Conduit Bending: Parallel Offsets, How to calculate and implement Parallel Adjustment Constants.

Рет қаралды 62,424

4 жыл бұрын

In this video I show you how to find the parallel adjustment constants and how to implement them in your offsets to create equal spacing throughout all of your conduits. I also give you a quick offset bending example, even though the video is not about how to bend an offset. I threw it in anyway.
Reminder:
Just want to take the time out to stress that when you take your measurement to calculate parallel adjustment, you MUST TAKE THE MEASUREMENT FROM CENTER TO CENTER OF THE CONDUITS YOU ARE BENDING THE OFFSETS FOR. It will not work otherwise. Also it doesn't matter if you are doing horizontal parallel offsets or vertical offsets, so long as you get the center to center measurements from the conduits it will come out just fine.
I posted all the Parallel Adjustment Constants in the video, you should either write them down or take a screen shot and keep them on you. After watching this video there should be no reason why you don't make your offsets with more than one offset a Parallel Offset.
Also please consider supporting the channel
Holmz Law Amazon wish list
www.amazon.com/hz/wishlist/dl...
paypal.me/melrub480v?locale.x...
If you have any questions or would like to stay updated follow me on
Discord - (Host live Q&A sessions) request your private link
Facebook - HolmzLaw
Reddit/HolmzLaw
Snapchat/Holmzlaw
Instagram - HolmzLaw
Twitter- Livewire480v@Holmzlaw
TikTok- HolmzLaw
#EMT#conduitology#paralleloffset

Пікірлер: 202

@dtv1966 3 жыл бұрын

Let me tell you something brother I am a journeyman. I topped out of the IBEW apprenticeship not to long ago and in my first two years in the program my instructor couldn't do a better job than you in explaining this concept of conduit bending. In fact, he didn't even bother teaching this concept. I barely did any conduit bending in class so needless to say I had a hard time bending pipe in the field. But I want to thank you for this video brother. And if there's any apprentice watching this video pay close attention;this man is the truth. Keep up the good job brother.

@TheArtOfConduitBending 3 жыл бұрын

Let me start out by saying Thank you very much. I'm really trying hard to explain conduit bending in a way that any apprentice can pick up a bender and complete a decent bend. I know starting out I didn't have this I had to look and find and try to dig up literature and it wasn't very easy at all. Basically only had the benfield manual. So I decided to just refresh my self with trigonometry and through the years I was able to just figure stuff out through trial and error and not to mention always asked the more experience journeyman what ever questions i had. Anyhow Thanks again. If you have any questions at all feel free to contact me anytime on any of the social medias @Holmzlaw.

@Bludcharg4214 3 жыл бұрын

Good to know- second year apprentice

@hooddonations173 2 жыл бұрын

Thanks I’m a appreciate . I need some game from the big dogs 🤛

@davidargil8694 Жыл бұрын

Second year ibew apprentice here and I can relate to what t dyer commented thank you so much brotha I really appreciate your videos. You put me on game with all your videos much appreciated

@tucanblanco5393 Жыл бұрын

Just wanted to let you know that I am doing a lot of research on Bending Emt, today i been more than 9 hours on it

@jokn7315 3 жыл бұрын

Badass. I've always have trouble with parallel runs with different size conduits. Love the depth and the details you go through that explains everything. Keep up the good work.

@TheArtOfConduitBending 3 жыл бұрын

I'm glad I was able to help you. I'm not sure if you know but I just put out a 3 part series of video's about Parallel Kicks. I've completed and posted 2 of them and the 3rd is on it's way. Thanks again for watching. Please share and subscribe!

@kahlil4745 3 жыл бұрын

Dude you are saving my apprenticeship! You are by far the best teacher I have had.

@TheArtOfConduitBending 3 жыл бұрын

Thank you for watching my Dude. Follow me on or send video request: facebook@Holmzlaw instagram@Holmzlaw Tiktok@Holmzlaw

@josecontreras6827 5 ай бұрын

Keep up the good work brother it’s nice to see a fellow electrician that is willing to share his knowledge and help others in our trade. Whether you’re new or have been doing this for a while Melvin is by far the best instructor I’ve seen and heard. You never stop learning I know I’ve learned a lot just from watching your videos. Respect.

@TheArtOfConduitBending 5 ай бұрын

I really appreciate the comment. Thanks.

@josepina4622 3 жыл бұрын

You are fine, I understood it perfectly, I just wanted to ensure that the result (difference between the first offset) was added to the second offset ... thank you for sharing your knowledge

@AnthonySparks-wb3gg 2 күн бұрын

From a fellow IBEW Brother salute !!

@frederickvanpelt6393 3 жыл бұрын

Thanks for taking the time to make this tutorial. I'm retired now but still interested in the job, glad to see you take pride in your work, there is too much fast track work going on where quantity trumps quality. I was taught as an apprentice that " long after the cost of the job is forgotten, the quality shall remain".

@TheArtOfConduitBending 3 жыл бұрын

Thanks for watching!

@tim44120 3 жыл бұрын

Im so happy I found you. I really appreciate what you are doing. This knowledge that should be abundant is not. You are rare out here. Please keep doing what you are doing. My hat’s off to you. Thank you

@TheArtOfConduitBending 3 жыл бұрын

Thank you first of all for the comment and for watching my video. I will be coming out with more videos. I try to do at least 2 a month because of my schedule. Im also doing podcasts which are a lot quicker if you are interested. Again thanks and please support the channel by sharing it with your friends and co-workers. Anchor.fm/holmz-law & All major podcasts Follow me on: For daily content Facebook@holmzlaw IG@Holmzlaw Tiktok@Holmzlaw Twitter-Holmzlaw@Livewire480v

@ivanrodriguez1423 2 жыл бұрын

Thank you for all your help brother I loved your videos I've been out of electrical for 10 years just came back and now I'm running circles around all these apprentices!!

@TheArtOfConduitBending 2 жыл бұрын

Thanks for watching and most of all for the comment

@jacklacayo8079 3 жыл бұрын

Professors I admire you a lot when you are going to make parallel curves. Your classes are very helpful. Thank you. I am offsets in parallel. I learned a lot !!

@TheArtOfConduitBending 3 жыл бұрын

Thank you. Please help me spread the word to othere electricians that want to learn how to bend pipe. Thanks again. Please subscribe.

@jeremyragsdale8530 4 жыл бұрын

Thank you bruh! I appreciate you taking the time to make the video. This helped me out big time! Best conduit tutorial page on KZfaq

@TheArtOfConduitBending 3 жыл бұрын

Thanks for watching. If you have any video requests please send them to facebook@Holmzlaw instagram@Holmzlaw Tiktok@Holmzlaw

@williecotton-fy2sr Ай бұрын

The way you broke it down was A1. Thanks for the insight .

@TheArtOfConduitBending Ай бұрын

thanks brother

@IVAN2233 3 жыл бұрын

Great video. I’m just starting my apprenticeship and I’m going to check out all you videos to learn how to bend conduit. 👍

@TheArtOfConduitBending 3 жыл бұрын

New video posted for apprentices in case you dont know how to build conduit supports out of unistrut. Check it out.

@user-rz9co1cu9s 6 ай бұрын

2023 and I know the fundamentals of bending but even know after this video I understand things that for sure I know I’ve been struggling with, I’m a Solar electrician so I touch a lot of conduit as well. Great video thanks 💪🏼

@titussardonicus338 Жыл бұрын

I did my entire apprenticeship in residential, non-union. Here I am now, in the union, working commercial, and I'm that resi guy that everybody makes fun of. These videos are lifesavers. Thank you brother.

@TheArtOfConduitBending Жыл бұрын

No problem. Let me know if there's anything I can help you with.

@stevebuchanan5773 4 жыл бұрын

Nice job, im a residential custom home condo guy. Pipe is something i get my hands on few and far between, but im moving and i know the work there is more commerical industrial. I am currently practicing my skills at home after work with youtube vids with a bunch of 1/2, 3/4, and 1" and my uglys book and a ibew conduit card a old timer gave me when i was an a apprentice. Keep the vids coming

@TheArtOfConduitBending 4 жыл бұрын

That's great. If you have any questions feel free to ask me any time. For up dates and just to see my daily posts of what im working on for the day. Follow me on: m.facebook.com/story.php?story_fbid=2326578694317968&id=1427456774230169

@fierrofierro5721 3 жыл бұрын

Bro! I learned thisnin high school, but i had totally forgotten about it, about how to do that calculation. You explained it just right bro thanks a lot!!!!!!!

@TheArtOfConduitBending 3 жыл бұрын

Im glad you enjoyed it brother. Happy Thanksgiving. Im working on putting together an electrical calculation playlist too. Already have a few videos in the list. Also im on podcast now too. All major ones. You can see which ones on anchor.fm/holmz-law Also i have an advanced conduit video course playlist completely free. I have to warn you to warn you the video's are long and the style of bending is probably something you're not use to. Go check it out on the channel.

@beeitti1 3 жыл бұрын

Great video! Excellent tip at the end. That was really helpful. Keep up the good work. Stay safe

@TheArtOfConduitBending 3 жыл бұрын

Thank you. And thanks for watching. Follow me on Facebook@holmzlaw Instagram@Holmzlaw Tiktok@Holmzlaw Post work here #conduitology #conduitologist #conduitologism #holmzlaw #artofconduitbending

@nonjon6583 3 жыл бұрын

easy way to calculate shrink (aside from memorizing) Is the given angle divided by 120 Ex: 15 degrees is 15/120 = 0.125 = 1/8 22.5 degrees is 22.5/120 = 0.1875 = 3/16 30 degrees is 30/120 = 0.25 = 1/4 45 degrees is 45/120 = 0.375 = 3/8 and so on

@TheArtOfConduitBending 3 жыл бұрын

Thanks for the info. Also thanks for watching.

@geart1971 3 жыл бұрын

great tip , thank you

@johnnyem-grafix4024 Жыл бұрын

Good morning Mel ! You’re making me shine at work. Thank you for taking your time and passion and helping us 🤝💯👍🏻

@TheArtOfConduitBending Жыл бұрын

Wow thats great! Post some pics on the discord community if you can. Have a great day. If you're not a part Úof the community. Here's the link. discord.gg/UDKsyVBQ

@johnnyem-grafix4024 Жыл бұрын

@@TheArtOfConduitBending okay cool, yeah will definitely check it out on way home

@tucanblanco5393 Жыл бұрын

U are the best on KZfaq explaining this techniques,

@TheArtOfConduitBending Жыл бұрын

Thanks really appreciate it

@ryanb1874 3 жыл бұрын

Love that calculator, got everyone to go set one at the place I used to work when the buttons on their older casinos started falling off.

@TheArtOfConduitBending 3 жыл бұрын

Yeah I loved that calculator too. It broke at work. I need to get another one just like that. They don't last very long at work. I need a robust scientific calculator built for the construction environment.

@myboysanji 2 жыл бұрын

Well explained as a pre-apprentice this helped a lot! We did a parallel offset today but my journey did a pretty shitty job. He didnt use tangents, shrinks and angles. I think he just wanted to finish the job. Didnt really learn anything from him.

@TheArtOfConduitBending 2 жыл бұрын

If you don't do the calculation it just takes so much longer and you have the chance of it coming out wrong. The calculation really isn't that hard either. Really quite simple.

@troynear9877 3 жыл бұрын

Thanks. Well Done! Keep teaching

@TheArtOfConduitBending 3 жыл бұрын

Thank you im trying to do my best. I love passing it on. Follow me on Facebook@holmzlaw Instagram@Holmzlaw Tiktok@Holmzlaw Post work here #conduitology #conduitologist #conduitologism #holmzlaw #artofconduitbending Also got a group on FB "Art of Conduit Bending"

@pigracat 3 жыл бұрын

You are the best bro You teach better than the teachers

@TheArtOfConduitBending 3 жыл бұрын

Thank you very much. I really appreciate it from the bottom of my heart. There will be a new video posting today at 8pm. Please consider donating to Paypal.me/melrub480v Follow me on Facebook@holmzlaw Instagram@Holmzlaw Tiktok@Holmzlaw Post work on these hashtags #conduitologist #artofconduitbending #holmzlaw #conduitology #conduitologism

@codyhelms2732 9 ай бұрын

Great videos very helpful and educational. Thank you.

@TheArtOfConduitBending 9 ай бұрын

Thank you

@tucanblanco5393 Жыл бұрын

I wish u good health all the time so u can be making more vids like this

@kennethbogle4359 2 ай бұрын

Greatly appreciate your videos M.

@TheArtOfConduitBending 2 ай бұрын

Thank you Kenneth. I would appreciate a review on my linked in services if you have linkedin. Have a great day.

@EdgarM-bt1md 3 ай бұрын

Danm this helps out a lot and it makes a lot of sense now thank you very helpful

@TheArtOfConduitBending 3 ай бұрын

You are very welcome.

@8620minis 2 жыл бұрын

You’re The Best Brother…..thx once again

@TheArtOfConduitBending 2 жыл бұрын

Thank you. Anytime brother.

@miguelcortes8388 3 жыл бұрын

Great job!

@Tito-nw6te 3 жыл бұрын

Nice job great video

@elroyelogan2969 Жыл бұрын

You are simple the best

@cherylesquivel7303 3 жыл бұрын

Hi Bro Mel thanks again for all this great pipbending experience. I dont have conduit right using hose filled with ice. Lots of snow out right now. Your really helped me stay positive while bending only after all calculation layout. I know you want us to be the best Mel it shows in your video's. Me and Fam Thank you Homerun all the way😊

@TheArtOfConduitBending 3 жыл бұрын

Yes I want you guys to be the best you can possibly be. Conduit benders make money and no one can ever take the knowledge away

@urielalva2949 3 ай бұрын

Appreciate the video bro thank you 🙏🏽

@TheArtOfConduitBending 3 ай бұрын

Welcome. Thanks for watching. More videos will be coming out this year. Hopefully by the summer. Please support the channel @ cashapp: $artofconduitbending

@letsgobryden5063 8 ай бұрын

Tremendo Capo! Haciendo videos a diestra y siniestra exponiendo y enseñando lo que no se ve en el arte del doblado de pipa. 🤘🏻🤘🏻🤘🏻🤘🏻 Saludos de un mexicano en San Diego Califas!

@TheArtOfConduitBending 8 ай бұрын

Thank you my brother.

@mcm3566 Жыл бұрын

You opened my eyes

@TheArtOfConduitBending Жыл бұрын

I'm glad I did. Please spread the word to your friends and coworkers. Thanks. I'm on all social media platforms and my podcast is Holmz Law Radio.

@jeffstout2318 10 ай бұрын

Bruh your teaching is on point

@TheArtOfConduitBending 10 ай бұрын

Wow I really appreciate that.

@ABAMSYTEL Жыл бұрын

Great video! Tks

@TheArtOfConduitBending Жыл бұрын

Thanks

@danielvargas3292 2 жыл бұрын

Foreal, best Parelle bend video on youtube, only things is i’m probably ganna say “CentA to centA” all day long brother. #332

@Tito-nw6te 4 жыл бұрын

keep up the good work

@TheArtOfConduitBending 4 жыл бұрын

I Really appreciate it. Let me know if you ever have any questions or video requests.

@Tito-nw6te 4 жыл бұрын

@@TheArtOfConduitBending rite on brotha keep up the good content Im watching

@Tito-nw6te 3 жыл бұрын

Hey holmz great vid but which was the one you said you would explain the marks you made on your bender i cant find it

@TheArtOfConduitBending 3 жыл бұрын

Can you give me the time stamp on the video when i said that. Then ill know what your talking about so i could give you the link. Thank you.

@FATBEATSALLDAY 2 жыл бұрын

thank you for this video

@TheArtOfConduitBending 2 жыл бұрын

Thank you for watching Spread the word. I'm here to help. Please follow me on: Facebook/holmzlaw Instagram/holmzlaw TikTok/holmzlaw Reddit/holmzlaw LinkedIn/melvinrubio Snapchat/holmzlaw Tradehounds/holmzlaw Discord- discord.gg/cKgE88wW Communities: Reddit/r/conduitology Facebook/artofconduitbending LinkedIn/artofconduitbending

@SneakerHead-oc9zz Жыл бұрын

Brother you rock

@TheArtOfConduitBending Жыл бұрын

Wow thanks. If you have a LinkedIn account please follow. Also if you want to join my discord community. Both links will be below discord.gg/DpXuJDtd4V www.linkedin.com/in/melvin-rubio

@michaelphillips-nxs 2 жыл бұрын

GOOD JOB !

@TheArtOfConduitBending 2 жыл бұрын

Thanks

@Roboli-nr1mv 2 жыл бұрын

Your the man

@TheArtOfConduitBending 2 жыл бұрын

Thanks my brother. Also thanks for watching. Please follow me on: Facebook/holmzlaw Instagram/holmzlaw TikTok/holmzlaw Reddit/holmzlaw LinkedIn/melvinrubio Snapchat/holmzlaw Tradehounds/holmzlaw Discord- discord.gg/cKgE88wW Communities: Reddit/r/conduitology Facebook/artofconduitbending LinkedIn/artofconduitbending

@HeyYoCee 3 жыл бұрын

Didn't you need to use the 15 degrees tangent 1/8? Looks like you used the . 25 which is for 30 degrees.

@papacitoloko1117 3 жыл бұрын

It's tan(30/2 if you input into the calculator.

@mcm3566 Жыл бұрын

What is a good round spacing in between 3/4 pipe on a rack

@TheArtOfConduitBending Жыл бұрын

usually 1-3/4" center to center or 2" center to center.

@fabiancisneros3512 6 ай бұрын

What about Different size Of Conduict should they be bend at Different or same shoe ?

@fabiancisneros3512 6 ай бұрын

Can I Bend 3/4" 1" 2" at the same Bending shoe Or They Have To Be Bend at Their Own Size shoe? And Thank You You Had help me A Lot With Your Videos

@TheArtOfConduitBending 6 ай бұрын

1"&¾ in a 2" shoe you might not be able to. But I m not positive. I've never tried it.

@briancurran1140 3 жыл бұрын

Very good

@TheArtOfConduitBending 3 жыл бұрын

Thank you.

@smokster0604 2 жыл бұрын

Looks great awesome teacher...Don't let the super see no protection on the floor...

@TheArtOfConduitBending 2 жыл бұрын

Lol... Thanks for watching brother. Most of all for the comment. Love to read these when i get the chance.

@elvizhernandez4305 2 ай бұрын

What if youre taking shrink into account while doing this, do u add shrinkage to your first mark?

@TheArtOfConduitBending 2 ай бұрын

yes so add your shrink first then do your parallel adjustment. Some people get confused but its very simple and the end result is so much better.

@LATiNZkILLZ Ай бұрын

does this work when they are laying down only or does it work when the offset is sitting up

@Yahs-our-El Жыл бұрын

Hey bro okay Imagine 2 , 3/4 conduit pipes coming off a tranpeez pipe rack in the air and going to offset down and run along a 🧱 wall one stops and the other goes in these pipes are for disconnect s how would i make them parrael

@TheArtOfConduitBending Жыл бұрын

I wish I could imagine it but I can't. You would have to send me a video. Best way is either Snapchat or Instagram. Sorry I wish I could answer that for you.

@joshuamccool69 Жыл бұрын

Thank you sir

@TheArtOfConduitBending Жыл бұрын

Ty for watching

@kinghussien163 3 жыл бұрын

Wish all this was around when I was going through apprenticeship

@ryanb1874 3 жыл бұрын

Ugly book on conduit is pretty good. And even just the conduit section in the regular manual

@Tito-nw6te 4 жыл бұрын

FIRE.

@leonidasmoran2419 3 жыл бұрын

Nice Thank You For. Take Time. To Teach Us

@trentsetter2148 2 жыл бұрын

You’re badass being do this 14 never seen the tricks u use an I know em

@TheArtOfConduitBending 2 жыл бұрын

🙏🙏🙏 Please follow me on: Facebook/holmzlaw Instagram/holmzlaw TikTok/holmzlaw Reddit/holmzlaw LinkedIn/melvinrubio Snapchat/holmzlaw Tradehounds/holmzlaw Discord- discord.gg/cKgE88wW Communities: Reddit/r/conduitology Facebook/artofconduitbending LinkedIn/artofconduitbending

@ProfessionalKazak 3 жыл бұрын

Thanks bro

@cuate0882 3 жыл бұрын

Thanks 👍

@ProfessionalKazak 3 жыл бұрын

Can you make a video doing a 90° bend and with (2) 3 point saddle bends and how the shrinkage works? Making 3 bends Using one pipe?

@TheArtOfConduitBending 3 жыл бұрын

I can do a video showing you all that and how shrinkage works. But i don't know if i can fit ( 2) 3 point saddle and a 90 in one pipe. Ill get back to you. But either way i know what you want and i can show you.

@ProfessionalKazak 3 жыл бұрын

@@TheArtOfConduitBending thank you so much

@haideral-shahee2656 2 жыл бұрын

Hello buddy Holmz Law! I LOVE your all videos!! I have learned a lots from your videos! My question to you is HOW to be a confident to bend Conduit without having help from my boss or Journeyman? What I need is to be responsible to bend Conduits without making too much scrap/wrong bent conduits? Honestly, I LIKE to be just like yours to know how to bend Conduit and want to be a Professional conduits bender!

@TheArtOfConduitBending 2 жыл бұрын

My answer to you is. The best way to be a confident conduit bender is to practice and memorize the formulas. After that practice bending as much as possible. Learn from all of your mistakes and remember them. Learning how to bend is not hard the hardest part is knowing the correct formulas. Also knowing when to use a specific bend for the right situation.

@haideral-shahee2656 2 жыл бұрын

@@TheArtOfConduitBending THANK YOU for the wise answer!! I will follow your idea! ☺️👍❤️🌷

@bobbywood2146 2 жыл бұрын

Hello… I was curious if this formula applies to half inch EMT? I just watched your vid (amazing btw) and you said the formula works from 3/4 to 4” I will be doing a conduit bending test soon using 1/2” and I have to bend parallel offsets and 90’s. So my understanding is it would be .268 times spacing of center to center?! I’ll be going into a j box so according to the formula you gave my 1st mark on 2nd conduit would adjust by .335” is this correct? Hope to hear back soon and thanks

@TheArtOfConduitBending 2 жыл бұрын

I apologize. It will work for any size conduit. I just don't usually work with ½" so I forget to mention it. yes the formula depends on the degree of offset your bending all of your offsets. So if all of your parallel offsets are 30° then it would be ¼" x spacing from center to center. If you were bending 45° then it would be ⅜" x spacing from center to center. Where you threw me off is when you refer to a j box. I'm in not sure what your situation is but parallel offsets are used just to have equal spacing through out all of your bends. Like you see in the picture of my KZfaq video.

@bobbywood2146 2 жыл бұрын

@@TheArtOfConduitBending thanks for getting back to me promptly brother. Yeah for the last 8 months I was working with 3/4” EMT at the hospital but a couple weeks ago we started a project at the college using 1/2”. My test coming up I have to bend parallel offsets going from one 4” square down to another then come out the other side and run parallel 90’s to another j box then come out of that and do a 3bend saddle over an existing pipe. I’m good on others but need help on the offsets. Thank you for the help and advice brother. I’m a 1st year apprentice and have to pass the test to move on to 2nd year. I will practice your formula for sure

@TheArtOfConduitBending 2 жыл бұрын

@@bobbywood2146 just remember that the parallel adjustment for each degrees. Is the same thing as the shrink constant for offsets. It's off by such a miniscule number that it won't effect the way it looks at all. So remember shrink constant is the same as parallel adjustment. Example 30° offset parallel adjust is = 1/4" 30° offset shrink constant is = 1/4" Hope that helps. Follow me on LinkedIn if you have an account and endorse me under the skills section for any of the skills you feel I may have. I would really appreciate it. www.linkedin.com/in/melvin-rubio Follow me on: TikTok/holmzlaw Facebook/holmzlaw Instagram/holmzlaw Reddit/holmzlaw Reddit/r/conduitology Reddit/holmzlaw Tradeshound/holmzlaw Twitter/holmzlaw Quora/artofconduitbending Quora/holmzlaw

@myboysanji 2 жыл бұрын

might be a dumb question but will this method work for 3 and 4 point parallel saddles? or there is no such thing as parallel saddles only parallel offsets or 90 degree bends? thanks in advance

@TheArtOfConduitBending 2 жыл бұрын

you can use this for a 4 point saddle parallel because it's basically just 2 offsets. And yes there is such a thing as parallel 3 point saddles just rare that anyone ever has to use it. But you won't be able to use this method for it. You need to use what I call an advanced method you can find it on my advanced conduit bending playlist.

@myboysanji 2 жыл бұрын

@@TheArtOfConduitBending thanks already subbed to all you social media btw. You're the best person to learn from.

@elbato713 3 жыл бұрын

Im in industrial and use hydraulic bender. It worked when i used the formula on the same size conduit but when i used different sizes, it was off. All the math was right. And i did it multiple times. I noticed the center on the bend is different.

@TheArtOfConduitBending 3 жыл бұрын

Ok so when you use different sizes of conduit. You need to measure for each conduit center to center. Because like you said the c to c measurement is different. Im going to have to do a video explaining that. I thought i did explain it in the video. Im going to have to check. If i didn't ill make a video. I apologize for the confusion.

@elbato713 3 жыл бұрын

@@TheArtOfConduitBending your explanation was fine but it would be nice to see it done on conduit that is not the same size. And by the center i meant center of the bend. Like a couple inches behind your line where the bender starts bending the pipe. Ex : the 3/4 would start bending at 5 inches while the 1 inch would start bending around 6 inches. And again this in a greenlee hydraulic bender

@TheArtOfConduitBending 3 жыл бұрын

Ok im going to look into and work on another video with different size conduits.

@wardebremerman376 3 жыл бұрын

did you use the edge of the saddle as your start mark or use centers? i also use he big bender and i will find a center mark for each bend im going to make using scrap pieces of each size conduit on the rack. and how far that mark is from the end of shoe. Then you bend to center of bends and it will work out. Hope i explained it right. after that all the process is tghe same as he explained.

@anthonyellis9804 4 жыл бұрын

Different size conduit parallel offset, any calculation different?

@TheArtOfConduitBending 3 жыл бұрын

ok so for different size conduit. it's basically still the same. what you have to do is just space out the conduit with the spacing you want. then measure from center of conduit to the center of next conduit. then just use the formula i gave you. other than that its really just the same. or take half the size of one conduit half the other conduit plus add desired spacing in between and use formula. Sorry i couldn't get back sooner. follow me on: facebook@Holmzlaw instagram@Holmzlaw Tiktok@Holmzlaw

@ricardoayala7661 2 жыл бұрын

So on the inside how would you subtract? Have a vid of that??

@TheArtOfConduitBending 2 жыл бұрын

I don't have a video on that cause i believe i explain that in the video. Outside parallels you add onto the next conduit. If you are working from the inside then from your second conduit just subtract your answer and keep subtracting till your done with all your conduits. Its the same just reverse. Thats all. Don't make it complicated. Just take your time and think about it.

@MrMattyHess 7 ай бұрын

When you reference same thing for diff size conduit are we talking from center of bends you make the adjustments? I don’t believe it’s arrow or front of shoe?

@TheArtOfConduitBending 7 ай бұрын

I'm not sure what you are asking

@MrMattyHess 7 ай бұрын

Saying the arrow on a hand bender doesn’t represent the front of a shoe on a table bender when making adjustments for different size conduits.

@TheArtOfConduitBending 7 ай бұрын

@@MrMattyHess yes you would use center of bends. This is the norm when you start using electric and hydraulic aka table benders. Although for most of your standard benders you won't need to use COB you can use front of shoe. COB comes into play mostly when you need to place a kick in a desired spot on your conduit. Or 3 point saddles, concentric bends , or when you need to place your offset bends in a specific spot.

@eze615 2 жыл бұрын

You used half inch conduit is it the same for 3/4?

@TheArtOfConduitBending 2 жыл бұрын

yes it's the same no matter what size you use.

@paulramirez1774 2 ай бұрын

Just an fyi I think this changes as your pipe sizes change. I.E. Distance between pipes because of OD right? 🤔

@TheArtOfConduitBending 2 ай бұрын

no sir. you are probably confusing it with rolling parallels

@tellokbey6267 3 жыл бұрын

Thank you for sharing this, God bless you

@praveenbabugolla9758 3 жыл бұрын

Righting nice sir

@TheArtOfConduitBending 3 жыл бұрын

Thank you for watching. Hope this helped. Follow me on Facebook@holmzlaw Instagram@Holmzlaw Tiktok@Holmzlaw Post work here #conduitology #conduitologist #conduitologism #holmzlaw #artofconduitbending

@anthonytovar4729 Ай бұрын

I could really use some advice on keeping conduits parallel with different rises

@sadlylow2412 5 ай бұрын

what do you do with adjustment values

@TheArtOfConduitBending 2 ай бұрын

you'll add them in most cases to your offset layout on the second conduit , 3rd, 4th and so on.

@tucanblanco5393 Жыл бұрын

Just wanted to let you know that I am doing a lot of research on Bending Emt. Today I been more than 9 hours

@andrebadel8257 3 жыл бұрын

Can you make a video on sweeping a 90° bend

@TheArtOfConduitBending 3 жыл бұрын

check this video out. Not sure if this is what you mean. But i have a video doing segment 90s already. kzfaq.info/get/bejne/fMuKpJhkqq24iKM.html

@luisarreola466 2 жыл бұрын

Excelente

@TheArtOfConduitBending 2 жыл бұрын

gracias por ver mi video y comentar. Hago todo lo posible para poner subtítulos en español en todos mis videos lo antes posible. Si tiene alguna idea de video que le gustaría que haga un video, hágamelo saber. Estoy en todas las redes sociales como Holmz Law. Gracias y por favor comparta mi canal con sus amigos y compañeros de trabajo. Please follow me on: Facebook/holmzlaw Instagram/holmzlaw TikTok/holmzlaw Reddit/holmzlaw LinkedIn/melvinrubio Snapchat/holmzlaw Tradehounds/holmzlaw Discord- discord.gg/cKgE88wW Communities: Reddit/r/conduitology Facebook/artofconduitbending LinkedIn/artofconduitbending

@biz504 3 жыл бұрын

🔥🔥🔥🔥🔥🔥

@IVAN2233 6 ай бұрын

How do you use this for parallel kicks?

@TheArtOfConduitBending 6 ай бұрын

I have lots of videos on kicks these are just a couple of them. Search parallel kicks by holmzlaw. I'm posting a couple videos below. Hope this helps you. kzfaq.info/get/bejne/obh1bMWcqbjMhWw.htmlsi=j4rDvyAhG95LQ5Ha kzfaq.info/get/bejne/hdyVq7CFy9ioeHk.htmlsi=mcgIeehltDzNgxBS

@TheArtOfConduitBending 6 ай бұрын

kzfaq.info/get/bejne/obh1bMWcqbjMhWw.htmlsi=j4rDvyAhG95LQ5Ha

@josepina4622 3 жыл бұрын

I really liked the video .... I would just like to confirm if I understood correctly. When doing offset obvious the first one is done as we normally do it, right? So if I had to make another one on the outside at 30 ° Should I add the result of the formula in the first bend?

@TheArtOfConduitBending 3 жыл бұрын

So you start adding to the second, third, fourth, etc. I apologize if I wasn't clear on that. I'll try to look over the video and update it ASAP.

@anthonytovar4729 Ай бұрын

What happens if the rise changes ????

@TheRealKingish 6 ай бұрын

What if you are using segment bends?

@TheArtOfConduitBending 6 ай бұрын

Totally different calculation. You still have to use this calc. But in top of this calc you'll have to combine the segment bend calc too

@kendalbeck9032 4 жыл бұрын

I wish you could be the instructor at our Local.

@TheArtOfConduitBending 3 жыл бұрын

wow thanks dude. Well you got me on the tube my dude. Any questions i'm here and you can also follow me on facebook@Holmzlaw instagram@Holmzlaw Tiktok@Holmzlaw

@danielllanos653 2 жыл бұрын

I feel like he lopses his train of thought for trying to give us so many reminders

@TheArtOfConduitBending 2 жыл бұрын

You're probably right

@andrewjrbritt8547 2 жыл бұрын

WORD UP....!!!!

@TheArtOfConduitBending 2 жыл бұрын

Thanks for watching and thanks for the comment

@therookieca Жыл бұрын

If you bend 30 degree on the floor it's easier cause you just bend until the handle is perpendicular to the floor. For me I find it easier.

@TheArtOfConduitBending Жыл бұрын

Yes but some benders the handle straight is a 45.

@joestevens1673 4 жыл бұрын

Dog!! I cant belive nobody has taught me this

@TheArtOfConduitBending 3 жыл бұрын

Glad i can help. follow me on facebook@Holmzlaw instagram@Holmzlaw Tiktok@Holmzlaw

@isiah6189 8 күн бұрын

I know a Puerto Rican from the Bronx when i hear em

@GM2181 2 жыл бұрын

👍

@TheArtOfConduitBending 2 жыл бұрын

Please follow me on: Facebook/holmzlaw Instagram/holmzlaw TikTok/holmzlaw Reddit/holmzlaw LinkedIn/melvinrubio Snapchat/holmzlaw Tradehounds/holmzlaw Discord- discord.gg/cKgE88wW Communities: Reddit/r/conduitology Facebook/artofconduitbending LinkedIn/artofconduitbending

@Penguin545 Ай бұрын

So long story short multiply the shrinkage for whatever angle you’re bending your offset on times however many inches for the conduit spacing you were running. Example three-quarter inch with 2 inch spacing you would advance your marks a half inch per pipe to keep all the parallel bends in line with each other.

@tucanblanco5393 Жыл бұрын

If i find made in Germany tools i prefer to those then others

@Pila95112 2 жыл бұрын

You made a mistake minutes 22:22 you said 15 degrees =1/8 of an inch times center to center between conduits than you star using 30 degrees constan times center to center

@TheArtOfConduitBending 2 жыл бұрын

Thanks for the comment. I'm sorry I don't see it. I watched your time stamp and I think your mistaken. I also watched your time stamp about a couple minutes forward and back didn't see what you mentioned.

@rayburnncolas 11 ай бұрын

Half of the tangent of 30 degrees would be 1/8 correct? Using the formula it should be 1/8 times the spacing not 1/4

@rayburnncolas 11 ай бұрын

21:28

@johnnyem-grafix4024 2 жыл бұрын

Five bouroughs kid

@xxdre86xx 7 ай бұрын

Good video with great information but this could've been a 15 min video. Too much repeating.

@TheArtOfConduitBending 7 ай бұрын

I'll take that into consideration in the next one

@hardworker8048 3 жыл бұрын

To Bad I hope u do not ruined the floor when you bend it.

@TheArtOfConduitBending 3 жыл бұрын

The floor turned out just fine. Thanks for watching. Really appreciate it.

@rufushughes5602 4 ай бұрын

Please please get to the point.

@TheArtOfConduitBending 4 ай бұрын

I really apologize. It's a bad habit. I'm working on it

@sidmarterior8101 3 жыл бұрын

Too mu h explaination about ur video boy

@TheArtOfConduitBending 3 жыл бұрын

Some people need that. I apologize if it's not your style.

@jester6909 2 жыл бұрын

Good stuff

@TheArtOfConduitBending 2 жыл бұрын

Thanks for watching. Glad you like it.

@jester6909 2 жыл бұрын

@@TheArtOfConduitBending keep them coming!

@TheArtOfConduitBending 2 жыл бұрын

@@jester6909 you like the videos? How long have you been an electrician?

@jester6909 2 жыл бұрын

@@TheArtOfConduitBending 4 years brother!

@TheArtOfConduitBending 2 жыл бұрын

@@jester6909 well I'm glad you watch my videos.