Co2 Laser Auto Focus Offset Adjustment for Correct Focus Height
Рет қаралды 24,761
2 жыл бұрынThe purpose of this video is to show you how to make the necessary adjustments to your auto focus to correctly set the focus height. This might be needed after completing a ramp test or after making any adjustments to the auto focus pin.
To see the difference between auto focus and manual focus take a look at this video:
• Focusing your Co2 lase...
Affiliate links:
OMTech Lasers:
omtechlaser.com/LSG
Affiliate code “LASERGUYS”
Coupon code “LASERGUYS5OFF”
Auto focus replacement - amzn.to/3HWDAdi
Calipers - amzn.to/3D67Kat
Affiliate Store - amazon.com/shop/beardedbuildsco
Socials:
beardedbuildsco
Facebook.com/beardedbuildsco
Beardedbuildsco.com
OMTech Facebook Group:
/ 1364016877267714
@michaeldorety624 2 жыл бұрын
Yesss … been waiting on this video for a couple months now.. thank you
@BeardedBuildsCo 2 жыл бұрын
You’re welcome!
@michaeldorety624 2 жыл бұрын
@@BeardedBuildsCo what about the material on the bed… why didn’t you account for that??
@BeardedBuildsCo 2 жыл бұрын
Because that is the material you would be zeroing off of.
@fredwienbarg5051 2 жыл бұрын
Very helpful. Thanks!
@fendefilms 2 жыл бұрын
Awesome video, great info, thank you!!!
@BeardedBuildsCo 2 жыл бұрын
You’re welcome!
@torbenKristensen-ql7ep 4 күн бұрын
TU. Just what i wanted😄🇩🇰
@DS-ng2kj 2 жыл бұрын
Thank you!!
@rb95403 Жыл бұрын
super helpful
@BeardedBuildsCo Жыл бұрын
Thanks!
@whynotcnc8828 2 жыл бұрын
well done
@dishatechno7793 4 ай бұрын
Small foult but it is most important focus is set then cutting smooth and time save OK sir thank you
@rustyp21 Жыл бұрын
Great video! I just got a Monport 80w laser and have it all connected with water chiller, exhaust venting, etc. I have a bit of experience with an Ortur LM2 Pro diode laser but no experience with a CO2. As I see it, the first thing I need to do is a ramp test, then change my offset in LightBurn, and do a test card. Do you have any suggestions on the next steps I should do, or any videos I should watch? I see a lot of people adding cameras, LED lighting, and air assist upgrading - are those things you personally recommend? Thanks for all you do! PS - I’m from Ogden but just moved to Mesquite about a year and a half ago. I see you are very close to where I used to live.
@afbigfish1 2 жыл бұрын
do or should you do a ramp test for different thickness materials? I dont have a laser yet but I think I saw some videos saying you can get better results cutting thicker material slightly out of focus. so I assume you should do a ramp test for the different thickness... Also can you assign different z heights for the layers in LB so the laser can engrave slightly out of focus and automatically adjust to in focus for cutting operations? Im planning on buying the same omtech 2440 100w laser.
@margyg 2 жыл бұрын
Did you try it by setting the offset with the pin depressed? I understand you want the specific offset from the bottom of the dropped pin for the magnets, but curious if the distance you actually set was with the pin depressed as it does when setting autofocus. I literally just got my machine, so I haven't tried that yet myself.
@bullitttechteacher 2 жыл бұрын
Why the 9mm adjustment? Where can I get the template to create the mm step guide? I have a OMT 60w in my middle school classroom but it seems to be out of adjustment. It will not even cut through cardboard
@JustiaFiat 8 ай бұрын
Can you lower the laser head in between passes when cutting something very thick? I know that's possible for some diodes but have not found information regarding co2
@zachofalltrades6116 2 жыл бұрын
I finally figured this out watching your video but my problem is my auto focus pen drags on material moving it how can I adjust it where it’s barely off the material. I have mine set at 14.8 for my distant of my laser focus so maybe I’m not doing my offset part right
@BeardedBuildsCo 2 жыл бұрын
If you need more space then you need to adjust the pen up and then increase the offset.
@yankomaceda34 Жыл бұрын
How to automatic change focus between layers for kisscut?
@rickmccaskill7888 2 жыл бұрын
Thanks for sharing. I have been fulling your video but I have an issue. When my 50.8MM lens focuses at 3mm vs yours at 18mm. If I adjust mine the sensor is below the lens so it hit everything. Should I place a offset piece under the sensor and raise the sensor to that offset piece whenever auto focusing my laser? This way the sensor trips at the right autofocus setting.
@BeardedBuildsCo 2 жыл бұрын
Co2 Laser Auto Focus Offset Adjustment for Correct Focus Height kzfaq.info/get/bejne/l950rNVyt77Imqs.html
@GilbertFlores956 7 ай бұрын
What if my new OMTECH doesn't have an AF pin attached? I think they did away with it recently so how do I adjust focus height without that pin tip that's shown on this video?
@BeardedBuildsCo 7 ай бұрын
Same principle just using the end of the nozzle as the “pin”
@par195 2 жыл бұрын
What is your Facebook page? Great video.
@tslayer87 2 жыл бұрын
Just curious on how smooth the delivery for your machines was? I’m in Lehi and have some concerns with it showing up un-damaged. Is there a specific company you buy from?
@BeardedBuildsCo 2 жыл бұрын
I ordered mine through OMtech. omtechlaser.com/?ref=lgs The are based in California and provide US customer service.
@RCjunkie 8 ай бұрын
I can not find my z movement on the controller
@tyler4462 Жыл бұрын
Your videos have been incredibly helpful. I think I have the same or very similar machine. My ideal focus is about 17.5mm. I put my autofocus pen where I wanted it and then adjusted the number in the Z home offset area. After I write the number, the machine does nothing different. I can put 10mm offset, or 50mm. The machine still auto focuses on the exact same spot. Any ideas?
@BeardedBuildsCo Жыл бұрын
Depending on your controller you might have to adjust the U axis rather than the Z axis
@tyler4462 Жыл бұрын
@@BeardedBuildsCo I ended up changing the settings on the laser itself instead of in light burn. Now it works great. Thank you!
@timuphoff4205 2 жыл бұрын
When I go to machine settings there’s no x. y. or z axis settings . Just curious if there is another screen or something not set correctly. The laser says ready .
@bullitttechteacher 2 жыл бұрын
It's the last one under Vendor Settings. Pops up a warning click yes then you will see Z axis
@Sandyloucustomdesigns 6 ай бұрын
ok so in the machine settings I do not have option for any of the axis settings especially the z axis. is something I am missing? I setting up my omtech 100 watt auto focus laser
@BeardedBuildsCo 6 ай бұрын
It is a subsection of the vendor settings
@Sandyloucustomdesigns 6 ай бұрын
I’m sorry what does that even mean? What vendor? It is from Omtech?
@BeardedBuildsCo 6 ай бұрын
@Sandyloucustomdesigns in the machine settings under the vendor settings area you will find all of the axis
Nifty Woodworks
Рет қаралды 6 М.