Thank you. Absolutely the place to seek parts from to support the channel.

THANK. YOU. Im doing my first ever carb overhaul on a 72 scrambler and you saved my ass, boss.

Loved the "expert" tip about shaking the float and listen for fuel, just in case the solder joint is leaking. Excellent!

That diaphragm is in excellent condition. I've taken 10 apart and every one of them had 3 little tears over the air bleed brass inserts. A damaged diaphragm leads to "digital" throttle control where power snaps on and off. I am really amazed at the replacement parts you can get today that were not available to us in 1976, like diaphragms, floats (had to re-solder several of them), gasket kits, etc.

Brendan you are the best. Clear concise videos with not a lot of extra talking or had gestures. Tells me just what I need to know and what to expect.

Best how-to video's on youtube, massive thanks for taking the time to show us all how it's done. Respect.

this guy is a lifesaver

This video helped me find out why my 70 CL350 was so unresponsive. Fluid in the bowls. Keep it up Common Motor!

Fantastic video!!! I love your step by step explanations. Just great and gets it done!

You guys have helped me out so much, my 73 cl350 and 74 cb360 appreciate it!

I never get tired of the one!

This is excellent information. Just got a 73 350 twin and need to re-jet the carbs after the exhaust modification. You've got a new member for your website!

Enjoy the slow careful explanations and stopping to make sure the camera view is perfect. Thanks!

Really excellent series of videos on the CB350 carbs. Very, very helpful. I'm sure I would have "unscrewed" and broken one of the emulsion tubes if not for you. (In fact, one that was in there was broken!) Thanks for the whole series!

Removing carburetor assembly (CB250, CB360,CL360,CJ250T,CJ360T): Remove left front foot peg. Remove gearshift pedal retaining screw. Remove gearshift pedal. Remove left rear crankcase cover (the cover where the clutch cable goes in--don't remove the clutch cable from the cover. The cover is held by four Phillips-head screws). Remove the hose clamps that hold the air-cleaner rubber intake ducts onto the choke sides of the carbs. Remove the air cleaners, still connected to their rubber ducts. Loosen the insulator ring clamps (The insulators are the rubber boots/ducts between cylinder heads and the carb intakes). Detach spark plug wires from plugs and put the wires out of the way. Be careful not to harm the ignition wire that goes into the points housing. Pry the carb assembly away from the head, toward where the air boxes were. Lower the carb assembly to the left and pull it out the left side. Detach the throttle cables from the carbs.

Very very helpful... Keep up the excellent job of informing us.. Thanks a lot.. stay safe..

thank you, rebuilding dual carbs on my green cb350 bike thats been sitting for 20 years.

Thank you for this video!

simply excellent

Your touching on many points that a good many people completely bypass or overlook entirely. The air bleeds and emulsion tubes seem to be oversights with quite a few folks I know. That plug for the transfer adjacent to air-fuel mixture screw the other. The last one bordering on the nightmare since many believe the carb is no good any longer as it can't be tuned without that plug.

Very detailed video, thanks! Can you tell me if this is the same carby for the CB250 1971? It looks identical. Ive removed the float bowl and everything looks the same as in your video.

great video, calm instruction on how to rebuild a cb350 carb. added bonus at 10:35 the magic finger moves the plug into frame.perfect. made me laugh.

Do you guys have choke butterflies replacement for the cb350 carbs or know where I can get some

Great vid. You should edit it down just a bit, mostly when you’re screwing/unscreeing. Otherwise, Thankyou for the detailed information! I’m a noob with a 1974 CB 360

I shaved down the chopstick with the Xacto for the smaller emulsifier tube removal.

Do you have a video on how to install the carbs in the bike?

Can't find jet retaining clip on site. Need one over here.

The shaft my butterfly rotates on is so stiff it feels solid. Any ideas on how to get it to move?

That black rubber plug. Is it on the early carbs?

Good morning. I have a 70 SL350 with these carbs. I have them disassembled and I have your kits and diaphrams . I put them in an ultrasound cleaner and a lot of microscopic stuff came out. They look really clean to me. I don't really want to knock out all jets . Do you think it would be ok or not really.

Is this a similar process for the carbs on a cb350F?

Hi, did you have a video of how to get a pair of carburetors out of a 2-cylinder Honda motorcycle? Thanks

nice!

great

Can’t wait till I get 450 Honda running

My CB 350 runs great when warm but cold start choke don’t do anything and when I start it I can’t touch throttle or it stalls

Both my carb plungers/pistons are stuck in their bores. How do I get them loose?

My fuel inlet nipple came off the carb. How do I repair that??

does this hold true for a 73 CB350G?

I'm having issues with my K4. Someone suggested that I might have an air leak from the white plugs in my carbs. Have you come across this? My white plugs are both there, and don't seem loose. Thanks

My float bowls each a pin sized hole in the bottom by the brass insert, I'm guessing this isn't normal?

What did you soak them in since you didnt remove the shafts?

I cleaned my carbs, put them back on the engine and found the engine hard to start. When it started after about 6 kicks, the engine rev-ed to about 5k. The inlet butterflies were closed when this happens and when I press down hard on the throttle stop arms I can bring the revs down to tick over. Can you suggest what might be the cause? Does the butterfly have pivot seals that might be causing an air leak. When overhauling I noticed there wasn't a washer or seal in the air mixture screw, yet this wasn't a problem before cleaning.

I wondered why it was called Common motor- turns out it’s the street name where they are located

Pick tools ordered and Chinese food takeout ordered 👍

are these the same carbs on a 68-69 cb350?

You only deal with the twins?

There's liquid in my float. Would that make the whole bike not start? Because the engine turns but won't start up.

Someone watching this is like, shit, how do I get the carbs off the bike? lol

I have a manual, just looking for quality parts at a fair price.

But not the 350f

Interested but finding those weird gloves a bit off putting thanks anyway