I have looked at many container cranes but this is the best by far. The spreader is absolutely incredible. I wish this could be bought in a kit. I would like to think that if one of the many companies that produce models made this into a kit they would sell out fast.
@cledersontp2 жыл бұрын
Thank you! I buid a crane with 3D printing. I used your solutions for spreader opening and stabilization!
@munsterrail2 жыл бұрын
incredible work - very well done!
@johanvandenbrom33905 жыл бұрын
Prachtig dit, leuk om te zien
@pascualcontiniello28814 жыл бұрын
My buen video . Saludos.
@pascualcontiniello28814 жыл бұрын
Very Good
@ingokonen5755 Жыл бұрын
I Love this crane ... I whis ibhave this one ... Is it possible to get a construction Instruction ?!?
@lboekhoven2613 Жыл бұрын
Hello. After many years of trying is this the result. now I am busy with other things. (see "de kraan op de oude haven") don't give up trying.
@TRAIN_MAN23 Жыл бұрын
Wow how You made it move, would you like to do the same and where did you get such a crane or did it yourself
@osmanpasha_diy2 жыл бұрын
Incredible! Can you make a video about how it works? How does the whole crane move, is the motor inside the crane or under the table? How big are the motors, did you gear them down? What model of the motor is this?
@lboekhoven26132 жыл бұрын
Hi! Only the motor for moving the Crane is under table. It is a motor from an old VHS recorder. The others are: moving, lifting grabbing, and lifting the beam. These are micro DC motors with gear. From China.
@osmanpasha_diy2 жыл бұрын
@@lboekhoven2613 thank you for the response! And did you gear the motors down? How did you make such tiny gears?
@lboekhoven26132 жыл бұрын
@@osmanpasha_diy Find the N10 motors with planetair gearbox. There are lot of choises.
@osmanpasha_diy2 жыл бұрын
@@lboekhoven2613 thank you! I'll definitely try something like this in future
@jeromedonofrio84346 жыл бұрын
hello, what the brand of your container crane ? it's very interesting. i like it.
@lboekhoven26136 жыл бұрын
jerome D'ONOFRIO the original model was Roco 1805. I Think it is not on the market anymore. I changed it in a ship to shore.
@Night-zn4ew3 жыл бұрын
How is this motorised, does it use PCBs and if so where can I get them? How much did this cost in total
@lboekhoven26133 жыл бұрын
Hi Jammy, just small micromotors, no PCBs. The ROCO1805 is not on the market anymore. But my next model will be 3d printed and mayby designed for production.
@Night-zn4ew3 жыл бұрын
@@lboekhoven2613 How is it controlled without a circuit board? Also, you can get them on eBay.
@randysrockandrollrailroad82075 жыл бұрын
Cool
@Night-zn4ew3 жыл бұрын
How did you make it move without PCBs, surely you need them to control the micromotors.
@lboekhoven26133 жыл бұрын
What do you mean PCBs? I use 3 speedcontroles, that is all!
@Night-zn4ew3 жыл бұрын
@@lboekhoven2613 PCB Printed Circuit Board. Basically a computer. But I understand, it all links back to that tangle of cables in the crane jib.
@lboekhoven26133 жыл бұрын
@@Night-zn4ew Yep!
@Night-zn4ew3 жыл бұрын
@@lboekhoven2613 I will be using DCC to make mine move as that allows for accessories like lights and most importantly, the electromagnet to grab the containers.
@lboekhoven26133 жыл бұрын
@@Night-zn4ew Grabbing containers with elektromagnets is not easy. I grab the container with a force on the front and rear side of the container. I like the idea that the grabber is telescopic and it is as long as the container you will grab.
@Vinserietje19887 жыл бұрын
Wat een prachtige containerterminal. Is dit zelfbouw of zo gekocht?
@lboekhoven26137 жыл бұрын
Vincent S In deel 1 heb ik een reactie geschreven. het origineel is een bouwpakket van Roco, nr 1805. dit is nog maar zelden te koop op beurzen. ik heb het bouwpakket flink verandert. de spreader, de grijper voor containers is 100% eigenbouw, mbv 3d printer. De originele kraan kan je zien in de filmpjes van andolik op KZfaq.
@JamesBondsSkyline7 жыл бұрын
I am motorising a Kibri container crane at the moment, I'm currently designing a new spreader for it, what would be best for the motor to grab the container? I'm not sure what would be best? Congratulations on your design of spreader, it has given me confidence on a future design
@lboekhoven26137 жыл бұрын
I used a micromotor with planetaire gear for adjusting the spreader, and grabbing the container. One motor for two functions makes it easyer to build.
@JamesBondsSkyline7 жыл бұрын
Thank you for your reply. I was not sure about using a micro motor as I did not think it would hold the container. I will have a go at my design and see how it goes. I will certainly plan to produce and build a spreader like yours, once I have learnt 3D design
@JamesBondsSkyline5 жыл бұрын
Out of curiosity, where did you buy the gears from?
@lboekhoven26135 жыл бұрын
Find them on this chinese website. look for geared micromotor, or planetair gear micromotor
@karmashift2485 жыл бұрын
👍👍👍👍👍👍👍👍👍👍👍👍
@simon_xf48033 жыл бұрын
Hallo Ik ben zeer onder de indruk van de werking van de spreader ben al langere tijd op zoek naar een werkende H0 spreader . Zijn er mogelijkheden om er 1 bij u te kopen ? groeten Arjan
@lboekhoven26133 жыл бұрын
Nee, het spijt me, maar ik kan geen productie opzetten, en kwaliteit, en garantie leveren zoals dat zou moeten.
@peterrobson14812 жыл бұрын
Aode eu compro um produto dese equanto custa
@lboekhoven26132 жыл бұрын
Sorry, I don't understand!
@JamesBondsSkyline6 жыл бұрын
Where would a good source be to find out size and dimension of the spreader? I have made a first draft of a spreader on the 3D printer but I’m not sure it is correct size. I have googled for images and I think I found dimensions in metres? Kind regards Iain
@lboekhoven26136 жыл бұрын
Start with the dimensions of the containers: If you want to pick up 20ft containers, and 40 ft containers, the spreader "lenght"should be about 6 cm, the telescope length is about 3 cm on each side.
@lboekhoven26136 жыл бұрын
In scale HO of course!
@JamesBondsSkyline6 жыл бұрын
Excellent, thank you for your help.👍🏻
@eisenschweinchen53544 жыл бұрын
Great! Selfmade?
@lboekhoven26134 жыл бұрын
scratch building from ROCO 1805. Motorised with micromotors. Spreader designed, engineered, and 3d printed by myself.
@eisenschweinchen53544 жыл бұрын
Congratulations!
@JAALMARZA6 жыл бұрын
Nice job!👍👍👍
@jhonny13927 жыл бұрын
Thank you so much for sharing. This new Spreader is simple FANTASTIC ! ! !. Your project is a great inspiration for me. I hope in the near future can do something similar; the only problem for me is mine has to be in N scale ! and this is gonna be a HUGE CHALLENGE !, but I'll do my best or at least, I´ll try . . . Congrats, and cheers from Chile, South America, John.
@darrinto6 жыл бұрын
I love the way you have made this and I would like your input on how one can be made for O Scale containers .
@lboekhoven26136 жыл бұрын
Hi, I 'm not used to this scale, but I think the system will work, also in this scale, if the containers are not to heavy.
@darrinto6 жыл бұрын
Thank you for your reply where can I find the same set up at my email is darrintorrence@gmail.com
@captainugros4 жыл бұрын
what brand is the crane?
@lboekhoven26134 жыл бұрын
Roco 1805. But it is not on the market anymore. I changed this crane to a ship to shore.
@christtking8945 жыл бұрын
Nice! Who is the manufacturer?
@lboekhoven26135 жыл бұрын
Roco 1805 is the original Crane. But I rebuild, and motorized it.
@teadyconnolly95907 жыл бұрын
Hi I Boekhoven I am trying to get HO Container Gantry Crane Fully Functional for over 4 years I want to know would you be interested in selling this model or would you be able to make the same crane for me please i am very impressed with this project beautifully designed I am praying hard that you will please contact me with good news I am living in Ireland I have 4 static HO Cranes and 1 Fully Functional 0 scale Lionel MI-Jack which is Fully Functional but there is no Jib / Grab and I can send this model to you have another project to get going I will be able to show you the Container Terminal I have only 125 well cars all going coming and going from the switching and the rest you can see very soon hopefully thanks again for excellent videos on your Container Gantry Crane I have to very well done on this model I am just hoping you get this Gmail
@teadyconnolly95907 жыл бұрын
Hi I Boekhoven I am just after getting my Skype going just wondering would you be able to get in contact with me please about this Container Gantry Crane please just to have a good chat and see how soon you can build HO Fully Functional Container Gantry Crane with all the specials Teady Freight Yard
@lboekhoven26135 жыл бұрын
I am sorry, this is not working. You need to search for the settings, and change the drawings to make it slide perfectly. The geared motor is not powerfull. So please try to draw it yourself.
@renekromhout91533 жыл бұрын
Zin
@renekromhout91533 жыл бұрын
Maak jij deze spreaders ook voor anderen ik ben zeer geintreseerd om er 2 te kopen bij je groetjes r kromhout
@lboekhoven26133 жыл бұрын
@@renekromhout9153 Hallo, René Kan ik contact met je opnemen?