. 50% of the toggles never worked and just "spin and spin" on the other side of the dry wall. I saw another video which recommended not to use them. Now I see why. Long story short, my shelf won't be holding any heavy items with only 50% of the screws actually anchored to something... :-/
@jaredrastoka7367 жыл бұрын
You have to pull the toggles towards the drywall and then tighten.
@aarontalili41617 жыл бұрын
hahahaha!!!
@bmorehemi3927 жыл бұрын
The toggles should never spin and spin...they're not designed to do so...you did something wrong
@df44802 ай бұрын
I took this shit my wife bought back to the store!
@rlanza10548 жыл бұрын
Hi, I just finished installing two 6 foot by 20 inch depth shelving units, purchased from Home Depot. I had been shopping around for some inexpensive shelving since I am a borderline Hoarder. I need to get my stuff off the floor in two rooms that I can no longer walk into. The choices were Closet Maid or this other brand. I selected Closet Maid because it was much more affordable for me. I installed two 6 by 20 inch shelves in two separate rooms. I used 5 vertical wall mount tracks on each, spacing them 18 inches apart. That made it safely within the required 24 maximum spacing, which was on the information display at Home Depot. The center Wall Mount tracks (or the 3rd track) was placed at 36 inches, half of the the 72 inches of the entire shelf unit (the 6 foot shelf). However, since these horizontal brackets that actually hold up the shelves are made of very thin metal tin, I'm concerned about how much weight these shelf's can hold? In all of the in-store information displays there is no listing of maximum weight restrictions. I even asked the store employee at Home Depot who is responsible for the shelving department at Home Depot. I asked him if placing the vertical brackets well within the 24 inch restriction; mine being 18 inches, could the shelf hold my entire weight across the shelf. I'm 185 pounds. He said, YES! But I noticed that these horizontal brackets are bendable by even my own hand strength? So can someone please tell me what the weight restrictions are? I am confident that the vertical wall tracks are not going to come off the walls. But I'm not so confident on these thin horizontal brackets can actually hold up the shelves if too much weight is placed on them. The other brand that I did look at as well seems to be made of higher quality metal and is much stronger. I now and uncertain if I made a mistake in purchasing Closet Maid for my particular needs. I have invested so far about $600 in these two rooms with Closet Maid. Thank you for your comments and information so I can be safe in using what I've already invested in and all the work to getting them installed. Rob
@vanessasrikantham12298 жыл бұрын
The instructions on your drywall mounting hardware say to drill a 0.25 hole. Please correct.
@brian163utube8 жыл бұрын
+Vanessa Srikantham I laughed out loud when I saw this comment. I just noticed the same thing an hour ago. No way your getting a 3/16 " toggle bolt through a 1/4 " hole. It should be 0.50 (1/2 " ).
@jrosalia7 ай бұрын
Would I be correct to say that once the hang tracks are installed, the rest of the closet system can be reconfigured or changed around at anytime? If do, I think I like this option best for my bedroom closet
@brentw86657 ай бұрын
You are correct
@jrosalia7 ай бұрын
@@brentw8665 thank you
@archy39013 жыл бұрын
I wish you could come and decorate my new house ❤️🥺
@shanairodriguez83454 жыл бұрын
1:33 ? How did she add those standards? It seems like she just clipped them in
@eshelton294 жыл бұрын
That's what I want to know! Are there "add on" standards?
@jeaniebrandt88236 жыл бұрын
Is it a requirement to have to install the hang track? Or is it really just for leveling?
@ClosetMaidOfficial6 жыл бұрын
Yes, the Hang Track is required and you hang the vertical standards from it.
@shahidchefofficial9144 жыл бұрын
Hello jeanie
@hollyfyy6 жыл бұрын
I like how easy it is to install but I don’t like it have gaps between both ends of the shelf and wall. It is a waste of space and stuffs tends to falls off.
@neekneek917710 жыл бұрын
Ima try this
@Neanie_804 жыл бұрын
This toggle bs is not working for me so now I have a big hole in my wall thanks Megan
@emcallah4 жыл бұрын
Same with me, only it’s 5 holes :(
@callancueva3 жыл бұрын
The video says to drill 1 screw into the center of each standard, but the ClosetMaid hardware says to drill a screw into EVERY hole on each standard. So now I need more hardware. Back to the store...
@dianem12894 жыл бұрын
So i just finished but half my toggles are loose. Any suggestions? Do i have to do this all over again and just do studs?
@emcallah4 жыл бұрын
Sounds like I’m running into the same issue!
@Kentacus4 жыл бұрын
@@emcallah @Diane Marcus The issue with toggle bolts is that the toggle is just spinning behind the drywall. You have to apply some pressure on the track for the toggle to "Catch." Pull hard on the track or slip a thin pry bar behind the track to apply pressure as you continue to screw the bolts in. This video might make my comments make more sense. kzfaq.info/get/bejne/npqoha2eqLandKc.html
@dancingbigguy3247 жыл бұрын
Easy. Unless you have to cut the 80" hang track from both ends. And the suggestion is to use a hack saw. So you can be hand sawing until the next day. How about Closetmaid show customers an example of cutting their products to size, because after all; it's about customization, right? And not just cutting the wire/ventilated racks with bolt cutters. Show a DEMO CUTTING the hang track and the verticals. Otherwise, the installation itself is very easy.
@lindashankle96456 жыл бұрын
Dancing Big Guy if you know how long you want each shelf, purchase the long shelf and Home Depot and Lowes will measure and cut for you for no charge. Just be sure to purchase the end caps for the raw edges. The "young" "muscless" lady at Home depot cut my 8ft rack making me 2 3ft racks and one 2ft rack. No hack saw needed. She used an electric clipper. Excellent video.
@bigmike50035 жыл бұрын
I cut down a 40 inch hang track to 36 inches taking two inches off each side. It really isn't that bad, I used a cheap plastic miter box screwed into my cheapo work bench and clamped the hang track to the box and went at it with the hacksaw. If anything it was actually easier than cutting down the 16 or 20 inch shelving units! I had them cut at the store but needed to take a couple inches off of a few and that was more of a pain in the butt holding those down.
@bigmike50035 жыл бұрын
He's talking about the top hang track or the upright standards not the shelving itself. I don't think the store will cut a track or standard for you.
@Nwadiogo2 жыл бұрын
@@bigmike5003 Lowe’s and Home Depot did not cut the hang track for me BUT I did find an Ace location that did (for a fee).
@brandoncluff66966 жыл бұрын
The manual was horrible. This video was awesome!
@jerrycampbell74272 жыл бұрын
100% accurate
@drrkishore34176 жыл бұрын
I need this installations
@marthab76211 жыл бұрын
I'm getting one... thanks, closetmaid.....
@rahilkaloo8555 жыл бұрын
What is price for six feet with 12 inch width where to buy
@gohstprncss8 жыл бұрын
These toggles absolutely suck. They all fell behind my wall as I tried to screw them in. Now I have 1/2 holes in my wall and no way to hang my shelf. YAAAY.
@AmericanBadAss9018 жыл бұрын
Need me to come over and give you a hand?
@athullyapresannan79747 жыл бұрын
Raging Machine j
@WVgirl1959 Жыл бұрын
She first has the shelf with the lip up, and then the next part shows the lip down when she adds the pole hangers. Preference? I know that I have them in different ways, in different parts of the house.
@garymorris4410 жыл бұрын
In the video she is using 3/16 size toggles which requires a 1/2 drill bit for proper hole sizing. The screw length are 3" - ClosetMaid Part#2877
@Superj3439 жыл бұрын
Thank you!
@misskellyngo2 жыл бұрын
!!! This. The instructions say 3/8 holes and the toggles don’t fit with that
@princeopoku5846 Жыл бұрын
Thanks .
@marioreyes7311Ай бұрын
What if I cannot put it on any stud? Because of the size where I want to use it a cannot reach any stud..
@carlinamercedessanchez38313 жыл бұрын
Disculpa me pueden informar si en Colombia Bucaramanga las podría encontrar nesecito para tres paredes pero la quiero así como lo escribí en el comentario anterior 🙏
@emcallah4 жыл бұрын
At 1:00 into the video, after toggles are pushed into the wall, the video says to tighten the bolts. So I now have 5 toggles inside my drywall, and the bolts DO NOT tighten into the toggles... am I missing something? For me, the bolt & toggles just spin endlessly, with no way of “grabbing” onto each other. So instead of a time-saving store bought shelf installation, I need to figure out how to fix this. Theres no way I can think of to get the toggles back out :0(
@madisonoiler8973 жыл бұрын
Hey! I had the same problem and I just put mine up, I pulled the track away from the wall to put pressure on the toggles and used my drill to make my life easy and screw the bolts in! I hope this helps
@chalemasters35113 жыл бұрын
I just had the same exact thing happen the toggles are gone and I have 4 huge holes in my wall
@jimsterling9357 Жыл бұрын
@@chalemasters3511 You must know how to use toggles! After poking them through the wall, pull back on them until the "wings" on the other side hit the wall . . . THEN start tightening the screw!
@chrissydavies_temp_user Жыл бұрын
@@jimsterling9357 can you be any more.specific? I don't think the toggles are supposed to go all the way through to the other side of the wall. The 'wings' or 'flaps' are supposed to be inside the confines of the thickness of the drywall. If it goes all the way through there's no way to tighten.
@MymyNguyen27111 жыл бұрын
where i can buy this product ?
@dejavu2675 жыл бұрын
I got mine at Lowes
@maharijawarapulika13494 жыл бұрын
Mymy Ng Home Depot too just got one.
@gabrielgonzales81634 жыл бұрын
el.ranchero muylinda amor💜
@twinvestormorgan43993 жыл бұрын
At 1:33, she placed an extension onto the bottom of the standard; how did she do that? Did I miss something?
@grammargirl61623 жыл бұрын
I noticed the same thing and have the same question. What are those? I've never seen them at the store.
@cspann337 жыл бұрын
Is the hanging rack sturdy enough for heavy clothing?
@ClosetMaidOfficial6 жыл бұрын
Yes, sorry for our delay. If you mount the hang track into studs it can hold heavy clothing.
@kishorurity60966 жыл бұрын
what is it called, that they used @ 0:52 in the video ?
@ClosetMaidOfficial6 жыл бұрын
A toggle bolt. The hardware is available on our website or at your local hardware store.
@aneshabritford29423 жыл бұрын
Thanks so much for showing how to install the super sliders, one of mines came off and I couldn't figure out how to put it back on🤦
@ladybluu7 жыл бұрын
Any ideas on how to organize a closet with a raised ridge in the middle of it? I wont be able to lay a bracket flat against the wall because of it.
@sourcabbagefamily6843 жыл бұрын
We installed the system but now I want to redo the whole thing how do I remove all the studs etc without destorying the wall?
@imagin4eva9 жыл бұрын
Great job but using a stud finder to drill over studs is dangerous as electronic stud finders often beep when over pipes and wires too. Never drill over studs but avoid.
@computergroup2562 жыл бұрын
What do you mean by drill *over*? What do you mean by the "over" part? You mean don't drill *into* studs???
@SpicySapphire7 жыл бұрын
Now I need to patch up all the holes the toggles made.. sigh
@carlinamercedessanchez38313 жыл бұрын
Perdón donde consigo eso lo nesecito así como el de las parrillas o rejillas largas tres así de largas de un metro o 1.50solo las tres res rejillas largas y de 20cmmts de ancho con intervalos de 25cm de alto ____________________ ____________________ ____________________ Nesecito así para colocarlo en mi casa
@carlinamercedessanchez38313 жыл бұрын
Disculpa en Bucaramanga Colombia se consigue me podría decir el local
@ricknelms4 жыл бұрын
Why can't you install it in an opening bigger than 6 feet? You aren't attaching anything to the side walls. If your standard isn't on a stud putting the screw in makes no sense ,that's where you should you the toggle no?
@nehals76732 жыл бұрын
Who is watching this in 2022
@4dareids2 ай бұрын
Watching in 2024
@MoonlightSonata214 Жыл бұрын
I wish they would tell you the weight capacity.
@d8zdly3 жыл бұрын
So, Home Depot didn’t tell me I needed a toggle thingy! Ugh back to HD I go
@mockingbird1873 жыл бұрын
That's their actual slogan: "You'll be back!"
@tanushreemenon48077 жыл бұрын
what kind of shelf is suitable for mounting an oven toaster on the wall?
@lexilooo38207 жыл бұрын
Tanushree Menon I would suggest strong wire shelving, like in the video
@tanushreemenon48077 жыл бұрын
LexiLooo thank you
@mohammadal-zghoul39357 жыл бұрын
I like this
@anilreddy79023 жыл бұрын
How much of price
@fahteeema6 жыл бұрын
Where can I go to buy this stuff?
@ClosetMaidOfficial6 жыл бұрын
You can purchase our ShelfTrack Kits on our site at www.closetmaid.com. We also offer a free easy-to-use design tool where you can custom design your closet. You will also find our ShelfTrack system nationwide at The Home Depot.
@brandonjones96355 жыл бұрын
Since all the weight is on the hang track, I'm surprised ClosetMaid did not specify the size of toggle bolt one should use. Also, the CM video states that at least one track attachment should be into a stud. But is says nothing about what size screw should be used? The printed CM spec sheet also says nothing about the toggle bolt size. However, buried in the tiny type I found the recommendation that the screw be a #12 x 2" pan head.
@sankarisarkar40706 жыл бұрын
Where we are going to get it.
@Amandatassler9 жыл бұрын
how do you cut the hang track if you need to?
@Superj3439 жыл бұрын
table knife+luck+patient Maybe.
@JoyfullJuneBugg9 жыл бұрын
Amanda just use a small hand saw.
@dilciaenid579 жыл бұрын
Did the hang tracks come with the rest of the order or did you purchased separately?
@lilbil2354 жыл бұрын
It actually takes longer to take the stickers off cleanly than to put up the whole system
@randysewell40106 жыл бұрын
@ClosetMaid or to anyone that can help. I am trying to purchase these kind of racks. What do I ask for at the store? What are they called?
@ClosetMaidOfficial6 жыл бұрын
More than likely you will find the product named ShelfTrack at your local Home Depot or other retailers. You can search for the product on our website www.closetmaid.com and choose where to buy. It's Adjustable Hardware under Closet Storage & Accessories on our site. You will need a Hang track, Vertical Standards and Wire shelving and applicable hardware depending on your wall type. Wire Shelving is available in different types. What you are seeing here is the SuperSlide Shelf.
@randysewell40106 жыл бұрын
ClosetMaid Thank you!
@joselynfierro8948 Жыл бұрын
Yeah I can’t do this 😭😭😭
@latengocomoburro2 жыл бұрын
Yo do not need the HangTrack, that is just BS to make you waste more money on a product which is already VERY EXPENSIVE for what it is. Just draw a level and put all top screws on that line. Also, you do not need that many standarts, 4 per closet is fine just make sure you attach all of them to the studs.
@Superj3439 жыл бұрын
1:33 ????????????????????????????????????
@incognito6158 жыл бұрын
They used a standard connector to connect the two bars.
@sejlefrew4 жыл бұрын
Yea, I raised an eyebrow as well...Just using a screw into drywall, that won't hold, needs to be a drywall anchor or screwed into a stud, poor job on their part.
@bunnyholez2 жыл бұрын
Bruh…. How the fuck my toggle anchor is like 10 times bigger than hers?! Now im trying to make half inch hole with 3/8 and its a paaaaaain
@bunnyholez2 жыл бұрын
So took me about 3-4 hrs lol; the holes are almost size of your hand and make your upcoming closet floor look like coke party is about to bust😂 marking the holes in standards is impossible with regular pencils/pens BUT old school liquid eyeliner saved the day. If i ever clean up the dust i will have bangin closet tho LOL.
@michelleware2416 жыл бұрын
how is she extending the standard?
@ClosetMaidOfficial6 жыл бұрын
Hello, we have a hardware Standard Extender. It is sold separately or included in many of our kits. The item number is 281900 (white); you can find it here online - closetmaid.com/webapp/wcs/stores/servlet/en/closetmaid-us/standardextender.
@aidasaair36985 жыл бұрын
How to get this closet
@captaindrywall4 жыл бұрын
next notice your crap just falls though onto the floor and you can't slide hangers on a pole.
@lole39396 жыл бұрын
..
@Bacardibombillo7 жыл бұрын
I want to Marry her
@iheartTH12033 жыл бұрын
my closet it weird, so these videos don't help much lol. i have a small, square closet. 3'9.5" X 3'10" X 8'0" (L x W x H)
@sarvarzjjatt92406 жыл бұрын
really good but where i can buy this material
@ClosetMaidOfficial6 жыл бұрын
Thank you; ShelfTrack® is available nationwide at The Home Depot or on homedepot.com or on closetmaid.com.
@jeffreyanderson8006Ай бұрын
I can’t hear it
@Kimberly-vz7tq23 күн бұрын
The worst…you’ll end up hating the wire and wish for real shelving
@oshylu9 жыл бұрын
it is nice ...
@MTVlogs11 жыл бұрын
Home Depot
@elleanlim54683 жыл бұрын
Y
@mamasakunee5 жыл бұрын
This product sucks. It is not as easy to install as video says. End up making huge holes on my wall trying again and again
@samithmadushan4504 жыл бұрын
I want to marry u☺☺☺
@ameralsayed-dl3vk Жыл бұрын
This shit is freaking expensive
@shellybee93222 жыл бұрын
ClosetMaid, My last purchase will be my last purchase from this company. I’m here because instructions weren’t even included. At the very least 1 nut could have been included to make a hole big enough for the clamps. I’m so disappointed.
@cidley31962 жыл бұрын
I hate videos like this! Explaining how to install an entire closet system from scratch in three minutes! There's not enough detail on any part of the instructions. I'll be looking for another video or two by an actual person who knows the challenges an actual person might face and explains everything in detail.
@goingnuclear7265 Жыл бұрын
This video is terrible doesnt even tell you what screws they use. I had to make 2 trips. Should be sold all together