CLUTCH BASKET REBUILD / REPLACING THE CLUTCH HUB ON HARLEY 6 SPEED

Рет қаралды 12,922

11 ай бұрын

While we were working on my buddy Larry’s bike it became obvious that the clutch hub needed to be replaced. The splines on the inside of the clutch hub were breaking down and the metal was getting into the bearing and causing destruction. This is a problem with 6 speeds from 2006 to 2010 and there is no real fix. Checking you hub at regular intervals is the only way to prevent future transmission problems as well.
“Subscribe”, Like and Ring the bell to get notifications of the newest video’s when they come out. Thanks for checking us out! Share us out there. Thanks
/ @itsmytimeletsgo

Пікірлер: 30

@davefowler450 2 ай бұрын

Ralph is a good buddy of mine and is no stranger to Harley motorcycles. Very in depth video with good detail Ralph. Good job.

@itsmytimeletsgo 2 ай бұрын

Gald you enjoyed it Dave. Thanks for the kind words and comment.

@fluffypuppy720 6 ай бұрын

Awesome! the best video on this on KZfaq thank you!

@itsmytimeletsgo 6 ай бұрын

Thanks so much for the kind words. Glad you enjoyed it. Thanks for the comment!

@davemagee 5 ай бұрын

Thanks brother awesome video very clear and easy to follow just about to do the same job on my RG. Subscribed now all the best from NZ🇳🇿🇳🇿

@itsmytimeletsgo 5 ай бұрын

Glad you enjoyed it. Thanks for commenting and letting me know where you are from. Always blows my mind that I am reaching out so far. Very satisfiying and more than gald to help others out there if I can.

@MarkAlves1982 2 ай бұрын

Very informational video! Please make a video on the new Harley Assisted Slip Clutch Assembly.

@itsmytimeletsgo 2 ай бұрын

Thanks glad you liked it. I do not know anything about the Assisted Slip Clutch and do not plan to learn about it. Actually I have never heard of it. Vintage bikes are where my skill set is, and my interest. Sorry I cannot help you out. Hopefully you can find another channel that will specialize in that.Thanks for commenting.

@punitgurumayum 3 ай бұрын

Very helpfull

@itsmytimeletsgo 3 ай бұрын

Glad you found it helpful. That is why I do You Tube. To hopefully help other on their way. Thanks for commenting.

@MrNetnut 2 ай бұрын

Nice Job Sir./;-))))

@itsmytimeletsgo 2 ай бұрын

Thank you and glad you enjoyed it. Thanks for commenting.

@user-eq4qd8sx5l Ай бұрын

I hear the aluminum baskets are prone to cracking. Perhaps a good time to replace it with a heavy-duty basket? My clutch chatters going into 3rd when it's cold about one or two times but never after it's warm.

@itsmytimeletsgo Ай бұрын

Ya work with what ya got. gald you enjoyed it. Thanks for the comment.

@jeffweaver7011 4 ай бұрын

@itsmytimeletsgo Great video. I subscribed. I have questions. Trying to solve a noisy primary. Replacing the inner primary bearing. Started looking at the clutch. Didn't know that I would need a press.Until i watched your video. When i removed the two snap rings, I pushed the hub out with my hand !! So, i need a hub as well as a bearing? Or should i see if a bearing will tighten the fit? Thanks

@itsmytimeletsgo 4 ай бұрын

Thanks for subscribing. I would guess that the hub is worn if the bearing fell right off of it. You can measure your hub to check the diameter against a new bearing, hub should be bigger than the inside of the bearing by a thousands or 2, but I would suspect that very likely the hub is shot. Thanks for the question. Hope it helps you out.

@Mrwill927 4 ай бұрын

What if you do not have a press? Great video by the way!😊

@itsmytimeletsgo 4 ай бұрын

Good Question. I do not think there is really any other way to do it properly. Maybe somone out there has a solution and will comment. Sometime you just have to bite the bullet and find somone with a press. Thanks for the question and taking the time to comment!

@barrybutt7647 2 ай бұрын

Watched this before I switched my plates. Thanks😎

@itsmytimeletsgo 2 ай бұрын

Hope it helped you out. Thanks for the comment.

@randybard224 3 ай бұрын

where did you get those snap ring pliers in your clutch hub repair video thanks

@itsmytimeletsgo 3 ай бұрын

Princess Auto. Thanks for the question, and thanks for commenting.

@hoopin4you 2 ай бұрын

I do not currently have a shop press. Does it need to be 12-ton to do this job?

@itsmytimeletsgo 2 ай бұрын

No mine is only a common small jack type 4 ton. Thanks for the question and comment.

@markwhite8543 4 ай бұрын

My splines look just like that. Unfortunately, my ring gear is chewed up a bit, too, so I'm looking at buying the whole assembly. What causes this damage?

@itsmytimeletsgo 4 ай бұрын

It is an on going problem with the 6 speeds of those years. Transmission problems can also contribute to the problem. Bad bearings in the right and left sides allowing the mainshaft to shift, when going form 5th to 6th and back down to 5th. Usually you will get mainseal leaks when the bearings are bad as well. Good luck. Thanks for asking and commenting.

@balmand4043 4 ай бұрын

I just pressed in a new hub. Installed the snap ring. Spun it and its noisy. Should be silent?

@itsmytimeletsgo 4 ай бұрын

They are big bearings so they do make some noise when you spin them. But they should not sound like the are scrapping, or rough turning, so to speak. You have to make sure to support the bearing properly, in the center, when installing the hub so as to not put pressure on the bearing itself. Thanks for the question and commenting.

@balmand4043 4 ай бұрын

@@itsmytimeletsgo thx for your reply! Ok, I checked with indy shop, he said its normal since its dry. It doesn't feel rough or like its scraping anything. Can't wait get it put back together!

@itsmytimeletsgo 4 ай бұрын

I figured it was ok. Good luck with assembly.@@balmand4043